Harness
A multi-routed assembly of connectors, wire and cables.
See Also: Cable Assembly, Harness Test, Test Harness, Wiring, Wire, Connectors
-
product
Wire Harness Tester
NX Pro
The Dynalab NX Pro Wire Harness Tester is a low-cost, feature-packed, stand-alone continuity tester with a maximum capability of 512 test points. The flexibility of the NX System allows each program to perform multiple tests, display custom messages or sounds, and analyze the results of a test or an input to "decide" which operation to perform next. The NX Pro Tester has 1.3Mb memory capacity for program storage and is compatible with Printers, Scanners, and all other Dynalab NX System accessories.
-
product
USB Type-C Test Fixture | CB26U | Cable Harness Tester
A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test.
-
product
Sea Water Immersion Test Device
Guangdong Bell Experiment Equipment Co.,Ltd
Sea Water Immersion Test Device Relevant standards requirement:Test Object: Battery storage pack or system.The test object connects all the wiring harness, connector and other parts according to the whole vehicle connection mode. Select one of the following two methods to operate test at the room temperature.Immerse the test objects (in the direction of real vehicle assembling) into 3.5% NaCl solution (mass fraction, simulated under normal temperature water composition) for 2 hours. The water depth is to be sufficient to completely submerge the test objects.Test objects according to GB/T4208-2017 part 14.2.7 test method and test process.
-
product
SafeBloc
A SafeBloc is an accessory device, which can be used with other test equipment, as an adapter, to connect and test power cords and wiring harnesses for production testing purposes, prior to installation into equipment. Such testing would include Hipot and continuity testing of the power cord or wiring harness. The SafeBloc allows the bare wires of a power cord or wiring harness to be connected to the test equipment via clips inside the enclosure. Power can only flow through the device once it is...show more -
product
1' Harness, 50-Pin Male D-Sub Connector
GT97108
1' harness, 50-pin male D-sub connector on both ends.
-
product
1' Harness, 78-Pin Male D-Sub Connector
GT97104
1' harness, 78-pin male D-sub connector on both ends
-
product
Ada Embedded Software Test Solution
VectorCAST/Ada
An integrated software test solution that significantly reduces the time, effort, and cost associated with testing Ada software components necessary for validating safety- and mission-critical embedded systems. VectorCAST/Ada parses your source code and invokes code generators to automatically create the test code (stubs and drivers) required to construct a complete, executable test harness.
-
product
Cable and Harness Tester
CHT
The Cable and Harness Tester (CHT) provides multiple testing capabilities for up to 300 connector/harness test points. Test capabilities include DC Insulation Resistance (IR), DC and AC Dielectric Withstanding Voltage (DWV), and 2-Wire and 4-Wire Continuity.
-
product
Full Performance and Flexibility on ECIS 8 Well Arrays
Sciospec ECIS Adapter
The ECIS CULTUREWARE 8 well arrays are a very common choice for a broad range of impedance-based cell experiments like cell groth, cell migration, wounding/healing, barrier function, tox-screening, adhesion and proliferation studies. With the Sciospec ECISadapter you can bring your ECIS experiments to the next level: more speed, higher resolution, more possibilities. Harness the full power of Sciospec impedance analyzers on your existing ECIS arrays. The ECISadapter just plugs into compatible Sciospec impedance analyzers like the ISX-3 and you´re good to go.
-
product
Harness Design and Manufacture
When designing an underwater cable harness, there are some factors which need to be considered, and we have produced the following list as a guide for customer information:Component considerations:- Electrical requirements- Mechanical considerations- Quality requirements- Reliability- Design redundancy (contact count)- Connector selection (type and form)- Locking requirements- Backpotting requirements- Waterblocking in moldings- Cable specification- Cable jacket material and compatibility with e...show more -
product
LXI High Voltage Matrix 2-Pole 100x2
60-310-102
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing. The 60-310 is designed in accordance with the LXI Standard 1.4 and is supplied in a 2U high, full rack width case with 500mm depth.
-
product
Cable Harness EM Solver
MHARNESS
Electro Magnetic Applications, Inc.
MHARNESS to Complete the Last Mile of EM Coupling Simulation Traditionally, electromagnetic effects simulation has focused on the transients induced on the overall cable bundle of complex systems. MHARNESS is a transmission line solver that reveals the EM transients on the most critical element of systems: the pin interface to electronics systems. Now, EMA3D and MHARNESS can co-simulate in one self-consistent simulation.
-
product
CableEye 4-Wire Calibration Verification Board | Cable & Harness Testers
CB52
The CB52 is intended for periodic calibration verification of the Kelvin 4-wire resistance measurement module – an optional, add-on module that may be purchased with any new hipot system, or added to an existing high voltage tester as an upgrade.
