Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
product
LXI Microwave Multiplexer, SP4T, 14-Bank, 50GHz, 50Ω, SMA-2.4, Terminated
60-803-714
Our 60-803-714 is a 14 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Single 2x2 Insert/Bypass 850nm M-Mode
40-820-112-M
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
product
14-bit 16 Concurrent Channel 65MSPS A/D board
AD14-65Mx16AVE
14-bit 16-concurrent channel 65MSPS A/D board for demanding large-system uses, where signals on multiple time-aligned channels need to be observed with high SNR, such as RADAR, nuclear instrumentation, ultrasound, medical imaging, spectroscopy, communications systems, RF component and antenna testing and other critical applications. An on-board low-jitter LMX2581-based RF synthesizer allows any A/D sampling rate between 20MSPS and 65MSPS to be specified in software. A second on-board LMX2581 ...show more -
product
VPC Receiver Frame
ABex REC21-84TE-EXT
Robust and flexible interconnect solution for test fixtures. Designed for the use with ABex PXIe Rack 18 it provides support to equip all 21 slots with VPC interconnect modules. In addition, it offers 6 more slots on the bottom, below the ABex rack to feed through signals from external measurement devices.The interface uses the well-known Virginia Panel connectors with more than 20.000 guaranteed mating cycles. To build DUT specific test fixture, we also provide the corresponding ITA mounting frame (ITA = Interchangable Test Adapter).
-
product
Balanced and UFL Calibration Kit
CAL-UFL-BAL
The Balanced Calibration Kit is an interface kit for UFL and balanced VNA measurements. It contains SMA-UFL adapters and several adapters from SMA and UFL to balanced pinheaders. The UFL connector was introduced by Hirose as the U.FL connector and became very popular for connecting RF signals in consumer electronics. There are several varieties from other manufacturors and are also known as UMC or UMCC connectors.
-
product
LXI Microwave Multiplexer, SP6T, 8-Bank, 26.5GHz, 50Ω, SMA
60-800-308
Our 60-800-308 is a 8 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
LXI Microwave Multiplexer, SP6T, 3-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-800-503
Our 60-800-503 is a 3 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Cable Assembly, 160-Pin DIN41612, Female to Female, 2m, 45º
A1604F5-1604F5-0A200
For applications where a 45 degree cable exit would be preferred. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connectors to have a second fixing then the connector can be fitted with the optional screwlock assembly 40-969-101 where applications permit.
-
product
SC Connectors
Pasternack SC connector category RF coaxial has many part numbers, the majority are RoHS and REACH compliant. Coaxial SC connectors in this category will terminate to coax or terminal. Our RF SC connectors are built to precise RF and microwave industry specifications. Connectors in RF coaxial SC are constructed in male or female gender with 50 Ohm impedance. SC connector products are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These rad...show more -
product
LXI Microwave Multiplexer, 50Ω 6-Channel 11-Bank 26.5GHz SMA
60-801-311
The 60-801-311 is a 6-channel, 11-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
RC68-68, Ribbon Cable, 68 D-Type to 68 VHDCI Offset, .5 Meter
187252-0R5
68-Pin Female to 68-Pin Female, 1 Ribbon Connection Ribbon Cable - The R68F-68F Cable, sometimes referred to as the R68-68 or RC68-68, is a flat ribbon cable that connects to 68-pin NI data acquisition or digital I/O devices. The R68F-68F Cable is offered in different lengths and with D-SUB or VHDCI front end connectors.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode
40-850A-214
The 40/42-850A-214 is a PXI/PXIe 4-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 40GHz, 50Ω, SMA-2.9, Internal Termination
40-781A-422
The 40-781A-422 (PXI) and 42-781A-422 (PXIe) are dual SPDT 40GHz microwave relay modules with internal terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50GHz in 50Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
Power Supplies
CU-series
The CU-series is a semi-modular power supply that lets you select the cables you need while powering your system at a healthy voltage. Everyone likes a clean and easy installation. This power supply allows you to keep what you want and remove what you don't. While necessary connectors, like the 20+4 pin power connector, are attached to the unit, you decide which of the others should stay. Customize your power supply to reflect your system.
