-
product
SK Elektronik FID Analyzers
The Thermo-FID is an MCERTS approved extractive gas analyzer for the measurement of Total Organic Hydrocarbons (TOC) with a Flame Ionisation Detector (FID). Available in a number of different models, each version of the Thermo-FID employs the same detector unit, internal tubing and electronics. Distribution of sample and test gases is provided by using an innovative vacuum system which can be driven using plant compressed air or diaphragm pump.
-
product
Gas & Flame Detection System
Syntel
Teledyne Gas & Flame Detection
Syntel is an addressable loop system suitable for use in zone 1 and 2 hazardous areas. The complete addressable loo is fault tolerant operating normally with a short or open circuit. Syntel does not have a CPU, so there is no common failure point. It includes a standard OPC interface and can also be supplied by Modbus allowing easy integration with third party systems.Syntel stores alarm and calibration information in distributed non-volatile memory, hence there is no reliance on a centralized system.Syntel is ideal for installations where there is the possibility for future expansion. The system architecture allows very low cost expansion as cable runs to a central location are not needed.
-
product
Flame Ionization Detector
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the ...show more -
product
Heavy Impact Tester, Battery Safety Test
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's battery impact tester tests the safety of the battery through different weights, different heights and different impact areas. After a series of tests on this battery impact tester, the battery must not have flame or explosion.
-
product
Wireless Gas Detector
OLCT 80W
Teledyne Gas & Flame Detection
Teledyne Gas and Flame Detection is proud to introduce its wireless system with the OLCT 80 field detector/transmitter. This new model allows wireless connectivity in ATEX 1 zones. The maximum range is 3km, line of sight. The type of network selected will depend on the number of field detectors, the area coverage and the network architecture.
-
product
Stick Meters
Stick Meter and is packed with the portability, toughness and modular expandability HVACR professionals expect. This slim-shaped digital multimeter fits easily in your pocket or on your belt in the included case. Features most of the electrical parameters you use everyday including microamps DC for flame rectifier diode tests and capacitance for motor-run and motor-start capacitors. It’s a manual ranging meter and features a rugged ABS plastic housing with an O-ring to block contaminants, MAX hold, hi-voltage and continuity LEDs and beepers, and auto power-off (APO) to conserve battery life.
-
product
UV/IR Wet Bench Flame Detectors
SMC 3200/3300
The SMC 3200/3300 Series Flame Detectors utilize proven, stable UV/IR technology to continuously monitor for flames in wet bench and commercial applications. Due to its compact size, it is also used for installation in certain production equipment.
-
product
Gas Detection Controller
MX 52
Teledyne Gas & Flame Detection
The MX 52 control unit allows various detectors to be connected and monitored. Any gas detector from Teledyne Gas and Flame Detection or any other 4-20 mA device can be monitored and controlled.The modular design and flexibility enable this MX 52 gas detection equipment to be adapted to your exact requirements.
-
product
Flame Photometers
Flame Photometers are used widely in the measurement of alkali elements concentration in all sample types in: Mineral Extraction, Oil Industry, Paper Industry, Pharmaceuticals, Soil Analysis, Utilities, Food & Beverage, Chemical Manufacture and Fertilizer and Clinical laboratory testing and Pathological study in medical health.
-
product
Multi Channel Detectors
Dual, triple, quad and eight channel infrared detectors for gas analysis and flame detection sensors where more than one element or event is to be detected.
-
product
Tunable Detectors
Due to their spectral properties and robustness, pyroelectric detectors have proven themselves for many years in numerous applications in gas analysis, flame detection and spectroscopy. They enable the tuning of the optical filter over a defined spectral range by simply adjusting the control voltage. Instead of mounting filters to inspect specific areas of interest as is conventionally common, the detector with tunable Fabry-Pérot filters (FPF) can be used to monitor a broad spectral region continuously.
-
product
Communications Module
CC02A
The CC02A Communications Card facilitates serial communications between each module in a Zero Two Series Flame and Gas Detection System and an external host computer, which allows fast access to operational and setup data registers. It supports a Burst Read feature that returns all registers of a module in a single transmission.
-
product
Flame Testing
Helping you ensure acceptable flammability and flame resistance for electronic products and components.
-
product
SPI Flammability Tester (Vinyl Material)
TF318
TESTEX Testing Equipment Systems Ltd.
SPI Flammability Tester (Vinyl Material), to determine the ignition properties of vinyl plastic film material according to CFR 16 Part 1611 U.S.A. Flammable Fabrics Act for flammability of apparel vinyl plastic film.The rate of burning shall not exceed 1.2 in./s as judged by the average of five determinations lengthwise and five determinations transverse to the direction of processing, when specimen is placed at an angle of 45 degree and expose to the standardized flame (22# fire nozzle, 1/2 inch. In length).
-
product
Horizontal Flammability Tester
UI-TX40
Horizontal Flammability Tester – Horizontal Flammability Chamber is used to test textile and material used in vehicles horizontal burning rate when exposure to a small flame. Horizontal Flammability Test Method includes ISO 3795, ASTM D5132, JIS D1201, SAE J369, FZ/T01028, GB/T8410, GB/T20953 and etc.
