Filter Results:
Products
Manufacturers
Applications
Impedance
-
Product
Impedance Analysis
S96041B
-
Make impedance analysis measurements of Surface Mount Device (SMD) components on the E5080B vector network analyzer with 16198A-010 10 GHz SMD test fixture.
-
Product
Impedance Analyzer, 20 Hz to 10/20/30/50/120 MHz
E4990A
Impedance Analyzer
The E4990A Impedance Analyzer has a frequency range of 20 Hz to 120 MHz. The E4990A provides an industry best 0.045% (typical) basic accuracy over a wide impedance range, with a 40 V built-in DC bias source. The equivalent circuit analysis function supports seven different multi-parameter models and helps you to simulate your own equivalent parameter values of components.
-
Product
WavePulser 40iX High-speed Interconnect Analyzer
WavePulser 40iX Series
Analyzer
WavePulser 40iX is the ideal single measurement tool for high-speed hardware designers and test engineers. The combination of S-parameters (frequency domain) and Impedance Profiles (time domain) in a single acquisition with a deep toolbox provides unmatched characterization insight of high-speed interconnects.
-
Product
Standard 3.27 (93.00) - 8.13 (231.00) High Frequency Probe
K-50L-QG
High Frequency Probe
Bandwidth @ -1dB (GHz): 4.00Return Loss @ -20dB (GHz): 0.80Nominal Impedance (Ohms): 50Test Center (mil): 550Test Center (mm): 13.97Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 225Recommended Travel (mm): 5.72Overall Length (mil): 1,830Overall Length (mm): 46.48
-
Product
Overhead Line & Cable Impedance Test Sets
-
T&R Test Equipment Overhead Line & Cable Impedance Test Sets
-
Product
Audio Generator & Impedance Meter
MR-PRO/MR2
-
The Minirator MR-PRO provides a full set of analog audio signals including sine wave, pink noise, white noise, delay test signal, polarity test signal, stepped sweep and continuous sine sweep. Further, a set of wav-files, useful for system optimization, is stored in the internal flash memory. Add your own personal favorites to this set.
-
Product
N1.2 Calibration Kit
-
N1.2 Calibration Kit, Frequency Range: up to 1.5 GHz, Impedance: 50 Ohm Connector Type: N-type
-
Product
Impedance meters
-
Electronic components meters for circuit verification in laboratories, technical schools and technical support centres.
-
Product
NM-SF 50 N-Male to SMA-Female Adapter
-
NM-SF 50 Adapter, N-Male to SMA-Female, Frequency Range: DC to 18 GHz, Impedance: 50 Ohm
-
Product
Cable Fault Locator
TX2001
-
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3000m (10,000ft) 50, 75 & 100 ohm Selectable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
Product
Impedance Matching Pads
-
Surface mount and coaxial 50 Ohm / 75 Ohm impedance matching pads for CATV systems, broadband networks, test setups and more!
-
Product
Potentiostat/Galvinostat Electrochemical Instuments
-
- 16 bit DAQ card- 250 kS/s aggregate- 125 kS/s per channel- Step Impedance Spectroscopy- Electrochemical impedance spectroscopy (EIS) 0.01 – 10 kHz- 5-lead cable (3 electrodes, sense & ground)- LabVIEW EZware software- Free software upgrades. 1 year parts and labor warranty- EIS information
-
-
Product
Differential Probe
DP-35
-
*High Sensitivity, High Voltage Model .*35MHz/1600 Vp-p Max.*Input Impedance 8MΩ//2.5PF*x10, x100 Attenuator, Easy to Convert.*Separating Design(Standard No.114205) Convenient & Durable.
-
Product
Power Absorption Clamp
-
Beijing KeHuan Century EMC Technology Co,.LTD
Frequency Range: 30MHz-1GHz Typical Insertion Loss: 17 dB ± 4 dB Output Impedance: 50Ω Connector: N(f), 50Ω Maximum Current: 30 A
-
Product
Battery Impedance Tester
-
Is an ideal tester for automotive, UPS maintenance and telecommunication applications.
