Magnetic Field Mapping
See Also: Magnetic Field, Magnetic Field Meters, Magnetic Field Probes, Magnetic Field Sensors, Magnetic Field Test
-
product
Magnetic Field Camera: mapping for MRI applications
MFC2046
MRI and NMR spectroscopy applications require a highly uniform magnetic field, within at most a few ppm. NMR is the only magnetic measurement technique capable of providing a field map with that degree of precision. Introduced 25 years ago, Metrolab’s NMR Magnetic Field Cameras have revolutionized field mapping for MRI magnets. They reduced acquisition times from hours to minutes, positioning errors to fractions of a millimeter, and they rendered human and drift errors negligible. Now, meet the latest generation NMR Magnetic Field Camera, the MFC2046! Map any magnet with the New generation of MFC probe arrays. Magnetometer Teslameter Gaussmeter
-
product
Magnetic Field Sensor
Vernier Software & Technology, LLC
The Magnetic Field Sensor can be used to study the field around permanent magnets, coils, and electrical devices. It features a rotating sensor tip to measure both transverse and longitudinal magnetic fields.
-
product
Magnetic Field Scanner
MAGNET-PHYSIK Dr. Steingroever GmbH
Magnetic field scanners measure the magnetic field around permanent magnets or magnetic systems. The results can be output as a colored 2D, 3D representation or as a table.
-
product
Magnetic Field Meter
MP - 2000
The new magnetic field meter MP - 2000 first used probes (tangential and Axialfeldsonden), in which an own microcontroller, the analog sensor signals are digitized and linearized directly in the probe. This new technique is extremely trouble-free and allows very precise measurements, especially at high magnetic field strengths, where Hall probes can not operate linearly.
-
product
Magnetic Field Tester
MS-440
This device recognises fast and simply magnetic fields generated by electric reels and permanent magnets.
-
product
Probes, Magnetic Field
EM-6880 | 9 KHz – 520 KHz
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
-
product
Relay / Magnetic Field Testers
PeakTech Prüf- und Messtechnik GmbH
Ideally suited for checking magnetic fields and the correct function of coils, e.g. Relays and solenoid valves. The magnetic field detector works without contact, so that opening the housing is not necessary in most cases. When a magnetic field is detected, the probe tip lights up permanently blue, with clocked relays in the same cycle as they are controlled. The function of the magnetic field detector can be checked before each measurement with the enclosed test permanent magnet.
-
product
Impulse Magnetic Field Immunity Tester
IMF61000-9
IMF61000-9 impulse magnetic field immunity tester is high performance test instrument which special designed for to do impulse magnetic field immunity test and fully meet IEC61000-4-9, EN61000-4-9 and GB/T17626.9 standards, also it come with high intelligent, high stable performance and easy operation characteristics.
-
product
Magnetic Field Testing
Response Dynamics Vibration Engineering, Inc.
As magnetic field consultants, we have been working with magnetic field issues for sensitive tools for many decades from cutting edge development of scanning electron microscopes (SEMs) to active cancellation systems for MRI tools, to site surveys for specification compliance, debugging, and tool Magnetic Field Sensitivity Testing.
-
product
Pressure Mapping
WIPER
Evaluate wiper blade force profiles and interface pressure distribution.
-
product
Magnetic Field Cancelling System
MR-3
3-axis magnetic field cancelling system for electron microscopes (SEM and TEM), electron and ion beam experiments, nanotechnology, biomagnetic investigations, etc. High reliability through rugged analog design. No tedious programming, no chrashs. More than 1000 MR-3 systems sold worldwide.
-
product
MAPS Core
An all-in-one core package includes the ADLINK products’ driver, device management utility-ACE and, PXI configuration setting utility
-
product
Magnetic Field Cancelling System
MK-1
Single axis magnetic field cancelling system for MRI scanners and biomagnetic applications. This system is used when the magnetic field sensor cannot be placed within the shielded volume. For example, in MRI applications the sensor is usually installed outside of the shielding room because of the MRI scanner's high fringe field.
-
product
Triaxial ELF Magnetic Field Meter
SK-8301
Accurate measurement by- True RMS- Built-in XYZ triaxial sensorFor 40Hz to 1kHz magnetic field measurement.uT and mG are selectable.MAX/MIN and Average measurements.Compact and easy-to-carry.Easy operation by only 3-keys.
