Showing results: 136 - 150 of 351 items found.
-
Instron
Instron offers a wide range of Durability Testing Products such as Controller and Software modules, Hydropuls actuators (linear & rotary), Servo valves, Sensors, Power Packs & Accessories and Test frames & fixtures.
-
RF-200 -
Neulog
The RF Communication module allows remote operation of asingle sensor or a chain of sensors. The remote single sensoror chain is connected to an RF Communication module and to aBattery Module which powers them all.
-
KD-5100 -
Kaman Fuzing & Precision Products
* Two precisely matched sensors per channel give resolution to a nanometer.* Superior thermal and long-term stability of 5x10-6 inches/month or better.* Small package size: 2 x 2.12 x 0.75 inches thick.* Cryogenic sensors available.* High sensitivity: up to 10 V/mil (394 mV/mm).* Low power consumption: less than 2W @ ±15 Vdc typical.
-
90229 -
HITEC Sensor Solutions Inc.
SDI’s 90229 is designed for calibrating tools used to apply torque including electric and pneumatic power tools, torque sensors, hand and click wrenches. The strain gage based reaction torque sensors in the bench-mount housing remain stationary while torque is applied. The housing dis-assembles by removing two snap pins, allowing the user to easily change socket sizes and capacities.
-
TCM-1A -
Macintyre Electronic Design Associa
The TCM-1 is a three-channel portable signal conditioner specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from either its internal batteries or the power line. It incorporates two sets of power line rejection filters, switch selectable for 50 or 60 Hz and the corresponding first four harmonics.
-
WIKA Alexander Wiegand SE & Co. KG
For on-site display of pressure values, pressure sensors can be combined with attachable indicators, for the central pressure indication there are digital indicators for panel mounting available. Our electrical accessories also include power supply and control units, intrinsically safe repeater power supplies and also pre-assembled connectors with cables.
-
40-292-012 -
Pickering Interfaces Ltd.
A simple solution for applications requiring a programmable load resistor with up to 15W power handling. It is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors.
-
MCx1101 Family -
ACEINNA Inc
Power architects are continually asked to push the boundaries for system efficiency, response time, small size, and low cost in new power system designs. Most modern designs require current sensors to help implement the complicated control, telemetry, and protection circuitry essential in meeting these difficult design goals.
-
mks Ophir
Photodiode sensors have a high degree of linearity over a large range of light power levels: from fractions of a nanowatt to about 2 mW. Above that light level, corresponding to a current of about 1 mA, the sensor saturates and reads erroneously low. Therefore, most Ophir PD sensors have a built-in and removable attenuator allows measurement of up to 3 W without saturation.
-
SAM-3 -
Macintyre Electronic Design Associa
The SAM-3 is a portable single channel signal conditioneer specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from eitherits internal batteries or the power line. It incorporates two sets of power line rejection fileters, switch selectable fro 50 to 60 Hz and the corresponding first four harmonics.
-
Columbia Research Laboratories
Columbia Research Labs line of Force Balance Linear Accelerometers offers low cost, high performance, general purpose single axis accelerometers that are ideal for DC and low frequency measurements, with both voltage and current signal outputs available. Also offered are Columbia's Solid State Sensors and our specialized Airborne Sensors that generate outputs specifically designed to operate from +24 to +32VDC aircraft power, that is excellent for airborne telemetry applications. And our Low Noise Sensors are designed for use in seismic, low level, low frequency motion studies.
-
Iris Power LP
Iris Power provides partial discharge sensors, instruments, diagnostic software needed to understand the condition of your isolated phase bus in order to identify issues, localize the problem and prioritize corrective measures prior to failures.
-
BAT-200 -
Neulog
The Battery module supplies power to a sensor, or chain ofsensors, operating in the Off-Line mode, and to sensors connectedto an RF communication module.The Battery module can be recharged by connecting it to the PC'sUSB socket via the USB module's USB cable.
-
Keysight Technologies
The EPM and EPM-P Series provides high-performance, programmable power meters for CW, average and peak power measurements. EPM Series: measure average power over a range -70 dBm to +44 dBm, and over frequency range 9 kHz to 110 GHzEPM-P Series: measure peak, average and time-gated power over -65 dBm to +20 dBm, to 18 GHz using E932XA power sensors. It provides complete pulse and statistical analysis with PC software via the GPIB or RS232
-
HyperOCR -
Sea-Bird Scientific
Hyperspectral ocean color radiometer (HOCR) sensors are designed for applications where performance, size and power are key constraints. HOCRs can be mounted on real-time profilers, moored on autonomous deepwater buoys, installed in autonomous underwater vehicles, as well as on ships and airplanes for above-water optic applications. HyperOCR sensors are fully digital optical packages, providing 136 channels of calibrated optical data from 350–800 nm.