Filter Results By:

Products

Applications

Manufacturers

PC

Checking personal computers and using a pc as host to perform test.


Showing results: 706 - 720 of 1672 items found.

  • Model Vector Network Analyzer

    DZV-1 - Digital Signal Technology, Inc.

    DZV-1 is the vector network analyzer which can be measured the impedance and VSWR of the antenna, S Parameter of RF component and devices. It is small and low-priced. So, it is suitable for the production line, laboratory use, various testing applications, and the educational use. The communication between the DZV-1 unit and PC is done via USB, which is also used for power supply. The LOG-MAG characteristic, the phase-characteristic, the group delay frequency characteristics, the Smith chart, the polar coordinates, the SWR characteristic can be displayed on PC.

  • Heavy Duty Dissolved Oxygen Meter

    Extech 407510 - Extech Instruments Corporation

    407510 is a Heavy Duty Dissolved Oxygen Meter with PC interface. Recall Min, Max and Average readings. Featuring Data Hold and a Built-in RS-232 PC serial interface with optional data acquisition software and data logger. Auto power off saves battery life. DO measurements from 0 to 20.0 mg/L. Complete with 0.8" (20mm) diameter probe on 13ft (4m) cable, 5 membranes, rubber holster, 9V battery and hard case.

  • UV Penetration & Protection Test System

    TF131 - TESTEX Testing Equipment Systems Ltd.

    UV Penetration & Protection Test System. Fabric Samples are measured in a double beam spectrophotometer with an integrated sphere. The sample is scanned over the UVA and UVB regions of the spectrum and transmitted radiation is efficiently collected by the detector within the integrating sphere. The software calculates UV penetration factors and sun protection factors from the scan data. It runs on a PC under Microsoft Windows and controls the spectrophotometer, automates the measurement process and generates a printed report. PC and printer are not included.

  • Intelligent Interface Card

    IIB-1553-ISA - Western Avionics Ltd.

    The IIB-1553-ISA is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for PC compatible computers, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-ISA supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multilevel triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. PC memory space utilised by the board is selectable.The board is supplied with C drivers in source code and Windows menu driven software as standard.

  • Intelligent Interface Card

    IIB-1553-PC104 - Western Avionics Ltd.

    The IIB-1553-PC104 is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for PC compatible computers, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-PC104 supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a single, dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. PC memory space utilised by the board is selectable. The board is supplied with C drivers in source code and Windows menu driven software as standard

  • 3CH Gas Mixer

    G-MIX 3CH - BioAge s.r.l.

    G-MIX is a versatile integrated system that can be easily used to create innumerable gas mixtures, the gas flows are accurately controlled by three MFCs (Mass Flow Controllers), each MFC has stored within its memory the calibrate tables for 10 gases different. The entire hydraulic system was created using AISI316 stainless steel pipes, fittings and valves, using the best solution available for this type of application. The stoichiometric composition of the gaseous mixture can be easily controlled via a software developed by Bioage, with an intuitive and friendly interface that can be easily installed on a common PC and communication with G-MIX is possible by means of a USB port. The System Can be used in Stand-Alone mode, without any connection to the PC thanks to the easy and intuitive LCD display with which each MFC is equipped, setting the gas parameters using an intuitive keyboard with which the MFC is equipped.

  • Data View Current & Voltage Logger

    DVCV - Supco

    INSTANTLY record and view critical performance parameters with the Dataview Series DVCV for Current, Voltage and Watts. Monitor real time measurements, and download to your PC for further analysis.

  • CardBus Card Interface Board

    PCCextend 125CIB - Sycard Technology

    For those applications that require access to the CardBus PC Card that can't use a standard extender card, Sycard provides the PCCextend 125CIB (Card Interface Board) which allows full access to all 68-signal and power pins on the CardBus peripheral. Standard 0.1" headers allow the user to connect standard 34-pin ribbon cable to test or prototype hardware.

  • CZT Gamma-Ray Detector Spectrometer

    GR Family - Kromek Group plc

    The Kromek GR family is a range of CZT-based high-performance gamma-ray spectrometers. They are completely self-contained, with built-in preamplifier, shaping amplifier, baseline restorer, pulse height digitizer, and HV supply. The digitized pulse heights of detected gamma-ray signals are sent to a PC via the USB. The unit is powered entirely from the USB bus, so no external power supply is needed.

  • ETX

    Axiomtek Co., Ltd.

    The ETX modules (114 x 95 mm) are very compact and highly integrated SBCs that integrate core CPU and memory functionality, standard personal computer (PC) peripheral function such as graphics, USB, serial and parallel ports, keyboard/mouse, Ethernet, IDE, PCI, and ISA buses. All ETX modules have a standardized form factor and a standardized connector layout.

  • Fifo Serial Analyzer 2 TO 1 Breakout Boxes

    FLL221/FLL221S - Fifo Electronics

    The FLL221 BreakOut Box is designed to be used with the FLL and FSA serial analyzers when they run on PC's with only one ComPort. The serial line passes through FLL221 using the 9-pin connectors. Data from both pin 2 and 3 of the serial line is available on the FLL221 output. The output cable from FLL221 is connected to the ComPort of the PC running the analyzer.

  • J2534 PassThru

    MaxiFlash Elite - Autel

    As a multi-protocol Pass-Thru vehicle interface, MaxiFlash Elite is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device. Specially designed to provide users with convenient PC communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, MaxiFlash Elite offers the most significant features desired by OEM customers: reliability, fast performance and flexibility.

  • miniPCI POST Code Display

    post5a - PC Engines Gmbh

    miniPCI format to fit WRAP boards and most modern notebook PCs. During power on self-test (POST), most PC BIOSes will write diagnostic codes to port 80h or port 84h (auto select, whichever is written first). Use post5a to display these codes on a dual digit LED display. Additional LEDs indicate the status of the power supply rails.

  • miniPCI POST Code Display

    post5a1 - PC Engines Gmbh

    MiniPCI format to fit WRAP boards and most modern notebook PCs. During power on self-test (POST), most PC BIOSes will write diagnostic codes to port 80h or port 84h (auto select, whichever is written first). Use post5a1 to display these codes on a dual digit LED display. Additional LEDs indicate the status of the power supply rails.

  • Optical Sensors

    Hamamatsu Photonics K.K.

    module is basically comprised of a photomultiplier tube to convert light into electrical signals, a high-voltage power supply circuit, and a voltage divider circuit to distribute the optimum voltage to each dynode, all assembled into a single compact case. In addition to these basic PMT modules, Hamamatsu also provides modules having various additional functions such as signal processing, cooling and interface to PC.

Get Help