Showing results: 46 - 60 of 108 items found.
-
056-301 -
ELMA Electronic, Inc.
The 6U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane. With two coding switches on the front panel it is possible to set a constant current or load profile for +5V and +3,3V. For +12V and -12V the current will be set with two jumpers on the board.
-
056-377 -
ELMA Electronic, Inc.
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane. With two coding switches on the front panel it is possible to set a constant current or load profile for +5V and +3,3V. For +12V and -12V the current will be set with two jumpers on the board.
-
0001-011 -
VI Control Systems Ltd.
A general purpose interface board for Mircromint's Answer Man Junior. Jumpers select one of three communication interfaces (RS-232, RS-485, or fiber optic RS-232). 12 bit ADCs and DACs are added for higher precision AD conversions. Answer Man Junior is included with the board.
-
post4d -
PC Engines Gmbh
During power on self-test (POST), most PC BIOSes will write diagnostic codes to port 80h or port 84h (jumper selection). Use post4d to display these codes on a dual digit LED display. Additional LEDs indicate the status of the power supply rails. Convenient business card size.
-
VME-4514A -
Abaco Systems Inc
The VME-4514A Analog I/O (AIO) Board provides 16 high-quality analog output channels which can be programmed with on-board jumpers to operate in a variety of voltage ranges. Each output can source or sink 10 mA at ±10 V. For off-line testing, the analog outputs can be disconnected from the I/O connector.
-
SCIM5B -
Bee Instruments
BEE INSTRUMENTS offers cost- effective, isolated industrial signalconditioning modules. The SCIM5B analog modules are form, fit, and functional equivalents to similar products from other manufacturers. The product range includes a complete selection of backpanels, interface cables, racks, fuses, jumpers, power supplies, and other accessories.
-
Keystone Electronics Corp.
Today's high tech electronics require space saving, low cost methods for connecting and testing circuitry. Our complete line of Quick Fit terminals, Screw Terminals, Solder Lugs and Test Points and Jumpers are designed to meet the interconnect and testing challenges for electronic and electrical component termination points.
-
AF-FCT-100 -
Advanced Fiber Solutions
The FCT-100 is a bright visual light source for checking continuity or quickly tracking multimode fibers in networks to insure proper connections, a difficult task in larger fiber count systems. In addition, it can be used as a continuity checker to determine if jumper cables with connections or fiber on reels are in good condition or if installed fiber has been damaged.
-
RatMaster -
Array Solutions
- Jumper free configuration- Intuitive configuration software- RS-232, TTL and CI-V interfaces- Automatically generates Icom CI-V data stream from non-Icom radios- Configurable band limits- Built-in USB interface- Set default antenna per band- Field upgradeable firmware- Anodized aluminum case- Laser engraved panels
-
PAS 9715/AO -
Precision Analog Systems Co.
The PAS 9715/AO provides thirty-two, twelve bit analog voltage output channels on a 6U VMEbus card. VME systems with A16, A24, or A32 addressing are supported, and data writes of 16 or 32 bits can be used. Pluggable jumpers are used to configure the width of the address bus and the data bus width is specified by the instruction type.
-
RF Industries
Manufactured using industry standard low PIM cables terminated with RF Industries or other brands of connectors. Assembled in the United States for quick delivery. Jumpers are assembled from a wide variety of in-stock connectors and cables to meet system requirements for flexibility, low loss, low PIM, in-door/out-door, fire rating and electric performance.
-
327/328 -
Sensoray Co., Inc
Model 327 and 328 are bus-to-bus adapters that allow operating a PCI board from a PC/104+ card stack. They allow selection of important PC/104+ signals using jumper plugs, thereby avoiding the requirement of using hardwired settings. Model 327 aligns the PCI board parallel to the PC/104+ boards, while model 328 places it perpendicular.
-
VECTOR Electronics and Technology, Inc.
Universal (uncommitted) multilayer backplanes are designed for unique one of a kind applications requiring custom pin-out wiring from connector to connector. Each individual connector pin must be "assigned" by connecting to adjacent power or ground pins with wire or jumpers. Power or Ground input through a labeled series of power taps (screw terminals) along to top and bottom of the board.
-
Naprotek, LLC.
In standoff capacitors, SemiGen offers controlled dielectric thicknesses of +/- 12 microns, < 0.1 micron mounting surface finishes, and outline (L&W) tolerances of < 25 microns. We assure lot-to-lot repeatability and very attractive pricing. RF engineers requiring jumper mounts, bypass and tuning capacitor flexibility will find our wide selection of standoff capacitors convenient and reliable.
-
TE3200 -
TEAM SOLUTIONS, INC.
The TE3200 is a dual output programmable DC power supply designed for use in PXI/CompactPCI chassis. The TE3200 occupies a single slot and will utilize an external supply of 48VDC (provided). A separate srrew-terminal/power adapter board, p/n TE3202, provides connectivity for two 48VDC power suppies and screw-terminals and jumpers for voltage and sense selection and connection. The TE3202 is included with all retail purchases (not included with OEM purchases).