-
product
Variable Reluctance Absolute Pressure Sensor
AP10
The AP10, Absolute Pressure Sensor, is designed for low and medium pressure measurements, to laboratory accuracy, of corrosive liquids and gases. In typical AC excited bridge circuits, this transducer delivers a full-scale output of 40 mV per volt at 3kHz. The unit operates with carrier systems including the Validyne CD15 sine wave carrier demodulator and CD16 miniature DC input DC output carrier demodulator to produce a high level analog DC output suitable for recording and control.
-
product
USRP-2974, 10 MHz to 6 GHz, x86 Processor, GPS-Disciplined OCXO, USRP Software Defined Radio Stand-Alone Device
785606-01
The USRP-2974 is built on the LabVIEW reconfigurable I/O (RIO) architecture with an onboard Intel Core i7 processor running the NI Linux Real-Time OS. The USRP-2974 is a USRP Software Defined Radio Stand-Alone Device, meaning that you can target the onboard processor with LabVIEW Communications System Design Suite to deterministically perform processing. The USRP-2974 is also equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) Reference Clock. You can prototype a ran...show more -
product
ABex Rear Module with 8 Isolated Outputs and 5 Isolated Inputs
ABex RM-DIGIO
The ABex RM-DIGIO is a rear module for the ABex System. It is designed to connect digital signals to the back of a ABex chassis for example for cabinet control. As all IOs are isolated it’s possible to use different voltage levels for each IO.
-
product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 2.04k Ohm
40-294-022
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Vibration Testing
As specialists in dynamic testing, we provide equipment capable of exerting a 6,000 to 40,000 pound force with the capacity to perform closed-loop control from a single input to multiple channel inputs (from 2 to 32) with averaging or notched channel control. Vibration control systems can be programmed for real time monitoring, scheduled for length of time, or level scaled by dB or percentage, or scaled at various durations at different acceleration levels.
-
product
cDAQ-9171, 1‑Slot, USB CompactDAQ Chassis
781425-01
1‑Slot, USB CompactDAQ Chassis - The cDAQ‑9171 is a bus‑powered, CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. ...show more -
product
BitPhyer Tools
BitPhyer is a family of hardware platforms used to test the IEEE 802.3™ MAC, Flow Control, PCS and RS layers for Ethernet devices, including Automotive Ethernet. This platform is based on Xilinx FPGAs and custom built hardware which are used to create a flexible bit-level based test system.
-
product
Spring Testers
Imada offers manual or motorized spring testers in vertical or horizontal configurations.Lever-operated manual systems enable rapid compression and tension spring testing.Wheel-operated manual systems enable slower, more precise movement with the hand wheel.Motorized compression testers offer the most control and highest degree of repeatability with the ability to set a constant test speed and range of movement.All spring testers can be configured with a digital force gauge with data output for analysis by data acquisition software. An optional digital distance meter to measure displacement is available.
-
product
Soldering Station
SM-899D
*Using micro-processor PID program control technology, precise dual digital display hot air gun and the stability of the actual temperature of the soldering iron, fast automatic temperature compensation feature further enhanced temperatures.*The amount of wind, air flow, temperature soldering iron are adjustable.*The air gun holder is a magnetron (or light control), holding the handle when the system will automatically enter the working mode; handle is placed on the shelf when the system enters ...show more -
product
Static Inverters
Our static inverters are designed as uninterruptible power supplies (inverter in conjunction with rectifier and battery) to bridge short-term interruptions, power failures, voltage fluctuations, frequency fluctuations or generally to compensate for power disturbances in the data processing sector and in automation and control systems. They are used to supply AC consumers, primarily in the rail and industrial sectors.