-
product
Probes, Magnetic Field
EM-6882 | 20 MHz To 230 MHz
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
-
-
product
Three Channel AC Magnetic Field Signal Conditioner
TCM-1A
Macintyre Electronic Design Associa
The TCM-1 is a three-channel portable signal conditioner specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from either its internal batteries or the power line. It incorporates two sets of power line rejection filters, switch selectable for 50 or 60 Hz and the corresponding first four harmonics.
-
product
Damped Oscillatory Magnetic Field Immunity Tester
DOMF61000-10
DOMF61000-10 damped oscillatory magnetic field immunity test system included damped oscillating wave generator and single ring coil, it’s designed for to do damping oscillation magnetic field immunity test and fully meet IEC 61000-4-10, EN61000-4-10 and GB/T 17626.10 standards requirement.
-
product
Magnetic Field Sensors
Analog Devices magnetic field sensors combine integrated bulk Hall cell technology and instrumentation circuitry to minimize temperature related drifts associated with silicon Hall cell characteristics. The architecture maximizes the advantages of a monolithic implementation while allowing sufficient versatility to meet varied application requirements with a minimum number of components.
-
product
Magnetic Field Meters
A scientific instrument used to measure the strength and direction of a magnetic field.
-
product
Magnet Testing
m-axis
m-axis is a measurement system that can be used to characterize permanent magnets in terms of their magnetic specifications (magnetic moment and magnetization angle) with high precision. In addition to the four standard measuring ranges, the modular design allows the system to be adapted to customer-specific requirements. The measurement systems can be used for 100% in-line quality control via our m-axis I/O module.
-
product
Magnet Tester
MP
Computer aided measuring desk for automatic measurement of hysteresis loop of hard magnetic materials. Use pole pieces with integrated measuring coils, or J-compensated surrounding coils.
-
product
Magnetic Field Sensors
Our cylinder sensors for pull rod cylinders can be integrated into many applications. They are mounted with mounting brackets on cylinders with tie rods and DUO rails. The concept is suitable for the most common types of cylinders with any piston diameter. Features: contact-free detection of the piston position, tie rod Ø up to 17 mm, reliable switching behavior, wear-free, resistant to dirt, secure grip, easy installation.
-
product
Field Meter
AP 301 FULL HD
The AP301 FULL-HD is a field meter with total coverage of terrestrial TV bands, cable TV (CATV), 1st IF satellite and, if the relative option is inserted, the return channel 5-65 MHz.
-
product
Magnetic Field Logger Sensor
NUL-214
This is a very sensitive magnetic fields sensor. It can measure a very low level of magnetic fields such as the magnetic field of Earth.The logger sensor measures the magnetic fields in milli Tesla (mT).
-
product
Magnetizing Yokes, Magnetizing Coils
Recently in the motor industry, the decreasing the Cogging Torque, noise (vibration), and lost current, is required as the miniaturization, high-performance, and energy-saving abilities increase.
-
product
Magnetic Switches / Magnetic Sensors
BERNSTEIN offers electromechanical reed contact magnetic switches and electronic versions which operate according to the Hall and magnetoresistive principle.The electronic versions are characterised by their enhanced mechanical properties (extremely high resistance to vibration, shock or impact) and are not prone to wear in operation. Thanks to the use of only one single “active” component (reed contact), “traditional” electromechanical magnetic switches are extremely reliable in operation. The universal current capability and low procurement costs allow these switches to be used in a wide range of applications.
-
product
Probes, Magnetic Field
EM-6881 | 480 KHz To 30 MHz
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
-
product
Concrete Corrosion Mapping System
15620
Our Concrete Corrosion Mapping System (CCMS) can be used to satisfy the ASTM C-876 standard test method and the kit contains all equipment items that are needed to perform a corrosion survey on virtually all types of reinforced concrete structures, such as bridges, highway slabs and parking garages.
-
product
Field Meter
AP 201 Plus
The AP201 Plus field meter with total coverage of terrestrial TV bands, cable TV (CATV), 1st IF satellite and, if the relative option is inserted, the return channel 5-65 MHz.