-
product
6U High-Density PXI RF Matrices
Pickering's 6U high-density matrices are suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high-performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture - this maximizes isolation and RF performance.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, FC/PC Connectors, With Interlock
42-850A-114-HI
The 40/42-850A-114-HI is a PXI/PXIe 4-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Visible Fault Identifier
TVFI
The Yamasaki TVFI Visible Fault Identifier is a practical palm sized solution for finding breaks, bends and faulty connectors or splices in fiber optic cable.
-
product
LXI Microwave Multiplexer, SP6T, 2-Bank, 67GHz, 50Ω, SMA-1.85
60-800-802
Our 60-800-802 is a 2 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
50 Pin SGMC Connectors for Pickering
The connectors below are suitable to use with Pickering cards and modules that utilize the 50-pin SGMC connector.
-
product
PXI/PXIe RF Matrix, 16x4, 150 MHz, 50 Ω, SMB, With Y Loop-thru
42-724-012-L
The 40-724-012-L (PXI) and 42-724-012-L (PXIe) are 16x4 RF matrix modules with y-axis loop-thru and are suitable for switching frequencies up to 150 MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
-
product
LXI Microwave Multiplexer, SP4T, 13-Bank, 26.5GHz, 50Ω, SMA
60-803-313
Our 60-803-313 is a 13 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode
40-850A-014-M50-HI
The 40/42-850A-014-M50-HI is a PXI/PXIe 4-channel multiplexer with FC/APC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
PXIe Microwave Relay, Single SPDT, 26.5 GHz, 50 Ω, SMA, Internal Termination, Failsafe
42-781A-221
The 40-781A-221 (PXI) and 42-781A-221 (PXIe) are single failsafe SPDT 26.5 GHz microwave relay modules with internal terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
Tumbling Barrel Tester
CX-G13
Shenzhen Chuangxin Instruments Co., Ltd.
Tumbling Barrel Tester The Tumbling Barrel Test simulates repeated falls which may occur to such devices as connectors or small remote control units which are normally attached to cables during use.
-
product
Seismic Signal Conditioners
Seismic signal conditioners are designed to accept an input from (and provide power to) a seismic sensor. They convert the signal to a proportional 4-20mA DC signal that can be used as an input to process control instrumentation such as a PLC or DCS. They provide additional convenience features such as optional displays, BNC connectors for access to the dynamic sensor signal, and bandpass filtering. Metrix offers seismic signal conditioners that can accept either acceleration or velocity sensors, and are available with or without an integral display.
-
product
Backplane Connectors
Offering a broad portfolio of backplane connectors that include SOSA aligned optical, COTS plus hard metric, VITA standard and high speed twinax interconnects. Our interconnect solutions address the requirements of mission-critical applications within commercial aerospace, space and defense market segments.
-
product
Precision Fiber Optic Cleaver With Scrap Collector
HW-05C
Shanghai Fibretool Technology Co.,Ltd.
The HW-05C Fiber Optic Cleaver gives you high precision at low cost. This compact and easy to use cleaver is perfect for all cleaving applications, from fusion splicing to mechanical splicing and field installing quick termination connectors. The HW-05C works with both 250um coated and 900um buffered fibers.
-
product
Cable Tester, Coax Cable Mapper 8 ID Finder with Toner
TCT-128
A handheld testing device designed for CATV and security installers to test multi-run coaxial cable systems terminated with "F" or BNC connectors. Uses eight color coded ID finders to locate and identify cables.
-
product
TB-2648, Screw Terminal, 4x128, 1-Wire PXI Module Matrix Terminal Block
781131-01
Screw Terminal, 4x128, 1-Wire PXI Module Matrix Terminal Block - The TB-2648 provides the necessary routing to configure the PXI-2531 or PXIe-2531 PXI Matrix Switch Module as a 1-wire 4x128 matrix. You can directly connect the TB-2648 to the front panel I/O connectors of the PXI-2531 or PXIe-2531.
-
product
LXI Microwave Multiplexer, SP4T, 12-Bank, 26.5GHz, 50Ω, SMA
60-803-312
Our 60-803-312 is a 12 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
