Showing results: 256 - 270 of 587 items found.
-
R&J Measurement
Single Sheet Tester (500 x 500) mm is designed to measure dynamic magnetic properties of the electrical sheet according to IEC 60404-3 Standard. Single Sheet Tester (500 x 500) mm could be cooperating with following equipment designed to measuring soft magnetic properties:
-
ProfLine Series -
Teseq AG
The Teseq ProfLine system is a complete and cost effective Harmonics and Flicker measurement test system which compiles to the latest IEC/EN standards, including IEC 61000-3-2 and IEC 61000-3-3. The programmable power generation capability of up to 45 kVA (90 kVA and 145 kVA sources comprise multiple 45 kVA units) provides more than ample power to cater for a wide range of Equipment Under Test (EUT).
-
ACMAS Technologies Pvt. Ltd.
For testing various size solar panels WIEBER designs and manufactures Solar Panel Test Chamber. The test are to be performed according to various standards of ASTM, IEC, UC etc. Solar panels need to pass environmental tests as per IEC and other standards requirements to prove their long term performance and resistance to temperature and humidity extremes. Solor Chamber also known as Solar Photovoltaic Testing Chamber and PV Module Test Chamber.
-
Hybrid -
Hilo Test
Surge pulses occur due to direct or indirect lightning strikes in a circuit or by switching transients caused by switching inductive loads or short circuits. This leads to currents or electromagnetic fields causing high voltage or current transients. Surge voltages and currents can reach several thousands of volts and thousands of amperes. Our following Surge generators simulate these disturbances for all the necessary level in accordance with IEC / EN 61000-4-5 and IEC / EN 60060.
-
SE-04 -
KILTER ELECTRONIC CO.,LTD
Least affected by external stray magnetic fieldJaw size:Φ6.8mm,large 3 3/4 digits LCDThe minimum resolution is 1mAData hold,peak holddiode &continuity testcapacitance testAuto power off,sleep function to save batteryDesigned to meet international safety standard IEC 61010-1 CAT.III 300V
-
National Technical Systems
Ingress Protection testing, or IP testing, tests a product’s ability to protect against “ingress,” that is, the infiltration of water, dust and foreign objects. Some of the standards related to IP testing are MIL-STD-810 (Military), RTCA/DO-160 (Radio Technical Commission for Aeronautics), and IEC 60529 (International Electrotechnical Commission).
-
CX-IPX34C -
Shenzhen Chuangxin Instruments Co., Ltd.
1.Rain Spray Test Chamber is designed according to the standards of IEC 60529-2001 & GB 4208-93 & GB10485 (Enclosure protection level). It is mainly used for electronic products to do the waterproof test of the second characteristic number 3 / 4. The appliance meets the test requirement of IP grade IPX3/IPX4.
-
Iwasaki Electric Co., Ltd.
Complies with IEC60904 Class A solar simulation standards.Up to 100ms of effective irradiated time is achieved. Through our proprietary filter technology, spectral concordance conforms to IEC / JIS Class A standards.Three systems provide a wide selection to meet your panel size, floor space, and performance requirements.
-
TDK RF Solutions Inc.
TDK Test Services offers testing to domestic and international EMC test regulations, including IEC, ISO, CISPR, and SAE. Test services are offered in our 3m semi-anechoic chamber, 3m fully-anechoic chamber, 10-meter open area test site, and our shielded conducted test chamber.
-
Techsquare -
Techimp HQ S.r.L
New IEC standards, IEC 60034-18-41 and IEC 60034-18-42, have been issued to define the procedures for testing partial discharge inception voltage and the long-term performance (endurance) of Type I and Type II insulation systems used in rotating machines fed from voltage converters. Voltage impulse generators are required at least to test turn insulation, but they would be recommended for any testing under power electronics supply because of their capability to simulate the real electrical stress conditions. More generally, any type of electrical insulation system when subject to impulsive voltage waveform during life should be carefully evaluated in terms of partial discharge and endurance behaviour. This is why voltage impulse generators able to provide impulses with controlled amplitude and frequency are needed to face this new testing challenge.
-
Dewesoft d.o.o.
The Dewesoft power quality analyzer can measure all the power quality parameters according to IEC 61000-4-30 Class A. In comparison to other power quality meters ours are able to do more detailed power quality analysis. Raw data storing, behavior at faults, calculation of additional parameters, etc.
-
MicroStat Laboratories -R.E.T.S.
We utilize the relevant test methods and standards set forth by the ESD Association, ANSI, ASTM, NFPA, IEST, IEC, ISO, or our clients’ in-house specifications. ESD testing is performed in-house; other testing can be arranged through sub-contractors with interpretation of results performed by experienced contamination control experts..
-
ISIO 200 -
OMICRON electronics
ISIO 200 is a simple and versatile binary I/O terminal with IEC 61850 interface. For communicating with CMC test sets and real-time message exchange with peer devices, the fast GOOSE messaging is used. By using Client/Server communication, ISIO 200 can be integrated into Substation Automation Systems (SAS) and communicate to a station controller.
-
M-3000 -
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High accuracy analog display with strong taut band meter.*Meter lock function.*AC current, AC/DC voltage and resistance measurements.*Conform to IEC safety requirements.
-
Shanghai Pubang Sensor Co.,Ltd.
1.Non-contact position detecting,non-wear,high-reliability2.Clear visible indictor design,easy to estimate the working state3.Various type of Sensor,diameter spec.from Φ4 to Φ34,housing length,from ultra-short,short to standard type4.Equipped cable and connector,easy to maintain5.Protection class IP67(IEC)