Showing results: 1411 - 1425 of 10608 items found.
-
DP0011A -
Keysight Technologies
The Keysight DP0011A is the 500 MHz model of the DP001xA Series differential active probes. These probes provide the superior general-purpose differential signal measurements required for many of today’s high-speed power-related measurements such as motor drives, automotive differential bus measurements, and high-speed digital system designs.
-
Truevolt Series -
Keysight Technologies
Truevolt digital multimeters (34460A, 34461A, 34465A, 34470A) enable you to get quick insights, measure low-power devices, and maintain calibrated measurements with Keysight’s measurement technology. Truevolt offers a full range of measurement capabilities with higher levels of accuracy, linearity, speed, and resolution.
-
MSR 500/3 CAR 4WD | VP 230037 -
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/3 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/3 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.
-
MSR 500/2 CAR 4WD | VP 230036 -
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.
-
RX-95 -
Resonance Technology
The system works based on the absorption of microwave energy by water molecules contained inthe x-rayed material. It is a non-contact, non-destructive method of instant measurement of water content - used for materials such as coal, flour, grain, cement, seeds, sugar, etc. Thanks to high measurement sensitivity (resolution greater than 0.01% of water content by weight), short measurement time (about 5 times/sec.) and repeatability of measurement - the system is suitable for continuous measurement of material moisture, e.g. on conveyor belts and its recording on a PC or using a 4-20 mA current loop.
-
Chroma 16502 -
Chroma Systems Solutions, Inc.
With a basic accuracy of 0.05%, Chroma 16502 offers a 0.001mΩ ~1.9999MΩ wide measurement range. It provides measurement range with 4 1/2 digits resolution. The fast measurement time is 65 ms. It suits component evaluation on production line. Pulsed test current output mode is used to reduce thermal EMFs affection on milliohm measurement. DC test current output mode is used to fasten measurement speed for inductive DUT. Dry-circuit test current output mode is used to measure such contact resistances where the maximum open-circuit voltage must be limited to 20mV.
-
VX2120 -
VX Instruments GmbH
The VX2120 is a high precision Digital Multimeter (DMM) for high performance measurements with 24Bit resolution. It provides measurements DCV up to 1,000VDC, ACV up to 1,000VACPeak and resistance (2 or 4-wire) up to 10MΩ. The internal microprocessor is equipped with flash memory for an fast and easy software update via the VXI-Bus. This will simplify new measurement functions to be downloaded. The VX2120 does support both True-RMS and Average-Peak AC-Measurements. For high precision AC measurements the VX2120 uses the "tracking technology". This feature allows high accurate AC measurements even at very low signal frequencies.
-
CCM-300 -
Opti-Sciences, Inc.
The CCM-300 uses a proven fluorescence ratio technique for chlorophyll content measurement at an affordable price. Readout is directly in chlorophyll content mg/m2, and measurement ratio.
-
Mitutoyo Corporation
arious kinds of measurement is achieved by upper / lower surface continuous measurement and measurment adjustable functionEquipped with new arm fixed by a magnet-type attach/detach mechanism
-
Process Instruments Inc.
Process Instruments calibrates a wide variety of test and measurement equipment. All calibration procedures are written, and most are automated, insuring reliability and repeatability of measurements.
-
Changzhou Applent Instruments Inc.
Is an intelligent measurement instrument with easy operation, low price, high measurement speed. Can be used for incoming inspection and fast sorting on inductance production line.
-
Arden Photonics LTD
*Improve measurement accuracy*Ensure stable launch conditions for multimode fiber measurements*Meet 85/85 launch conditions required in some aerospace applications.
-
GL100 -
Graphtec Corporation
*Easy measurement by multifunction input*Available the software for PC & Smart devices*Possible to check the data in multiple method*Reliable measurement with useful functions
-
TES Electrical Electronic Corp.
Wide spectral range. Excellent long term stability.Cosine corrected. Automatic transmission measurements. Select either power or transmission. Solar energy measurement.
-
TM191 -
T&M Tools Limited Co
TM191 series visual fault locator is used for the measurement in single mode or multi-mode fibers. It features a rugged design, a universal connectorand an accurate measurement