-
product
3-Port ROADM / TOADM
Optoplex's Reconfigurable Optical Add/Drop Multiplexer (ROADM) module, also known as Tunable Optical Add/Drop Multiplexer (TOADM), is based on a proprietary micro-optics and micro-actuator design, athermal packaging technology, and state-of-the-art thin-film coating. When receiving a stream of optical signals of a plurality of wavelengths from the Input-Port (IN), this 3-port ROADM device directs a selected channel to the Drop-Port (ADD/DROP) and the remaining channels to the Express-Port (EXP),...show more -
product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-01
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
product
PXIe Audio Analyzer
M9260A
M9260A is significantly different from the traditional general purpose PXI digitizer modules which are being used for today's audio measurement. In order to achieve fast test speed and high performance it comes with large one million sample arbitrary waveform buffer and one million sample "limitless" input buffer, as well as super-linear/low noise amplifiers and digital to analog converters. This enables M9260A's ultra-low residual distortion and high amplitude accuracy. M9260A is now an important part of Keysight Radio Test Solution, and may also be easily integrated into any audio related PXI test system with its developer-friendly drivers and commands.
-
product
PXI 4 Slot BRIC 60x16 2-Pole (4 sub-cards)
40-561A-022-60X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Wi-Fi Network Equipment Amplifiers
We offer discrete and integrated amplifier solutions for Wi-Fi network equipment. Our integrated Wi-Fi modules can include multiple power amplifiers, low noise amplifiers (LNAs), switch solutions, filters (band-edge, cellular coexistence, harmonic and out-of-band rejection), diplexers, power management and device matching.
-
product
Network Monitor & Analyzer
CommView for WiFi
CommView for WiFi is a powerful wireless network monitor and analyzer for 802.11 a/b/g/n networks. CommView for WiFi can help you view and examine packets, pinpoint network problems, perform site surveys, and troubleshoot software and hardware. Includes a VoIP module.
-
product
LXI Scalable Matrix - 2Amp 10x40 Matrix Plugin Module
65-219-201
This plug-in module is part of a scalable matrix platform designed to provide a large matrix solution with 2A current carrying capacity on all Y paths.
-
product
PXIe Semi-Dynamic Digital I/O Module, 64-Channel
42-419-001
The 40-419-001 (PXI) and 42-419-001 (PXIe) are a 64-channel digital I/O modules suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. They can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
product
NI-9421, 24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module
779136-02
24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module - The NI‑9421 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels and has an LED indicating the state of that channel. The NI‑9421 offers isolation between the input channels and earth ground.
-
product
PXI/PXIe RF Matrix, 8x4, 100 MHz, 75 Ω SMB With Loop-thru
42-729A-101-L
The 40-729A-101-L (PXI) and 42-729A-101-L (PXIe) are 8x4 75 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
product
PXI 8 Slot BRIC 120x8 1-Pole (4 sub-cards)
40-561A-121-120X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Tracker
For regions with stable weather conditions, PSE provides two outdoor bi-axial trackers, which keep test samples perpendicular to the sun. PSE trackers are designed for outdoor testing and certification of both solar thermal collectors and PV modules. With our trackers it is possible to test more than one collector at the same time. Simultaneous collector testing can allow direct comparison of different collector designs under identical conditions or increase the measurement throughput of collectors and modules. In our product line we offer the following tracking systems:
-
product
PCI Express PMC Carrier
TPCE260
The TPCE260 is a standard height PCI Express Revision 1.1 compatible module that provides one slot for a single-width PMC module used to build modular, flexible and cost effective I/O solutions for all kinds of applications like process control, medical systems, telecommunication and traffic control.
-
product
PXI/PXIe RF Matrix, 8x4, 300 MHz, 50 Ω SMB With Loop-thru
40-729A-001-L
The 40-729A-001-L (PXI) and 42-729A-001-L (PXIe) are 8x4 50 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
product
PXI Dual 12x4 Matrix, 1 Pole Switching
40-511-021
The 40-510 series of matrix modules feature a wide range of selectable switching configurations (12x4,dual 12x4,12x8 and 24x4). Typical applications include signal routing in ATE and data acquisition systems. Available reed relay formats are 1-pole, 2-pole and 1-Pole screened. The screened version is suitable for switching signals up to 50MHz. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules.
-
product
Gate Scanner
SR200`
Stanford Research Systems, Inc.
The SR200 Gate Scanner module is designed to automate waveform recovery with the SR250 and SR255 Gated Integrator modules. Waveform recovery is done by slowly scanning the gate of the integrator over the waveform of interest.
