Showing results: 1 - 15 of 163 items found.
-
ROGA-Instruments
Impulse hammers are designed for frequency measurement of mechanical structures, such as mechanical mobility, mechanical damping and impedance.
-
Hyperlabs, Inc.
HYPERLABS triggerable impulse generators create precise high-speed pulses with 50 to 100 ps rise time. They can be triggered by input from antennas and other signal generator systems.
-
CTS-10350 -
EMC Partner AG
The CTS-10350 is an impulse generator with a current wave shape 10/350 μs at the output terminals. Dual outputs enable testing of 2 terminal devices and 3 terminal devices up to class 1. The generator impedance is 1ohm in dual output mode or 0.5ohm when both outputs are connected together.
-
MIG2412SPD -
EMC Partner AG
The MIG2412SPD is a impulse tester for testing SPD (Surge Protection Devices) in accordance with IEC 61643-1 and VDE 0675. Up to maximum 24kV/12kA making it suitable for testing Class I to III or in accordance with VDE Class A,C, D. The MIG2412SPD is a hybrid generator with a voltage wave shape 1,2/50 ìs at "no load" and a current wave form 8/20 ìs at short circuit for testing Class III (D) SPD connected to power line.
-
Avtech Electrosystems, Ltd.
Provides pulse widths (measured at the 20% rise timepoint) in the range of 130 ps to 2 ns, amplitudes as high as 100 Volts, with pulse repetition frequencies to 1 MHz.
-
MCH Instruments Co.,Ltd.
*coil testing for motor and transformer *judge quality by comparing wave difference *LCD display
-
GDCY -
HV Hipot Electric Co.,Ltd.
The impulse voltage generator is mainly used to the field of impulse voltage tests by lightning impulse voltage full wave, lightning impulse voltage chipped wave and operate impulse voltage wave for such test products as electrical instrument.
-
Shanghai Sanki Electronic Industries Co., Ltd.
Impulse voltage generator Impulse voltage generator is mainly used for test products such as power equipment to perform lightning impulse voltage full wave, lightning impulse voltage chopping, operating impulse voltage wave and steep wave impulse voltage test, to inspect insulation performance. The technical indicators comply with national standards and IEC standards.
-
MIG0624LP1 -
EMC Partner AG
MIG0624LP1 is a multiple impulse generator with four independent outputs each of 6kA and 1 Ohm source impedance. These are combined to deliver impulses up to 24kA. The impulses generated by this equipment are the 8/20µs and 10/1000µs current impulses. Typical applications would be testing of varistors, gas arresters and other surge protection devices.
-
SUG-CCITT-A -
Lisun Electronics Inc.
Impulse Test Generator SUG-CCITT-A (1a. 10/700us, 6KV, figure is according to N.1 in IEC60950-1:2005 Annex N). N.1 ITU-T impulse test generators.
-
SKS-255I -
Shanghai Sanki Electronic Industries Co., Ltd.
The impulse voltage generator SKS-255I is manufactured in accordance with the IEC60255-5 "Insulation Test of Electrical Relays" promulgated by the International Electrotechnical Commission. It measures the insulation coordination between relays and protection devices and performs impulse voltage tests.
-
RZF Series -
Shanghai Jiuzhi Electric Co., Ltd.
Resistive voltage dividers have very good response parameters. Therefore they are used for measurements for full and front chopped lightning impulses or impulses voltages with steep wave fronts, also in the special condition it can be used for measuring DC.
-
GDCL -
HV Hipot Electric Co.,Ltd.
The impulse current generator is used to inspect the capacity of electric equipment withstand strong impulse current.It is widely used in lightning arrester and shock wave anti-interference test of electric and electronic equipment under their running conditions and used in other research project.
-
IT-25B -
Clinton Instrument Company
While most military standards now favor high frequency spark testing over impulse spark testing, the IT-25B Impulse Spark Tester is available for use in some aeronautic applications that still specify the impulse method. The IT-25B meets the test requirements of military specifications MIL-C-13777E, MIL-W-16878, and NEMA standards for hook-up wire used in high temperature wire applications. This method is favored as an alternate to a wet dielectric test.
-
Weshine Electric Manufacturing Co., Ltd
Impulse current generator is mainly used to test the ability of electrical equipment to withstand strong impulse current, widely used in lightning arresters and electrical and electronic equipment in operation conditions of oscillation wave immunity test, can also be used for other research tests.