-
Product
High Voltage Probe
HVP-40DM
-
*DC 40KV CAT II Pollution 2.*2000MΩ Impedance.*3999 LCD display.*Accuracy 1.0% full range.*T.C. 100 ppm/oC*400V/4KV/40KV, 3 range.*Resolution 0.1V/1V/10V.*PEAK HOLD, Auto power off.*CE, TUV GS, UL, CUL, IEC1010
-
Product
Digital Multimeter
DM500MAX
-
The DM500MAX is designed for harsh environments with a watertight gasket as the seams rotary switch, an input terminal, and battery cover to keep out dust, dirt, and splashing. They can also take shocks and drops, work anywhere from indoor to outdoor, and special designed LoZ(Low Impedance) feature to prevent false reading caused by ghost voltages.
-
Product
Impedance Analyzers
-
The E4990A Impedance Analyzer with a frequency range of 20 Hz to 120 MHz provides an industry best 0.045% (typ.) basic accuracy over a wide impedance range, with a 40 V built-in DC bias source.
-
Product
Precision Impedance Analyzer
TH2851-015
-
Changzhou Tonghui Electronic Co., Ltd.
■ Test frequency: 10Hz-15MHz ■ High precision: using automatic balance bridge technology, four-terminal pair test configuration
-
Product
Impedance Monitors
-
Single channel impedance monitorA flexible frequency generator/analyzerSupporting external load/potentiostat - TDI Dynaload RBL488 series & XBL series - WonATech WEL Load - Other 3rd parties potentiostat/galvanostat
-
Product
Transducer Simulator
Model TS-16
-
Impedance: 350 ohms nominal. Output Ranges: Fixed rotary switch: 0 to 3 mv/v in 15 steps of .2 mv/v
-
Product
Special Purpose Instruments
-
The Mechanical Impedance Sensor simultaneously measures an applied, driving-point force and response acceleration of a test structure for determining parameters such as mechanical mobility and mechanical impedance. The unit consists of a precision, shear mode accelerometer and a quartz force sensor in a common housing. Installation is primarily facilitated at the structural excitation points, in series with a stinger and vibration shaker.
-
Product
Micro Coax, Contact, Receiver, RG316
610140101
Coax Contact (ITA)
Primary mating contact 610141101. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC to 3 GHzVSWR 1.22 @ 3 GHzInsertion Loss – √f(GHz) x .06 dBDWV 800 V RMSContact Resistance 6 mOhms center/4 mOhms outerCable Specifications RG316Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
Product
Impedance Measurement
CITS880s
-
Finer geometries and thinner copper can present a challenge for fabricators measuring impedance on leading edge PCBs. The CITS880s answers that challenge with the introduction of Launch Point Extrapolation (LPE). LPE extrapolates the TDR response back to a point close to the start of the transmission line effectively allowing to users more accurately to measure the instantaneous or incident impedance of the line.
-
Product
Antenna Impedance Converter
-
The low noise impedance matching equipment has a high impedance input with minimized capacity. With the 50 Ω output it can be used with common EMI receivers or spectrum analyzers to measure the emissions received by an antenna on a vehicle.
-
Product
Impedance Analyzers
-
A/D converted input signals undergo discrete Fourier transform (DFT) to calculate complex impedance values and obtain parameters and characteristics specific to the DUT, such as its capacitance, inductance and quality factor. Original NF algorithms are also applied to allow equivalent circuits made up of R, L and C along with the constants for those circuits to be estimated from the complex impedance spectrum obtained by sweeping the frequencies.
-
Product
Line Impedance
KIT
-
The Line impedance kit is composed of two modules, STLG and STSG. The kit is meant to be used with STS 5000, STS 4000 and eKAM in order to perform Line Impedance test.
-
Product
Precision Impedance Analyzer
TH2851-050
-
Changzhou Tonghui Electronic Co., Ltd.
■ Test frequency: 10Hz-50MHz ■ High precision: using automatic balance bridge technology, four-terminal pair test configuration
-
Product
Benchtop LCR Meter
6365
-
Test Frequency 10Hz-200kHz. Output Impedance 100Ω. 7.0" TFT, 800×480 color screen. Basic Accuracy ±0.05%. Using Graphical Analysis by PC Link. Support RS-232、Handler、LAN、USB Host 、Handler、GPIB.
