Showing results: 286 - 300 of 724 items found.
-
508 PV -
CRAIC Technologies
The 508 PV™ Microscope Spectrophotometer is designed to add spectroscopy, color imaging, thin film thickness measurement and colorimetry capabilities to your optical microscope or probe station. It can also be used to upgrade an older microspectrometer with cutting edge optics, electronics and software.
-
Canadian Microelectronics Corp.
This fixture clamps to microstrip or CPW lines at the edge of an RF board and is usable at any position without limit on size of circuit. The base is magnetic and it can be locked and released by a knob to accommodate any kinds of circuit configuration. Available for frequency ranges up to 40 GHz.
-
2410 -
Sensoray Co., Inc
Controls/monitors 48 digital signals over Ethernet PWM output mode Programmable input debounce Input edge detection with asynchronous host notification Compatible with standard solid state relay racks Embedded HTTP and Telnet servers Open source API
-
ADLINK Technology Inc.
Supports ADLINK PCI Express, PCI, PXI, USB DAQ devices and PXI controller, chassis, bus expansion modules, and edge platform.
-
SAMPULSE20x2 -
Furaxa, Inc.
The SAMPULSE20x2 is a demonstration board for the Furaxa SiGe3 30GHz sampler/pulser IC. The SIGe3 IC is a dual channel sampler pulser chip, and the SAMPULSE20x2 demonstration board contains two 2.4mm combined TDR input/output connectors, one to each sampler/pulser channel in the IC. The SiGe3 IC's two sampler outputs are then sent to to two SMA jacks, the first outputting the sample taken on the rising edge of the sampler clock, and the second containing the sample taken on the falling edge of the sampler clock. The sampler clock input, which must be a square wave, may be set to any frequency from 5MHz to 1GHz, causing the board take two pairs of samples (one on each clock edge) at rates from 5 million to 1 billion per second. A pulser clock input, which may be set to any frequency from 5MHz to 2GHz, and MUST be a square wave (preferably differential) with rise time under 100pS, causes the board to produce concurrent pulses on both of the SiGe3's I/O pins, which produce near-concurrent pulses at the two 2.4mm sampler/pulser TDR input/output connectors.
-
S12X and XGATE -
Cosmic Software
Cosmic Software's S12X and XGATE Development Tool Suite delivers the features and performance needed to create cutting edge applications. These tools are focused on leveraging the unique benefits of the S12X microcontroller family and XGATE module, while maintaining a standardized easy to use programming environment.
-
Blonder Tongue Laboratories, Inc.
Blonder Tongue Laboratories’ CMTS Edge Max supports both DOCSIS 3.1 and 3.0 with 32 downstream SCQAM and 12 upstream ATDMA channels for DOCSIS 3.0 service, and up to 6 OFDM downstream and 2 OFDMA upstream channels for DOCSIS 3.1 services.
-
CONAT -
F. W. Breithaupt & Sohn GmbH & Co.KG
*Rugged high-quality pressure-cast housing*Tracing edge with 110mm graduation*Mirror of chromed brass with sighting slot*Front to rear sight 110mm*Liquid damping of magnetic needle*Graduation 360° in 5° steps*Alternative: Conat with 6400-mil graduation and full mil specification
-
Unitech Scales And Measurements Pvt. Ltd
Bourdon Gauge Trainer comprises of bourdon pressure gauge fitted on a pressure chamber, a displacement sensor is attached to the edge of the bourdon tube to sense the deflection of the bourdon tube due to pressure. The displacement indicator is provided to measure the deflection of the tube in terms of pressure and also in mm.
-
P-1024P -
ELMA Electronic, Inc.
Special grade .125” sheet aluminum (5052-H32 EPS). Each side, edge and corner is carefully de-burred and chamfered to provide a flawless finish, resulting in a superior quality panel. , A multi-step painting process is used to paint the panel - the finish is textured unless otherwise specified.
-
P-1224P -
ELMA Electronic, Inc.
Special grade .125” sheet aluminum (5052-H32 EPS). Each side, edge and corner is carefully de-burred and chamfered to provide a flawless finish, resulting in a superior quality panel. , A multi-step painting process is used to paint the panel - the finish is textured unless otherwise specified
-
P-1224 -
ELMA Electronic, Inc.
Special grade .125” sheet aluminum (5052-H32 EPS). Each side, edge and corner is carefully de-burred and chamfered to provide a flawless finish, resulting in a superior quality panel. , A multi-step painting process is used to paint the panel - the finish is textured unless otherwise specified.
-
P-1424 -
ELMA Electronic, Inc.
Special grade .125” sheet aluminum (5052-H32 EPS). Each side, edge and corner is carefully de-burred and chamfered to provide a flawless finish, resulting in a superior quality panel. , A multi-step painting process is used to paint the panel - the finish is textured unless otherwise specified.
-
P-1724 -
ELMA Electronic, Inc.
Special grade .125” sheet aluminum (5052-H32 EPS). Each side, edge and corner is carefully de-burred and chamfered to provide a flawless finish, resulting in a superior quality panel. , A multi-step painting process is used to paint the panel - the finish is textured unless otherwise specified.
-
P-0124 -
ELMA Electronic, Inc.
Special grade .125” sheet aluminum (5052-H32 EPS). Each side, edge and corner is carefully de-burred and chamfered to provide a flawless finish, resulting in a superior quality panel. , A multi-step painting process is used to paint the panel - the finish is textured unless otherwise specified.