- Advanced Telemetrics International
product
Band-On Telemetry System
Advanced Telemetrics International
The ATi Band-On Telemetry System transmits real-time sensor data from a rotating shaft while the system is running. The system consists of one or more rotating signal conditioner/ transmitter modules with battery pack and a stationary receiver. Rotating transmitters are available to interface with most any type of sensor including strain gages, thermocouples, thermistors, RTDs and accelerometers.
-
product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1.5Ω to 1.81kΩ
40-251-022
The 40-251-022 is a programmable resistor module with 4 channels which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI 5W Programmable Resistor Module, 1-Channel, 1.5Ω to 3.55kΩ
40-252-123
The 40-252-123 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 3.55kΩ with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI 2.5W Programmable Resistor Module, 1-Channel, 2.5Ω to 395kΩ
40-251-142
The 40-251-142 is a programmable resistor module with 1 channel which can be set between 2.5Ω and 395kΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Precision Low-Loss Multiplexers
Maury’s line of diplexers (DP-series) and triplexers (TP-series) are designed for applications which require combining/ splitting signals at or around harmonic frequencies (nFo) and are connectorized for design-in and test and measurement applications.DP-series diplexers are designed using low-pass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.TP-series triplexers are designed using low-pass, bandpass and high-pass filters and pass bias b...show more -
product
PXI 5W Programmable Resistor Module, 1-Channel, 3Ω to 22.3MΩ
40-252-054
The 40-252-054 is a programmable resistor module with 1 channel which can be set between 3Ω and 22.3MΩ with 2Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Pneumatic Zero Drop Tester
HIACC Engineering & Services Pvt. Ltd.
Designed as per ISTA packaging standard, the Pneumatic Zero Drop Test stand is used to assess the drop bearing capacity of the specimen during its transportation and handling process. The system is ideal for testing the specimen vulnerability around edges, surfaces and corners at different heights.
-
product
PXI 5W Programmable Resistor Module, 2-Channel, 1.5Ω to 472Ω
40-252-020
The 40-252-020 is a programmable resistor module with 2 channels which can be set between 1.5Ω and 472Ω with 0.125Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Automated Wafer Handler up to 450mm
GPR-GB7S
The GB7S Robot System employs Genmark’s breakthrough and patented GPR™ Technology to achieve the highest level of performance currently available in an automated wafer handler which is capable of handling up to 450mm diameter wafers. The patented GPR technology enables the servo-controlled robot to interface compliantly and intelligently with misaligned cassettes, FOUPS and process modules, as well as provide software-controlled end-effector deflection compensation during transport of heavier pa...show more -
product
Test for Pacemakers
VXI-based functional test system for testing implantable medical electronic products. The system is equipped with a Virginia Panel Series 90 adapter interface and can be operated standalone as well as on handling systems. Based on the previously developed matrix-based standard architecture, a large number of systems were supplied. The system function can be verified at any time via an automated self-test.
-
product
PXI 2.5W Programmable Resistor Module, 2-Channel, 1.5Ω to 472Ω
40-251-120
The 40-251-120 is a programmable resistor module with 2 channels which can be set between 1.5Ω and 472Ω with 0.125Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Large Substrate Mask Aligner
Model 6020
The Model 6020 is a large substrate Production Mask Aligner or Auto-flood Exposure System for RDL First Level Advanced Packaging (PLP) and markets requiring exposure of large glass panels. It is engineered with OAI’s precision, reliability, and quality that is found in all of OAI’s products. The features include wedge effect leveling, superb process repeatability, ≤ 2.0µm printing resolution, and remote diagnostics. Using robotic handling, the system can stand alone or be fully integrated with photo resist processing.
-
product
Inclined Impact Testers
Inclined impact testing simulates environmental dynamic forces that packaged goods may endure throughout transport and handling operations. These hazardous dynamics are simulated using impact test systems. Inclined impact test systems utilize a carriage that propels the test sample down a ramp at predetermined velocities before impacting into a fixed backstop. The specimen’s reaction to these extreme conditions indicates how the product would fare in real-world supply chain settings, allowing design engineers to make improvements to either the product and/or the protective packaging as needed.
-
product
Control Center
COSYMA
COSYMA is the control centre for APCOS®4000, consisting of a comprehensive and versatile application software that includes the following components:*Communications Network Control (CNC)*Radio & Device Control (RDC)*Secure Automatic Military Message Handling System (SAMMS)
-
product
Count Down Test System
The Second Launch Pad Count Down system is implemented using VXI hardware designed by Data Patterns specific to the application requirements, featuring a redundant system handling upto 14000 I/O points.
