- Taylor Dynamometer, Inc.
product
Water Brake Chassis Dynamometers
Chassis water brake dynos (also known as hydraulic dynamometers) can be operated continuously to resolve overheating, fuel mileage and drivetrain issues. Taylor’s eight models accommodating 50 to 1,100 hp at 40 mph enable testing of single-axle diesel pickup trucks, RVs and buses up through the largest tandem-axle on-highway trucks and buses. Tap into our deep product and applications knowledge to help you choose and make the most of the right water brake system for current and future needs.
-
product
Turbine Flowmeters with Analog Output
CT600R, CT800R Analogue Series
High accuracy turbine flow meters with built-in loading valve and analogue output, for use with hydraulic fluids. Flows up to 800 lpm (210 US gpm).
-
product
Hold Open Rods
TRIUMPH is a recognized provider of telescoping hold open rods as well as fixed-length struts. These products range from simple rods to complex assemblies with single- or dual-action release collars, hydraulic damping in one or both directions, and fixed mono balls, or universal joint fittings. These products are mainly used to keep fan cowls, radomes, doors, thrust reversers, and maintenance panels in the open position.
-
product
Vortex Flowmeters
The robust design of ABB’s vortex flowmeters provides high performance and reliability in liquid, gas and steam measurements. Equipped with digital signal processing (DSP) and advanced filtering techniques, these innovative flowmeters from ABB allow excellent flow signal detection and provide measurement immunity from the effects of hydraulic noise and pipeline vibration.
-
product
Bi-Directional Digital Hydraulic Testers
DHT302, DHT402 Series
The most popular sizes of digital hydraulic tester. Measure flow, pressure, temperature & speed. Flows up to 400 lpm (100 US gpm).
-
product
Hydraulic Hose Assemblies, 15,000 psi, US Army
9801B Tester
The 9801B hydraulic hose tester is utilized by the U.S. Army for high pressure testing of hydraulic hose and tube assemblies as well as any component testing requiring test pressures up to 15,000 psi. Enhanced safety for operating personnel is achieved by utilizing the optional 8801HT integral test chamber which was designed specifically to fit to all our 8801B and 9801B testers.
-
product
Portable Hydraulic Testers
Flo-tech portable hydraulic testers simultaneously measure the flow rate, temperature and pressure of hydraulic fluid. Flow rates are derived from an internal turbine meter assembly. These units were designed for testing pumps, valves, cylinders, motors, hydrostatic or power shift transmissions and power steering systems in both mobile and stationary applications. When used in a preventive maintenance program, untimely or catastrophic repairs are minimized. Three families of testers are available to provide operators with the perfect solution that fits their needs, each quipped with a carrying handle to improve portability.
-
product
Hydraulic Vertical Shock Test System
KRD10 series
KRD10 series full-automatic hydraulic shock test system is used to measure and determine the impact resistance of products or packaging, and to evaluate the reliability and structural integrity of products in a shock environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, trapezoid wave and other waveform shock tests to achieve the shock wave and impact energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
product
Hydraulic & Pneumatic Pressure Sensors
One of the toughest applications for pressure sensors is measuring high pressure, repetitive pulses, such as those encountered in hydraulic applications. However, our pressure sensors are designed to continuously measure repetitive pulses during applications such as hydraulic cylinder “torture” testing or diesel fuel injection. Ordinary diaphragm-type sensors usually fatigue quickly in such applications.
-
product
Engine Dynamometers
Taylor’s engine dynamometers deliver the best overall value by driving productivity, ensuring uptime and bringing you rapid return on investment. We offer a variety of engine dynos including hydraulic (water brake), eddy current, AC, portable and small engine dynos. We even offer mobile test centers and engine dynamometer accessories. Search below to find what you’re looking for, or give us a call today.
-
product
Pressure Products
Tel-Tru® Manufacturing Company
Tel-Tru pressure gauges are available in a wide variety of dial sizes, accuracies, pressure ranges, and case configurations, for the various requirements of industrial and process instrumentation. Rugged features make the line of stainless steel gaugesa top choice for process, power, hydraulic and OEM markets. All Tel-Tru pressure gauges meet ASME B40.1.
-
product
Economical Hydraulic Manual Universal Testing Machine
WEW-D Series
Jinan Testing Equipment IE Corporation
WEW-D series hydraulic manual UTM is suitable for testing tension, compression and other strengths of various metallic or nonmetallic materials with high strength. The hydraulic manual UTM is capable of testing the characters of materials on physical & technology properties. As a manual control & economical UTM, the hydraulic manual UTM is with reasonable and reliable configurations (load cell or pressure transducer, extensometer, photoelectric encoder, servo motor & driver, standard...show more -
product
Hydraulic Test Systems
Genuen specializes in hydraulic test stands, including component tests, pumps, motors, valves, actuators, fatigue, load frames, and burst testers. As an industry leader in custom test systems, we focus on hydraulic solutions that leverage off-the-shelf technologies for mechanical subsystems and components. Our hydraulic test equipment has been deployed in aerospace and defense, automotive, industrial, commercial, and many other industries.
-
product
Propeller Meters
Measures accurately over a flow range of 10:1 or greater.± 2% of rate accuracy, guaranteed by certified wet calibration at three test points in.Sparling’s National Institute of Standards and Technology (NIST) traceable hydraulic flow lab.Sturdy cast or fabricated steel construction.Operating temperatures are over 100° F(unless higher temperature construction is specified).Suspended solids are over 0.5% of volume.Easily maintained with standard tools.Registration can be furnished in any standard Engineering Unit.