-
product
cDAQ-9181, 1‑Slot, Ethernet CompactDAQ Chassis
781496-01
1‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9181 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
product
Fixed-Mount Thermal Camera
FLIR Axxx-Series Smart Sensor
The FLIR Axxx-Series Thermal Smart Sensor Camera has the features automation solution providers need for complex monitoring applications, including critical infrastructure, product quality, and early fire detection. The Smart Sensor configuration includes multiple measurement tools and alarms while also providing computing-on-the-edge, with analytics performed at the camera level for immediate results. With a range of lens choices, motorized focus control, and unrivaled connectivity, A400/A500/A700 cameras offer unmatched power and flexibility. Easy configuration allows you to tailor this monitoring system to your company’s quality, productivity, maintenance, and safety needs.
-
product
PXI Resistor Module 2-Channel 1.5R to 4.09k
40-293-023
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
3U OpenVPX Ethernet Switch and Multifunction I/O Board
68G5E
The 68G5E is a 3U OpenVPX board that is configured with an Ethernet Switch module (choose the ES1, 12-Port GbE Cu legacy unmanaged Ethernet Switch, or the ES2 16-Port Cu GbE managed Ethernet Switch with optional 4x 10GBASE-SR 850 nm multimode Fiber Optic interface) and provides additional support for one NAI smart I/O and Communications function module. Uniquely designed, the 68G5E provides ‘independent’ Ethernet Switch capabilities and can operate as a MFIO board end point with access via the 1...show more -
product
Isolated A/D Converters
As the world’s leading supplier of data converters, Analog Devices is constantly introducing new A/D converters (ADCs) that drive system architectures. In the motor control arena, ADI’s converters solve the challenges associated with current and voltage monitoring, optical encoder feedback, and resolver-to-digital conversion. The introduction of the isolated ADC with its 3.75 kV standoff voltage is one example of ADI’s breakthroughs in performance and integration to ease the burden of design.
-
product
Data Analytics
KLA’s data analytics systems centralize and analyze the data produced by inspection, metrology and process systems. Using advanced data analysis, modeling and visualization capabilities, our comprehensive suite of data analytics products support applications such as run-time process control, defect excursion identification, wafer and reticle dispositioning, scanner and process corrections, and defect classification. By providing chip and wafer manufacturers with relevant root cause information, our data management and analysis systems accelerate yield learning rates and reduce production risk.
-
product
Digital Module For Remote I/O
Digital Modules for Remote I/O provide 24 V digital inputs or outputs and offer 1‐, 2‐, 3‐, and 4‐wire spring terminal connection options. You can use inputs as counters or standard digital inputs, and you can adjust filter time to improve measurement quality. Inputs can include a built‐in power supply for sensors. Output modules feature circuit and overload protection and can drive up to 500 mA per channel, up to 8 A per module.A remote I/O system consists of an EtherCAT bus coup...show more -
product
Transportation Embedded System
Certified by the strict railway/vehicle/marine safety and EMC criteria, the transportation embedded systems (tBOX) are designed for transportation industry applications. The tBOX embedded systems feature wide operating temperature ranges, powerful computing performance, and high vibration resistance. The tBOX box PCs can work in various applications including fleet management, passenger infotainment systems, onboard and wayside surveillance systems, onboard device controls, gateway and dispatching systems, and more.
-
product
IO-Link
The IO-Link® interface simplifies communication to smart sensors and actuators, combining signaling with power-over-cable technology. It has become one of the key devices as industrial automation systems are growing more interconnected and intelligent to accommodate demands for centralized control and optimized production. Analog Devices implements both device PHY and master PHY interfaces (COM1/COM2/COM3). Designing with harsh industrial environments in mind, the master 4-port IO-Link power and...show more -
product
24-Bit Precision Load Cell Input Card
PCI-9524
The PCI-9524 is a robust, multi-purpose module designed for turnkey material test systems (MTS). Equipped with four strain gauge-based transducer input channels, four general purpose analog input channels, and a 3-axis motion controller, the PCI-9524 delivers a complete hardware solution for MTS manufacturers. The PCI-9524 easily integrates physical quantity measurement and implements strategy of close-loop control in a single module package. For transducer measurement, the PCI-9524 supports sensitivity from 1.0 mV/V to 4.0 mV/V and provides a 1/200000 accuracy of measurement of full scale. These features make the PCI-9524 suitable for precise measurement in large-scale transducers.
