-
product
Squid PCI Express Carrier Boards for M.2 SSD Modules
SKU-064-2X
Flexible x1 PCI Express to 3 MiniPCI Express Splitter (Splitter) was designed to expand modern motherboard (ATX, mini ATX etc.) that have PCI Express interface. It allows you to connect up to three MiniPCI Express add-in boards to the standard motherboard PCI Express connector.Splitter includes 3 MiniPCI Express adapter boards, x1 PCI Express host board and 3 flat PCI Express Cables.
-
product
PMC-XM
The PMC-XM is intended for use in situations where the user wants to control the design. PMC-XM has two FPGA devices built in. The first device takes care of the PCI interface, DMA etc. The second device [Virtex XC4VSX35-10] is for the user application. The Transition Module [XM] is attached to the Virtex device.
-
product
8 Channel A/D & D/A Zynq UltraScale+ RFSoC Processor - SOSA Aligned 3U VPX
Model 5550
- Now available in RFSoC Gen 3 with the Model 5553- Supports Xilinx® Zynq® UltraScale+™ RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- 10 GigE Interface- 40 GigE Interface- Optional VITA 67.3C optical interface for backplane gigabit serial communication- Dual 100 GigE UDP interface- Compatible with several VITA standards including: VITA 49, VITA 46, VITA 48, VITA 67.3C and VITA 65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Model 8256 3U VPX SO...show more -
product
Powered NIM Crate
NIM Compact 150W
The WIENER NIM compact series is the low-cost entry into the NIM world. This is achieved by combining the economic steel-aluminum UEN 04 bin with a very compact 150W slot power supply. The result is a lightweight NIM crate with reduced depth. To be compatible to all NIM modules the UEP15 provides all standard (6) DC voltages as well as 115V AC.
-
product
PXI 2A Multiplexer, 8-Bank, 4-Channel 4-Pole
40-614-005
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
Data Acquisition DSP Based 16 Channel
CPCI-AD8-opt8
The CPCI-AD8/16 module provides a 3U high performance data acquisition subsystem. There are (8) eight or (16) sixteen 100/200 KSPS ADC’s for maximum performance. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface.
-
product
Embedded MXM GPU Module With NVIDIA RTX™ ADA 3500
EGX-MXM-AD3500
- NVIDIA Ada Lovelace Architecture- Standard MXM 3.1 Type B (82x105 mm)- PCIe Gen 4 x16 Interface- 5120 CUDA® Cores, 40 RT Cores, and 160 Tensor Cores- 23 TFLOPS peak FP32 performance
-
product
PXI/PXIe High Density Electro-mechanical Relay Module, 50xSPST, Normally Open
42-145A-001
The 40-145A-001 (PXI) and 42-145A-001 (PXIe) 50xSPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
product
PXI 2 Amp Multiplexer, Single 4-Channel, 8-Pole
40-635A-104
The 40-635A-104 is a single 4-channel, 8-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
SMARC Short Size Module with NXP i.MX 8M Plus
LEC-IMX8MP
ADLINK LEC-IMX8MP, based on the powerful NXP i.MX8M Plus (quad core Arm Cortex-A53) processor with an optional Neural Processing Unit (NPU) operating at up to 2.3 TOPS., is the first SMARC revision 2.1 compliant module focusing on machine learning and vision, advanced multimedia, and industrial IoT with high reliability. Additionally, it supports dual Image Signal Processors and two camera inputs for an effective Vision System. The LEC-IMX8MP is suited for applications such as smart home, building, city and industry 4.0.
-
product
Squid PCI Express Carrier Board™ for M.2 and NGSFF (NF1) SSD Modules
Amfeltec Squid PCI Express Carrier Board™ for M.2 and NGSFF (NF1) SSD Modules
-
product
Pneumatic Subsystem
OTP2-Modul-Nr050
With the pneumatic subsystem, a roller terminal, a maintenance unit, a main vent, a pressure reducer and 8 2/3-way vents are installed in the system. The extension of the module can create new possibilities for your test system.