-
product
Flow Measurement for Liquids
We provide reliable flow measurement devices for clean, slight and heavily polluted media as well as a very wide variety of sensors. Our hydraulic flow measurement systems as well as our radar and ultrasound-based flow measurement systems are supplemented by hydrostatic or ultrasonic level measurements.
-
product
Hydraulic Calibration for Load Cell
HLCS-10000
Jinan Testing Equipment IE Corporation
The Hydraulic Calibration System is specially designed for the calibration of load cells with higher capacity. The Calibration for Load Cell can calibrate the load cell within +/-1%.
-
product
Deadweight Testers
AMETEK Sensors, Test & Calibration
We provide the world’s only ball-type deadweight testers, where the ball and weights float on a thin film of air, which is virtually frictionless. This design eliminates the necessity to rotate the weights during testing, and allows the user to concentrate on the instrument itself. Our testers are engineered to offer user-friendly, safe operation, in the field, or in a lab. Both pneumatic and hydraulic testers are available.
-
product
Franklin Tester
Model FT1
The Franklin tester FT‐1 is designed to measure the surface insulation resistivity of electrical steel sheet according to the ASTM Standard A717 and IS:649. This test method is suitable for quality control in the application of insulation coating. For ease of testing FT‐1 automatically set 300 PSI pressure on the sample by the inbuilt hydraulic unit and it is capable to set the desired test temperature of the platform. Then the regulated supply of 0.5V gets on and the current flowing through the insulation get measured. The calculated insulation resistivity will be displayed on graphics LCD display and as well as on printed report via thermal printer.
-
product
Auto Bursting Strength Tester
TF142A/B
TESTEX Testing Equipment Systems Ltd.
Auto Bursting Tester, to determine the bursting strength of fabric, woven or knitted fabrics, non-woven, paper and board by the Application of hydraulic load under a rubber diaphragm of a specific area.
-
product
VXI Module
VDSP-31
The VDSP31 is a VXI based, multi-channel data acquisition system and digital servo control module. The VDSP31 offers a complete solution for high performance closed loop applications. The VDSP31 has been designed to solve specific problems related to the control of hydraulic actuators. Signal conditioning modules can be combined on a per channel basis to configure the VDSP31 for load or displacement feedback.
-
product
Systems
Walter Stauffenberg GmbH & Co. KG
Custom-design and ready-to-install hydraulic pipe, tube and hose assemblies from port to port
-
product
Pressure Manometer
This product is widely used in measuring fan pressure,wind speed,oven pressure,and hydraulic system. This product can also be used in controlling the gas ratio in combustion and valve control and monitoring the blood pressure and breath pressure with other medical devices
-
product
Compact Hydraulic Vibrator Force Simulator
JF Series
The JF Series Force Simulator was developed with the emphasis on light weight, compact size and ease-of-use as a general-purpose, compact jack for the Servopulser system. Testing systems installed with the Force Simulator can easily perform endurance, fatigue and simulation tests on small structural members and various other structural members, which helps improve the logical design and reliability of products.
-
product
Compression Testing Machine for Special Purposes
Jinan Testing Equipment IE Corporation
These compression testing machined are suitable for testing the compression strength of components or structural material such as concrete, steel, brick, rubber pad, etc. These compression testing machines feature large test space and double actions. Hand operate, analog dial or monitor. Hydraulic servo with computer control.
-
product
Pressure Comparators
AMETEK Sensors, Test & Calibration
Our high-pressure, hydraulic pressure comparators are portable, self-contained, hydraulic pressure generators for calibrating pressure gauges, transmitters, sensors, and safety valves. They are much faster than deadweight testers and most automated pressure controllers; and it’s so quick and easy to use, it’s ideal for calibrating those low cost gauges that are often overlooked for ISO9000 compliance. Each pump is available on its own, or in one of our complete ready-to-use pump systems.
-
product
Accumulator Charging Kits - (Europe)
The Parker Charging kit is an indispensable instrument for checking, adjusting or filling nitrogen into most of the hydraulic accumulators available on the market.
-
product
Reservoir, Hydraulic, 5 gallon
9901-101-05
The 5 gallon stainless reservoir can be combined with one of our hydrostatic test pumps or a complete hydrostatic test system when using water, any petroleum based hydraulic fluid or synthetic hydraulic fluids such as Skydrol.
-
product
Sensors for Mobile Machines
*Inclination sensors with CAN or analog interface*Inductive sensors with high protection rating*Pressure sensors with a robust measuring cell for mobile hydraulics*High shock and vibration resistance*Wide operating temperature range
-
product
Network LDT
AMETEK Sensors, Test & Calibration
The Network LDT is available in two different package styles; the 953N is our Rod Style package that is suitable for installation into hydraulic cylinders and our 957N Brik Low Profile Style package that incorporates the same electronics but is housed in an aluminum style extrusion.
-
product
Electric Servo Motor Type 1 Axis Vibration Tester
In Addition, The System Configuration Requires At Least 3 Main Units, A Control Panel, And A Controller, And Does Not Require Hydraulic Units Or Blowers. The Exciter Can Perform Standard Tests And Performance Tests Required For Automobile Seats Based On An Electric Servomotor Type Multi-Axis Vibration Tester.
-
product
Geotextile Water Permeability Tester
TG010
TESTEX Testing Equipment Systems Ltd.
Geotextile Water Permeability Tester, to determine the constant-head water flow capacity (water permeability) within the plane of a geotextile or geotextile-related product, is measured under varying normal compressive stresses, typical hydraulic gradients and defined contact surface.