-
product
Tan Delta Test System
Precision measuring bridge is designed for determining the capacitance and dielectric dissipation factor of liquid and solid insulants, cables, capacitors, line transformers, generators, motors, bushings etc. Furthermore it can also be used for power loss measurement on shunt reactors or similar apparatus. This system is suitable for both low and high voltage measurement at line frequency. Measurement reports can be printed. This measuring equipment has been specially developed to maximise efficiency in production and quality control environments. Its outstanding accuracy also makes it suitable for laboratory and research applications.
-
product
Stationary Drive Test System
ACTAS CF80
Stationary test system for sequential final factory tests and function tests on up to 8 drives. The drive test system is operated and controlled with the ACTAS operating software. The test position is selected using the multiplex method. The test system can reproduce drive control with the aid of a logic module. This makes it possible to test any drive even if there is no control unit.
-
product
AM Control System
Clamir
*Continuous monitoring of melt pool dynamics and geometry.*Ensures quality and repeatability.*Compatible with most laser heads.*Compatible with a wide range of materials.*Easy mechanical integration.*Quick configuration.*Helps to reduce CO2 emissions.
-
product
Voice System for Air Traffic Control
VCS
CERTIUM® VCS is a quad-redundant, IP based voice communications system that integrates perfectly into the entire CERTIUM® portfolio for safe, secure and efficient airspace operations. It combines a state-of-the-art, flexible and resilient IP based architecture with strong security mechanisms. It is flexible enough for both small towers and nationwide systems with multiple area control centers and hundreds of controller working positions. CERTIUM® VCS has advanced functions that can support remote digital tower systems or connect area control centers to virtual centers for quick and flexible transfers between centers and even countries.
-
product
PCI High Density Resistor Card 3-Channel, 24-Bit, 0 To 16M Ohm
50-295A-021-3/24
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Advanced Metrology System
AMS Series
Precision systems for accurate measurement and quality control in semiconductor manufacturing.
-
product
Chamber/Pyroelectric Task
Radiant's Chamber/Pyroelectric Task sets the sample to a series of temperatures by performingGPIB control of an external thermal device. At each temperature it captures the sample’s polarization response and/or small-signalcapacitance. These are combined to calculate the pyroelectric coefficient. The Pyroelectric Task is to be used with a Radiant Test System and a Linkam Stage (-196C to 600C), Thermal Chambers, Hot Chucks, or a Furnace to automatically measure the Pulse Polarization respo...show more -
product
Portable Small Meter Tester
The Portable Small Meter Tester (PSMT) is a lightweight system for field testing of 5/81 in. meters. It includes a test meter with control valves, hose connections, fittings and pressure gauge. Meter tests can be done without removing them from service. The inlet control valve ensures an accurate test start and stop. A globe valve downstream from the meter allows flow rate adjustment during test. Connection to the PSMT is made using standard 3/4 in. male hose connections located on the exterior of the case. Two 3/4 x 39 in. metal-reinforced flexible hoses are provided for easy field connections.
-
product
ATOS ScanBox
Series 7
The ATOS ScanBox Series 7 is mainly used in car manufacturing, in try-out toolmaking and in press shops. The optical 3D measuring system performs complete analysis measurements for comparison in the introductory phase or is used for quality control in production. Large parts such as automobile side panels and attached parts of up to 6 m in size can be measured. The full- field measuring data enable the analysis of hole pattern, trimming and character lines. Even heavy and large parts for other applications can be measured and inspected with the ATOS ScanBox Series 7.
-
product
Modular Power
RFP DC High Power
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