-
product
PXI 2.5W Programmable Resistor Module, 2-Channel, 1.5Ω to 6.97kΩ
40-251-124
The 40-251-124 is a programmable resistor module with 2 channels which can be set between 1.5Ω and 6.97kΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Portable Touchplate Wrist Strap Tester
Testing your ESD Wrist Strap system before handling electrostatic sensitive is extremely important. ESD events can go unnoticed by feel and sight. While a static discharge into a door knob (we’ve all done it!) can be thousands of volts, an ESD event can be as little as 10V, and you will not feel this. This is a no-frills, “go-no-go” type tester, but portable. Sure you could put this at your entry point, but where it really shines is in special remote applications. Keep one in your tool box, bag or Field Service Kit.
-
product
Chip Inspection System
GEN3000T
GEN3000T is an inspection system that performs automatic inspection of individual semiconductor chips.This revolutionary chip surface inspection system was achieved by combining the chip handling technology cultivated by Toray with the inspection algorithm used in the "INSPECTRA®" wafer defect inspection system.
-
product
AC Power Sources
i-iX Series II
AMETEK Programmable Power, Inc.
The iX Series II represents a new generation of AC and DC power source that addresses increasing demands on test equipment to perform more functions at a lower cost. By combining a flexible AC/DC power source with a high performance power analyzer, the iX Series II systems are capable of handling complex applications that have traditionally required multiple instruments.
-
product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 122Ω
40-251-012
The 40-251-012 is a programmable resistor module with 8 channels which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
PXI 5W Programmable Resistor Module, 1-Channel, 2Ω to 102kΩ
40-252-134
The 40-252-134 is a programmable resistor module with 1 channel which can be set between 2Ω and 102kΩ with 2Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Oil Test System
The Oil Test system Model OTS 2K1 is portable transformer oil Test system. It is a specially designed for accurate measurement of Loss Factor, Permitivity & Volume Resistivity Measurement of Transformer Oils & Petroleum jellys. The test frequency is 50 Hz . The system is provided with Mode Selector Switch so that once the oil cell is connected, it can measure all Three parameters in different modes without handling the test leads.
-
product
Handling Technology - Board Handling
ENGMATEC offers an extensive standard program of efficient and proven handling systems.
-
product
CANbus Module
DS-MPE-CAN2L
The module implements a CAN protocol bus controller that performs serial communications according to the CAN 2.0A and CAN 2.0B specifications. The protocol uses a multi-master bus configuration for the transfer of frames between nodes of the network and manages error handling with no burden on the host processor. Error analysis features enabling diagnostics, system maintenance, and system optimization. A listen-only mode enables CAN bus traffic analysis and automatic bit-rate detection.
-
product
Liquid Auto Refill System
LU Series
The LU Series offers uninterrupted, safe and reliable delivery of the liquid precursor to liquid material baking systems and injection systems. This leads to increased uptime, reduced operator handling and reduced risk of process contamination.The LU Series includes a function for automatically implementing a remaining liquid purge sequence.Using the LU Series, product throughput and maintenance efficiency is improved.
-
product
PXI 2.5W Programmable Resistor Module, 2-Channel, 2.5Ω to 1.51MΩ
40-251-044
The 40-251-044 is a programmable resistor module with 2 channels which can be set between 2.5Ω and 1.51MΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PCI-C664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous with ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
product
Single-Functional Testers
3122
The MI 3122 SMARTEC Z Line-Loop / RCD is designed specifically for live circuit testing. The instrument contains integrated characteristics of fuses and RCDs for the evaluation of test results. The online voltage monitoring system allows the operator to control what is happening on three simultaneous voltages in real-time. The bright red and green PASS / FAIL lights and help screens for each measurement make the handling of the instrument easy and clear. All the results can be quickly saved on the instrument and then downloaded via the optional A 1291 EuroLink PRO or A 1290 EuroLink PRO Plus software for evaluation and professional report generation after testing.
-
product
Robot Guidance Systems
Robot guidance using 3D vision systems designed for object localization is making a vital contribution to the optimization of industrial manufacturing processes. Robot guidance systems from SICK give users an easy, economical way to benefit from this sophisticated technology. The systems stand out thanks to their reliable, user-friendly design. They can be integrated without difficulty in existing environments, deliver high-precision measurement results and consequently play a key role in making part handling more versatile than ever before.
-
product
PXI 5W Programmable Resistor Module, 1-Channel, 1.5Ω to 1.81kΩ
40-252-122
The 40-252-122 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI 2.5W Programmable Resistor Module, 4-Channel, 2Ω to 13.6kΩ
40-251-031
The 40-251-031 is a programmable resistor module with 4 channels which can be set between 2Ω and 13.6kΩ with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.