Showing product results. 1966 - 1980 of 4959 products found.
-
Model KM 926 - Kusam Electrical Industries Limited
• KM 926 designed according to the IEC 651 TYPE 2 & ANSIS1.4 TYPE 2 for sound level meter.• Instantaneous sound measure function.• Measurement Range : 30 ~ 130decibel• With two equivalent weighed sound pressure levels, A & C.• Fast & Slow dynamic characteristic modes.• AC & DC signed output for frequency analyzer level recorder, FFT analyzer, graphic recorder etc.
-
Dhanbad Lab Instruments India Pvt Ltd
A torque meter is a gadget for measuring and recording torque on a turning framework, for example, a motor, crankshaft, gearbox, transmission, rotor, a bike wrench, or top torque analyzer. Static torque is moderately simple to gauge. Dynamic torque, then again, isn't anything but difficult to gauge, as estimating the effect from the pole to the static framework, for the most part, requires the exchange of some impact (electrical, water-powered or attractive).
-
KL-03(III) - Kelilong Electron Co.Ltd,
KL-03(III)Waterproof Pen-type pH Meter *Large and easy-to-read LCD*Replaceable pH electrode*Waterproof design*Data holdTechnical Specification Model KL-03(III) Measuring range 0.00~14.00PH Accuracy ±0.1PH Resolution 0.01PH Operating Temperature 0~50.C Automatic Temperature Compensation 0~50.C Power Supply 4X1.5V(AG13) Dimensions 188X35X35(mm3)
-
GPM-8213 - GW Instek
GW Instek GPM-8213 power meter is designed specifically for single-phase (1P/2W) AC power supply’s power measurements. Powerful features, including 4” TFT LCD, five-digit measurement display, 19 power measurement parameters, integral measurement function, high-accuracy voltage/current/power measurement capabilities, front/rear panel input terminals, and various communications ports, are to facilitate users with clear, convenient, and accurate power measurements.
-
SEL-735 - Schweitzer Engineering Laboratories, Inc.
The SEL-735 Power Quality and Revenue Meter passes accuracy requirements three times more stringent as the ANSI C12.20 Accuracy Class 0.2 standard. Advanced load profile trending, compatible with Itron® MV-90, DNP3, and Modbus protocols, ensures integration with practically any billing system. In addition to a full set of revenue metering features, advanced power quality monitoring will report costly system disturbances.
-
IPM-4 - FM SYSTEMS, INC.
The IPM-4 digital video level master is used to measure the signal quality of your IP video network. This low cost meter makes 6 different level measurements give you the assurance that your IP video system is working within specifications. It measures the output levels of both the camera and the recorder end of the system in dBm so you can check the near-end and far-end signal levels simultaneously.
-
Model 715B - Prostat Corporation
- Assess electrostatic fields or charge on objects- Measures up to ±19.99 kV at a distance of 1 inch- Accuracy of <±5% in both normal and ionized environments- Uses a chopper stabilized sensor- LED ranging lights for positioning the meter at the right distance- Zero function allows the display to be adjusted to zero (0)- Hold feature to lock the reading on the display- Low battery indicator on the display- 1-year limited warranty
-
MCR-5000 series - Matrix Technology Inc.
MCR5000 series is a multifunctional LCR precision meter used for testing various electronic components. Adopt 4.3-inch TFT LCD display, simple display, elegant layout. It is a high speed, wide band, 5 bit test resolution impedance measuring instrument with 40hz-200khz multipie frequency points and 0.1% accuracy, which can meet the requirements of component parameter detection in various occasions. Is a high - quality cost-effective tester.
-
Model 308 - OAI
Dependable and repeatable, The OAI Model 308 UV Intensity/Power Meter is precise, direct-reading instrument designed to measure UV light intensity. The Model 308 features detachable probes for use in the UVA, UVB and UVC ranges, plus a high speed serial port and is available with an optional software package that facilitates instant data logging of intensity mode, time, wave length, serial number and calibration due date.
-
EN100 - Extech Instruments Corporation
The EN100 is a Compact Hygro-Thermo-Anemometer with Light Sensor. 11-in-1 Environmental Meter for indoor and outdoor conditions. Built in light sensor measures light level. Auto-rotating display depending on selected function. Also measures Air Velocity, Air Flow, Temperature, Humidity, Wet Bulb, Dew Point, Heat Index, Wind Chill, Barometric Pressure and Altitude. Complete with built-in multiparameter sensors, wrist strap, and CR2032 battery.
-
LD-LBWM-A10 - Labodam
Benchtop Water hardness meterLD-LBWM-A10is equipped with large backlit LCD display, 2 to 5 points calibration with low to high concentration range. The calibration due reminder alerts user for calibration of the meter on regular basis. The System menu allows setting the 7 parameters like stability condition, auto-power off etc. It measure salts of calcium & other elements at mg/L, mmol/ scale which causes hardness water.
-
MO260 - Extech Instruments Corporation
MO260 is a Combination Pin/Pinless Moisture Meter which measures Relative Moisture in wood and other building materials using pinless technology plus % of Moisture in sheetrock and other materials using the direct pin method. Measurements are displayed on a digital LCD with backlighting and a tri-color LED bargraph. Pinless non-invasive measurement depth to 0.75" (22mm) below the surface. Complete with 9V battery, replacement pins, protective cap, and pouch case.
-
Teledyne Marine Impulse-PDM
Teledyne Impulse-PDM’s 5135/5175 optical connectors utilize proven standard ferrule technology and are available for multi-mode or single-mode operation.The connectors are manufactured in Titanium Ti 6Al-4V, which is electro-polished to remove surface contamination, thus improving resistance to corrosion. The engaging nuts are also manufactured in the same grade of Titanium and the threads are coated with a Nickel/PTFE composite coating to prevent galling. The connectors have been qualifi ed to 12,000 meter operating depth.
-
ED-205 - Standard Electric Works Co., Ltd
● Dimension：91(L) × 103(W) × 100(D)mm● Deflection Angle : 90°● Scale Length：Approx. 65mm ● Terminal： 4mm socket captive head, suitable for wire or pin-type test lead.● Material And Color： Acrylic resin meter cover, white scale plate, plastic stand in black.● Safety Standard： IEC/EN 61010-1 CAT Ⅱ 300V EN 61326-1 EN 61000-4-2 EN 61000-4-3
-
SVP Neon Equipment
A Bombarding A.C. Milliamperes Meter is one of the four instruments essential for proper luminous tube processing. This instrument monitors the level of bombarder current in milliamperes that is generated by the bombarder, through the tube being processed. It is necessary to accurately monitor the current for the tubing and electrode sizes used to ensure that the right amount is applied at the appropriate time. To do otherwise may cause damage to the electrodes, fluorescent coating inside the tube and adversely affect the glass structure.