-
product
PXI ARINC 608A Switch Modules
The matrix module is based on our proven BRIC format and can be specified as a 4 or 8 slot module. The module can be fitted with a combination of Resource Distributor and Bus Matrix Input daughter cards as required by the user. The maximum configuration is six Bus Matrix and two Resource Distributor cards fitted in a BRIC8 module.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber, LC Connectors
42-850A-414-M50
The 40/42-850A-414-M50 is a PXI/PXIe 4-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
Thermocouple, Module, ITA, 90 Series, 64 Position
510108124
Primary mating module 510104133. (May mate with other Receiver modules, as well.)
-
product
NIM Instrumentation
Berkeley Nucleonics Corporation
is a bin and power supply combination for plug-in modules. It can house twelve single-width modular instruments or a mixture of other sizes equivalent to twelve singles. Units that can be installed include BNC's modular digital delay generators, trigger pulse amplifiers, pulse generators, programming interfaces and the instruments of other companies that are designed to NIM standards.
-
product
WiGig RF Tester
IQgig-RF Model B
When used in conjunction with IQgig-IF, an optimized test solution for conducted testing of WiGig chipsets and baseband modules, the IQgig family products provide a total test solution for R&D characterization and high volume manufacturing.
-
product
8-Channel 200 MHz A/D with DDC, VITA 49.0, Virtex-6 FPGA - 6U VPX
Model 58664
- Supports Xilinx Virtex-6 LXT and SXT FPGAs- PCIe output supports VITA 49.0 VITA Radio Transport (VRT) Standard- Eight 200 MHz 16-bit A/Ds- Eight multiband DDCs (digital downconverters)- Two multiboard programmable beamformers- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 239Ω
40-251-013
The 40-251-013 is a programmable resistor module with 8 channels which can be set between 1Ω and 239Ω with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXIe Vector Network Analyzer, 300 kHz to 6.5 GHz
M9371A
Pay for only the frequency range you need with a choice of six frequency ranges up to 26.5 GHz Improve accuracy, yield and margins with the best PXI VNA speed, dynamic range, trace noise and stability Add functionality to your test system with a full 2-port VNA that fits in a single PXI slot Address your multiport applications needs by cascading multiple models Increase throughput and lower costs by adding modules in a multi-site configuration
-
product
PXI-8517, 2-Port PXI FlexRay Interface Module
780689-02
2-Port PXI FlexRay Interface Module—The PXI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PXI‑8517 contains two fully functional FlexRay interfaces, allowing an individual ECU to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
product
Interface Module
MC
The MC mezzanine module is designed to receive external commands and issue synchronization pulses on the TTLTRG line (for VXI and other devices) and the LVDS line (for LXI devices).
-
product
Virtex-5 XMC/PMC
XMC-FPGA05D
Curtiss-Wright Defense Solutions
The XMC-FPGA05D high density I/O module controlled by a user programmable Xilinx Virtex-5 FPGA and supported by a range of front panel I/O modules including analog I/O, RS-485/422, LVDS and Camera Link.
-
product
PXI 8 Slot BRIC 138x8 1-Pole Dual Analog Bus (3 sub-cards)
40-560A-121-138X8-M
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-140
The 40-297A-140 (PXI) and the 42-297A-140 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 102 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Logic Analyzer Probe
FS2512
The FS2512 is a logic analyzer probe used to test DDR4 SO-DIMM memory. When used with the triggering and analysis capabilities of Keysight’s U4154A/B/64A logic analyzer modules, it gives the user an extremely effective tool for debugging, testing and verifying DDR4 SO-DIMMs.
-
product
COM Express Type 6
The COM Express Type 6 modules are designed with all components necessary and offer the most updated bus interfaces. The COM Express modules satisfy a wide range of vertical embedded applications with features of great computing performance and rich I/O capabilities, and reduce customers' time-to-market and ownership cost.
-
product
PXI/PXIe 15W Programmable Resistor Module
42-254-031
The 40-254-031 (PXI) and 42-254-031 (PXIe) are programmable resistor modules with 1 channel which can be set between 1Ω and 13.6Ω with 0.25Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
product
Connector, 104-Pin D-Type Male, Solder Bucket, 5A
92-960-104-M
This 104-pin male D-type connector allows users to create their own cable assemblies. Cable connection is via solder buckets - supplied without backshell. This connector is not compatible with Pickering modules that use the 104-pin D-type connector.