-
product
75 Ohm Mini SMB Cable Assembly
40-977-751-1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
4-Channel 200 MHz, 16-bit A/D with Virtex-7 FPGA - 6U VPX
Model 57760
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four or eight 200 MHz 16-bit A/Ds- 4 or 8 GB of DDR3 SDRAM- PCI Express (Gen. 1, 2 & 3) interface up to x8- Sample clock synchronization to an external system reference LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Voltage Meter
MDS32
M-module MDS32 is a mezzanine module designed to analyze the state of discrete sensors. М-module MDS32 is installed on the mezzanine carrier - module НМ-М and connected to it via a local information highway. Up to four m-modules of various types can be installed on the NM-M module. The NM-M module together with the m-modules installed on it forms a C-1 VXI module for 64 analyzing channels and is used to create information measuring VXI systems.
-
product
Expansion Adapter Chassis
TB3-TO-CMC-LP
The TB3-TO-CMC-LP is an expansion adapter chassis using the Intel Thunderbolt 3 interface. The adapter allows the use of a front I/O XMC or PMC card outside its normal confines of a single board computer (SBC) or PC hosted carrier card. The TB3-TO-CMC-LP enables the deployment of XMC or PMC modules in systems previously unable to host them -- laptops, small form factor PCs, and other computers lacking add-in slots.
-
product
Portable Signal Conditioning System
SCS-800
The SCS-800 is a high-performance signal conditioning system for PC-based data acquisition. An SCS-800 system consists of an AC operable chassis and up to 8 multi-channel modules.
-
product
Analog Signal Conditioning &Isolation Products
DSCIA
DSCIA module is a signal channel isolated analog input or output.
-
product
PXI-8433, 2-Port, Isolated, RS485/RS422 PXI Serial Interface Module
779744-01
2-Port, Isolated, RS485/RS422 PXI Serial Interface Module - The PXI‑8433/2 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
I-V Tracers
EKO I-V tracers (MP-160 / MP-11 / MP-180) can be used in three different Power ranges. The research type MP-160 is an all round instrument to be used with single cells and modules or multiple unitswhen connected to the multi channels selectors. The portable MP-11 with remote sensor unit can be used on site to accurately check the performance of Modules and Strings. The high end MP-180 is capable to make high precision I-V measurements of small and large size solar cells and is most suitable for Research and Development applications or production inspection purposes indoors.
-
product
Input Modules
A Range of Input Modules To Support Most ApplicationsMix and match input modules for even greater flexibility. Up to 4 modules can be installed in the Synergy portable or Qb, 8 modules in the Synergy 8 and 16 modules in the Synergy Rack system.
-
product
PXI 12-Slot BRIC Matrix, 15x32 1-Pole (3 sub-cards)
40-562B-321-15X32
The 40-562B-321-15X32 is a high density BRIC12 matrix module with a size of 15x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI 12-Slot BRIC Matrix, 110x16 1-Pole (10 sub-cards)
40-562B-321-110X16
The 40-562B-321-110X16 is a high density BRIC12 matrix module with a size of 110x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
Chassis - Control up to 16 Modules with as Many as 32 Two Pole Relays Per Module Allowing 1xN Multiplexers up to 1020x1, 2 Pole Muxes up to 512x1 or 2xN Matrix Configurations up to 256x2
JX/256-MF
These Chassis control up to 16 modules with as many as 32 two pole relays per module allowing 1xN multiplexers up to 1020x1, 2 pole muxes up to 512x1 or 2xN matrix configurations up to 256x2. Jumpering option allow the modules to be controlled as separate smaller muxes, i.e. 64 4x1 2 pole muxes, or combine specific groups to allow an almost unlimited combination of sizes. Add a Control Module and optional manual control to complete the system.
-
product
QSeven
ROM-7420
ROM-7420 Qseven Module integrates an ARM Cortex-A9 NXP i.MX6 series ultra low power SoC and I/O solution chips with Linux. NXP i.MX6 supports 2D, 3D graphicsacceleration, full HD 1080P video decoding and an HD 1080p video encoding hardware engine.
-
product
OSM R1.1 Size-L Module Based On MediaTek Genio 510 Series Processor
OSM-MTK510
The OSM-MTK510 is an OSM R1.1 Size-L module featuring the advanced MediaTek Genio 510 series processor. Equipped with a dual-core Arm Cortex-A78 and a quad-core Cortex-A55, it boasts an impressive MediaTek DLA+VPU AI engine capable of up to 3.2 TOPS, making it ideal for edge AI applications. This module excels in providing edge AI processing at ultra-low power consumption.