-
product
Integral Explosive-proof Intelligent Flame Detector
FSE-100
FSE-100 Explosion-proof Flame Detector is used to collect the flame signal which is amplified and processed to determine the presence or absence of flame. FS-100 Flame Detector provides the flame output in real-time – the basis of determining the presence or absence of flame.
-
product
Masks Flame Retardant Performance Tester
WKS-1208
WKS-1208 Masks Flame Retardant Performance Tester is used to test the burning performance of the mask after contacting the flame at a certain linear velocity. It is special test instrument for the flame retardant performance of masks.
-
product
AFC 45° Automatic Flammability Tester
M233G
To determine the burning characteristics of textiles under controlled conditions. Stainless steel test cabinet with glass observation panel provided with automatic timing of flame spread in 0.1 second increments from ignition.
-
product
Single Channel Detectors
Infrared detectors for gas analysis, flame detection and radiometry in TO18 or TO39 packages.Housing types TO18 and TO39Voltage or current modeSignal processing with JFET or operational amplifierThermally compensated (optional)With special chip holder for reducing the microphonic sensitivity (optional)
-
product
Infrared Camera System
FlareSpection
The FlareSpection™ system provides extremely clear and reliable flare image and pilot flame monitoring of multiple flare tips. FlareSpection optimizes plant operations, improves safety, and ensures regulatory compliance. It enables you to remotely and automatically confirm flare operation and detect differences in flare stack heat signatures.
-
product
Test Lamp
TL105
The TL105 is a battery operated test lamp designed specifically to test General Monitors Flame Detectors. The TL105 is an explosion-proof test lamp that can be used with the FL4000H MSIR flame detector as well as any of the FL3100 Series Flame Detectors.
-
product
HCAI-1 High Current Arc Ignition Tester
HCAI-1
The HCAI-1 High Current Arc Ignition Tester is according to IEC 60950-1:2001, BS EN 60950-1:2001, BS 7002:2000, GB 4943.1-2011
and UL746A, IEC60947.1: 1999, GB/T14048.1-2000, IEC730.1:1993, GB14536.1-2008 and other standards required simulated safety test project. Parts and components of insulating materials or other solid combustible materials that are prone to flame spread in electrical and electronic equipment may ignite due to proximity or contact with electric arc, causing electrical fire and endangering the reliable operation of equipment and personal safety. -
-
product
Car Accessories Material Burning Tester
ZRS-4H
• Test Gas Source: Gas or Liquefied Petroleum Gas (Suggestion: Use good quality gas if possible) • Burner inner diameter: ￠9.5±0.5mm, about 100mm long with air adjusting hole • Height of flame: Can be adjusted from 20 mm to 100 mm according to the standard requirement • Applying time of flame: Burning time can be adjusted from 0 to 99 minutes 99 seconds • Test process: Automatic control • Inner volume: 0.05m³ • Material: Stainless steel or iron plate spray • Power: AC 220V; 50Hz/5A
-
product
Integral Intelligent Flame Detector
FS-100
FS-100 utilizes SMT technology which integrates a photoelectric sensor, a microprocessor, and a Human-Computer Interface (HCI) and an output interface together, sending out various outputs including an ON/OFF flame signal, a fault signal, a 4-20mA signal, and an RS-485 output (meets the MODBUS standard) via the quick connector.
-
product
Flat Pin-Staked Flex Jumpers
Series 171 thru 173
Flat Pin Staked Flex Jumpers. Aries Flat Pin Staked Flex Jumpers combine thin, flexible, solid Copper conductors embedded between layers of tough, flexible, flame- retardant insulation.
-
product
Spectrometer Systems
FLAME-CHEM
FLAME-CHEM spectrometers are fully integrated UV-Vis and Vis-NIR systems for measuring absorbance and transmission of liquid samples in cuvettes. FLAME-CHEM is a great option for teaching labs and research facilities where users seek the performance and flexibility advantages of the Flame spectrometer in a compact, small footprint instrument. Each FLAME-CHEM system comprises a preconfigured Flame spectrometer, a direct-attach light source and a cuvette holder for 1 cm pathlength cuvettes – all in a single package. UV-Vis (200-850 nm) and Vis-NIR (350-1000 nm) models are available. Add OceanView spectroscopy software (purchased separately) to complete your system.
-
product
Electrical Safety Tester
Basic testing methods of Glow wire device> and UL 746A, IEC829, DIN695, VDE0471, the Glow wire tester ZRS-3H/ZRS-3HS is suitable for resistance to abnormal heat and fire test on lighting lamps, electronic products and household appliances. Adopting high-temperature coating spraying on steel structure and imported instrument display, with easy operation, stable performance the equipment is applicable to flame resistance tests of all levels of QC departments and corresponding enterprises.
-
product
Flame & Other Plastics Testing
Educated Design & Development, Inc.
Plastics are tested to determine their flammability burning characteristics (Flame rating), their ignition potential due to thermal and electrical sources, their resistance to electrical tracking, and other electrical characteristics. The specific test required on a plastic depends on the type of component or end-use product, as well as the environment in which the plastic is used. This test equipment meets most UL, CSA, IEC, EN and other international safety standards.
-
product
Flash Point Tester
A flash point tester is an instrument that determines the flash point of a sample.To find the flash point, heat the liquid in a container and then introduce a small flame just above the liquid surface.the temperature recorded as the flashpoint.
