Showing results: 61 - 75 of 108 items found.
-
Teledyne Marine ODI
Junction boxes are used for complex power and signal distribution. The junction boxes have redundant mechanical barriers. The mechanical integrity of the junction box is verified during helium leak testing and hydrostatic testing of the jumper assembly. Thermal and pressure compensation is provided by the radially compliant hose or by purpose built bladder compensators, hose lengths must be sized according to the junction box internal dead volume.
-
TCT-2690PRO -
Tenma
LAN/length cable tester quickly and accurately tests network, telecommunication, cable and security systems for a variety of issues. Tests for open or short circuits, jumpers, cross or split pairs, continuity and wiring of cable patterns, cable identification and length measurement using included remote ID.
-
VIPC627-ET -
Abaco Systems Inc
VIPC627-ET is a 6U VME carrier card with four IP slots and extended temperature range. Two 50-pin, 0.1 inch flat ribbon cable connectors mounted in the front panel provide access to all IP I/O lines. Also, all I/O lines of 'IP D' are routed to VME P2 and 14 user selectable I/O lines of 'IP C' can be routed to VME P2 via a jumper field.
-
VI Control Systems Ltd.
All channels provide for voltage division ahead of transient suppression before going into the S&H ICs. Channels that are sampled and held use a common sample and hold pulse that samples while high and holds while low. Jumpers on each S&H chip allow buffering of analog signals where sample and holds are not required. An advantage to the buffers is that it provides a high input impedance for high impedance voltage dividers.
-
Alliance Support Partners, Inc.
Clock Divider is designed to divide high frequency signals, up to 2.5GHz, from 4 to 256 times. It will accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms. The clock division is controlled by 4 shunt jumpers. The circuit can be disabled and the divide by counter reset with 2 control signals. The on board regulator will accept voltages from 4.85 to 15.0V. The output is capable of driving 700mV Peak to Peak into 50 Ohms.
-
PCIextend 174 -
Sycard Technology
The PCIextend 174 extender card is a debug tool for 32-bit PCI designs. Designed as both an extender and debug tool, the PCIextend 174 supports both manufacturing and engineering needs. As an extender card the PCIextend extends a PCI card 2.5" above the host computer. Jumper blocks on all power supplies allow for current consumption or voltage margin testing. Multiple power status LEDs indicate 3.3V, 5V, +12V, -12V, VIO and VAUX.
-
104-AIO12-8 -
Acces I/O Products, Inc.
*Eight true differential inputs, or eight single-ended inputs optional*Programmable input ranges of: 0-5V, 0-10V, ±5V, ±10V*100KHz sampling rate*On-board pacer clock and counter timers*Four double-buffered analog outputs*Jumper selectable output ranges of: 0-5V, 0-10V, ±5V, ±10V*24 digital I/O lines, type 82C55 with change of state detect on port C, buffers on ports A & B*Flexible configurations to suit your needs
-
AX92321 -
Axiomtek Co., Ltd.
*Four or eight USB 3.0 ports*Four independent USB 3.0 host controllers*900 mA/1500 mA max. per port configurable via jumper settings*Compliant with USB 3.0 Rev.1.0 and Intel® xHCI Rev.1.0*PCI Express x4 interface*Operating temperature from 0˚C to 70°C*Supports Windows® 7/10*Supports each port’s power on/off via software settings
-
PCIextend 176/177 -
Sycard Technology
The PCIextend 176 and 177 extender cards are debug tool for 64-bit PCI designs. Designed as both an extender and debug tool, the PCIextend 176 and 177 supports both manufacturing and engineering needs. As an extender card the PCIextend extends a PCI card 2.5" above the host computer. Jumper blocks on all power supplies allow for current consumption or voltage margin testing. Multiple power status LEDs indicate 3.3V, 5V, +12V, -12V, VIO and VAUX
-
Alliance Support Partners, Inc.
he ASP-DCD-00 board is a high impedance input clock divider circuit. It is designed to provide minimum load to a clock source for frequency measurement. It accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms; it divides the input signal frequency from 2 to 256 times depending on shunt jumper selections on J3. The board requires 5VDC 500mA power source to operate. The output is capable of driving 5V TTL logic levels.
-
TE3202 -
TEAM SOLUTIONS, INC.
- Provides DC-coaxial-jack connectivity for 1 or 2 external 48 VDC power supplies- Provides screw-terminal connectivity for all sense, return, & output lines- May be directly connected to the HD-DB15 on the TE3200 front panel, or extended with a standard VGA extension cable.- Provided header pins for jumpering sense & return lines to channel output & return lines.- Provides a 2-pin header for jumper configuration with only one externally supplied 48VDC input (but, halves the maximum output current)
-
TMP102 (Qwiic) -
SparkFun Electronics
We all like to know the temperature, right? Well, with the SparkFun TMP102 Digital Temperature Sensor, we've made it just about as easy as it gets. Based on the original Digital Temperature Sensor Breakout - TMP102, we've added Qwiic connectors to bring this board into our plug-and-play Qwiic Ecosystem and added an address jumper instead of breaking out the address pin. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
SparkFun Electronics
The ATtiny45 and 85 are a couple of really cool little MCUs but did you know you can program them in Arduino? That's right, now you can shrink your Arduino projects down to "tiny size" by moving your code straight over to these small but capable ICs. The standard method for programming the ATtiny ICs involves a breadboard, lots of jumper wires and a hardware programmer, but David Mellis over at MIT Media Lab has simplified the process by laying out this handy USB programmer.
-
GM8019 + GM83001E -
UC Instruments, Corp.
The UC INSTRUMENTS GM8019 + GM83001E 1310/1550 nm dual laser source back reflection meter and power meter is a compact, direct display instrument for the convinent measurement of backreflection, insertion loss and power connector, fiber optic components, and system. With a single output port, the meter is very easy to use and ideal for fiber cable jumper manufacturers.
-
SparkFun Electronics
The PicoBuck LED Driver is an economical and easy to use driver that will allow you to control and blend three different LEDs on three different channels. By default, each channel is driven at 330mA; that current can be reduced by either presenting an analog voltage or a PWM signal to the board. Version 12 of the board adds a solderable jumper that can be closed to increase the maximum current to 660mA. The new voltage regulator also increased the voltage rating on the various components on the board, allowing it to be used up to the full 36V rating of the AL8860 part.