-
product
Solderability Tester
ZHX-35
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008/IEC60851-4; Inspection standard: JB/T4279.14-2008Used to detect the self-solderability of enameled round wires and wire harness;Set variable temperature range and automatically maintain constant temperature;Under mechanical driven, samples would be withdrawn by the action of automatic insertion and lateral movement, free from vibration and noise;
-
product
Switch Probes
A switch probe is designed primarily for “presence/ electrical” test applications such as detecting the absence or presence of contacts within a wire harness connector. In this case, the switch probe provides electrical interconnection and verifies the connector has been manufactured properly. If contacts are missing or out of place, the part is rejected. If all the contacts are in place, the part is accepted and an electrical test is performed, verifying the electrical integrity of the connector and the wires within the harness.
-
product
Exhaust Gas Thermocouple
LM2500 T5.4
AMETEK is the original OEM for the T5.4 EGT. We supply the L44830P01, L44830P02 and L44830P03 probes for use on the LM2500, LM2500+ and LM5000 gas turbines. In addition to the EGT, we also provide rigid harness, T3 probes, cables and flexible harness for these engines. Ensure you get the highest quality by selecting OEM qualified parts to keep your engine running reliably.
-
product
Modular Test System
A modular test system, RTS (real time scanner) provides instant test results with minimal interface cables to check wiring during installation.It tests wire harnesses in real time using our micro switching technology, reducing the need for high cost interface cables by around 90%. an innovative best-in-class solution for FAL testing, RTS also offers many benefits for wire harness and sub-assembly manufacturers.
-
product
2100Vdc Screw Terminal Connector Board | Cable & Harness Tester
CB29H
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with four 16-pole screw terminal blocks, the board addresses high voltage (HiPot) testing to 2100Vdc/1200Vac. Of particular interest to the harness testing market, the CB29H is also available as a transition board variant (CB29AH). The CB29H and CB29AH boards are high voltage versions of the CB29 with the high voltage traces running on inner layers to afford additional safety, and protection from contamination.
-
product
Rotary-Torque Transducers
Standard on-board kits include: wireless electronic torque transducer-equipped driveshaft yoke, tail-shaft pickup coil, wireless interface module, DYNOmite handheld data-acquisition computer, AC power supply, data wiring harness, and protective carrying case.
-
product
PXI 24 Channel High Voltage Multiplexer
40-320-101
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
product
Metal Thickness Tester
Multigauge 5500 Waist
Mounts onto a belt or chest harness for hands free use. Bright LED display. Top display for convenient viewing.
-
product
Pull tester for security testing
SAFOR 2000
The Safor portable tester is an accurate unit, designed for testing the pulling force of fixings prior to being put into service. Easily prevent accidents by testing on site the fixings to install end brackets and safety harness eyebolts.
-
product
Smart Bench Essentials Digital Multimeter
EDU34450A
The Keysight EDU34450A is a modern benchtop digital multimeter (DMM) that is part of the Keysight Smart Bench Essentials (SBE) Series of four unique instruments that harness one powerful graphical interface to connect, control, and capture measurement data. It features 5.5 digits of resolution and up to 110 readings/s measuring rate for speed-critical tests
-
product
7 Spade Pin Circuit Tester / Maintenance Kit
#8028
Innovative Products of America
Test, clean and restore 7 spade pin connections.The tester will verify that the tow vehicle is sending proper signal to the connector, while accompanying cleaning tools will remove corrosion, and verify proper pin size on both male and female truck/trailer plugs. For use with 7 spade connectors. Quickly tests, cleans and repairs truck and trailer connectors Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardPatentedKit Includes: #7893: 7 Spade Pin Circuit Tester, #8023: Connector Cleaners, and #8030: 2 ml DeoxIT Cleaner
-
product
PXI 16x SPST High Voltage Reed Relays
40-310-101
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
product
Portable Tester
ECAD System 2002
The ECAD System 2002 is a portable, ruggedized tester that can be used for troubleshooting and condition monitoring of installed circuits, cables and wiring harness. The ECAD tester is a combination of traditional electrical measurements, a database for storing test results, and data analysis software. This powerful combination allows a user to evaluate the condition of all circuit components in a logical and straightforward manner from one end of the circuit.
-
product
Software Development
In support of system, test and our tooling design, our software development team is ARC’s primary advantage in providing the superior performance in hardware (electrical), mechanical and software cohesiveness. The software team at ARC literally brings all of it together.Whether you want to leverage one of our standard platforms, such as TestCentre or harness the power of the process editor in our PVS software to build up your custom workflow, most customers are impacted by the power and scalabil...show more -
product
ATE & Test Systems
Data Patterns' core business for over 20 years has been the development of Automated Test Equipment for critical aerospace requirements. Data Patterns developed a Multi Programmer with associated test automation software in 1994. Christened the DP-800 this product was adopted for the implementation of test rigs for Navigation Platform Test Benches, Engine Test Bed Automation, Cable Harness Test Systems, etc. This product was effectively utilized in the development of test benches required by Ind...show more -
product
Pin-Mapping for Custom Connectors, Test Fixtures, UUTs | Cable & Harness Testers
PinMap™
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester.