Showing recent results 496 - 510 of 1974 products found.
-
Senko Advanced Components
A fiber optic attenuator is a passive device used to reduce the amplitude of a light signal without significantly changing the wave form itself. This is often a requirement in Dense Wave Division Multiplexing (DWDM) and Erbium Doped Fiber Amplifier (EDFA) applications where the receiver cannot accept the signal generated from a high-power light source.
-
Senko Advanced Components
A fiber optic attenuator is a passive device used to reduce the amplitude of a light signal without significantly changing the wave form itself. This is often a requirement in Dense Wave Division Multiplexing (DWDM) and Erbium Doped Fiber Amplifier (EDFA) applications where the receiver cannot accept the signal generated from a high-power light source.
-
NANO-flex® - Particle Metrix GmbH
Nanoparticle Measurement Device for Particle Size Distribution with 180 DLS Dynamic Light Scattering. System for characterization of colloids by dynamic light scattering within a size range of 0.8 nm to 6.5 m. Suitable for material systems with concentrations from ppm up to 40% vol., depending on substance type. Minimum is 1 droplet.
-
CT102 - Etcon
Checks correct wiring for 15 or 20 amp, 120 VAC single-phase 3-wire receptacles. High visibility colored lights. Reliable electronic components, no mechanical failures. Easy-to-read chart explains light display. Compact size fits shirt pocket. Dimensions: 3" x 1-3/8" x 1-3/8".
-
Senko Advanced Components
A fiber optic attenuator is a passive device used to reduce the amplitude of a light signal without significantly changing the wave form itself. This is often a requirement in Dense Wave Division Multiplexing (DWDM) and Erbium Doped Fiber Amplifier (EDFA) applications where the receiver cannot accept the signal generated from a high-power light source.
-
Senko Advanced Components
A fiber optic attenuator is a passive device used to reduce the amplitude of a light signal without significantly changing the wave form itself. This is often a requirement in Dense Wave Division Multiplexing (DWDM) and Erbium Doped Fiber Amplifier (EDFA) applications where the receiver cannot accept the signal generated from a high-power light source.
-
Senko Advanced Components
A fiber optic attenuator is a passive device used to reduce the amplitude of a light signal without significantly changing the wave form itself. This is often a requirement in Dense Wave Division Multiplexing (DWDM) and Erbium Doped Fiber Amplifier (EDFA) applications where the receiver cannot accept the signal generated from a high-power light source.
-
708 - Summit
The 708 is an affordable combustion efficiency analyzer, CO analyzer, and differential thermometer for residential and light industrial applications
-
SF 100 - LMT Lichtmesstechnik GmbH
Flash meters for measurement of illuminance time response of rapid changing light sources (flashes, rotating beacons).
-
Shanghai MCP Corp
.Multi Test Voltage .Auto range .LCD background light .Data hold .INSULATION RESISTANCE TESTER
-
Digital 250 – Light Duty - Pyrometer Instrument Company
The Pyrometer Digital 250-LTDuty digital thermometer is a low-cost, light-duty, digital pyrometer temperature sensor. The digital thermometer pyrometer is ideal for temperature sensor measurement using thermocouple thermometer K type thermocouples. The hand held case is made from durable plastic, which is enclosed by a shock resistant rubber boot with a flip out rear bracket from stand up viewing. The thermocouple-input jack is a standard mini flat pin connector for easy thermocouple interchangeability. The Digital 250-LTDuty accepts either J or K thermocouple inputs. Instrument accuracy is +/- 0.3% reading. There is a choice of 14 different thermocouples to meet most process measurement applications.
-
ILX Lightwave
Arc lamp light sources have high ultraviolet and visible output with some prominent lines in the near infrared, which make them useful for many Spectroscopy applications. The small, bright arcs have significant advantages for collimation and intense irradiation. Please our Arc Lamp Guide or Deuterium Light Source Guide for additional information
-
PREMOSYS GmbH
Systems are designed for very fast, parallel and automatic testing of both the color and intensity of LEDs, displays, dashboard lights and other self-illuminators. The color checking system covers the entire spectrum of visible light from dark to the brightest LEDs and provides very precise color analysis and intensity detection with outstanding intensity detection and ease of operation.
-
Biophotonics Solutions Inc.
The Microscope Detection Unit (MDU) is designed to facilitate femtosecond pulse compression and measurement directly at the focal plane of a microscope, inverted or upright. It contains a nonlinear crystal for second harmonic generation (SHG) as well as other optical elements to separate SHG photons from the laser light and to couple the SHG light into a compact spectrometer via SMA-connected fiber.
-
FZ-10 - Panasonic Electric Works Corporation
FZ-10 Color Detection Fiber Sensors are equipped with three LEDs - red, green and blue - as their light source. This contributes to a long Sensor life and a high immunity against disturbances through ambient light. The RGB components of each detected color are processed digitally, thus the smallest differences will be detected by this Sensor. Even white and yellow can be distinguished.
