Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
product
Terminated Latching/Failsafe, SPDT, 50Ω Impedance, 2.4mm (U) Connectors, Internal 50Ω Terminations on Unused Ports, DC-52GHz
Part No. CCRT-50U
Terminated Latching/Failsafe, SPDT, 50Ω impedance, with 2.4mm (U) connectors. Includes internal 50Ω terminations on unused ports.DC-52GHz
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 12-Bank 40GHz SMA-2.9
60-801-412
The 60-801-412 is a 6-channel, 12-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
Complex Industrial Connectors
C.C.P. Contact Probes Co., LTD.
Special Environments need special connectors. CCP offers connector designs that are suitable even for military and outer space applications. Their extreme reliability, long life cycles and robust designs are revered by our customers.
-
product
Rackmount Kit For Infiniium EXR-Series, 8U
EXR2RACK
The EXR2RACK rack mount kit includes all parts needed to mount your Infiniium EXR-Series oscilloscope in an 8U open frame rack and includes a Support tray, Trim plates, BNC connectors to be inserted into the bottom trim plate, black rubber stoppers to plug holes in bottom trim plate if the hole is not being used for a BNC connection, Two track rails, Two clamp brackets, both right and left Top clamp brackets, screws, and nuts.
-
product
FMC, XMC & PMC
The FPGA Mezzanine Card is used by Data Patterns to implement signal interface with external world compatible FPGAs mounted on the FMC carrier there are primarily used for high speed analog interface for digitization (ADCs) and waveform generation (DACs). This form factor is also utilized for special I/O Interfaces such as various avionic protocols and buses. FMC I/O signals may be routed via front panel connectors or through Mezzanine connectors that route the signal back to the carrier board for routing through rear I/O of the Chassis. The system interface is designed for routing to FPGAs using a VITA 57 0.05 Pitch Terminal Array Assembly.
-
product
Accessory Kit, Type-N, 50-Ohm
11853A
The Keysight 11853A accessory kit furnishes the RF components required for measurement of devices with 50-ohm, type-N connectors and when using a network analyzer with a type-N configuration. Each kit contains a type-N (female) short, a type-N (male) short, two type-N (male) barrels, two type-N (female) barrels, and a storage case.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, MU Connectors
42-850A-314
The 40/42-850A-314 is a PXI/PXIe 4-channel multiplexer with MU (mini SC) connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
78-Pin D-Type Block Without Backshell
92-965-078-F
This connector block provides a simple method of connecting to 78-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties.
-
product
37-Pin D-Type Connector Block
92-965-037-M
This connector block provides a simple method of connecting to 37-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties.
-
product
Standard Mechanical Calibration Kit, DC To 7.5 GHz, 7–16 (male)
85038M
Modern wireless communication systems require high-performance components offering low VSWR and low intermodulation distortion at high transmit power levels. To meet these needs, 7-16 connectors are becoming increasingly common in base station transmitters, amplifiers, duplexers, and other products. These connectors conform to IEC 169-4, DIN 47223, European standard EN 122190, and British standard BSEN 122190.
-
product
8 Ch Dual Range Multievent Peak Sensing ADC
V1785
The VME interface is VME64 and VME64X standard compliant and features the A24/A32 and MultiCast addressing modes. The data readout occurs either in D32, BLT32, MBLT64 mode, or in daisy chain with 32/64 bit Chained Block Transfers. The module features a fully programmable RORA interrupter.The board is provided with the P1 and P2 VME connectors and fits into both V430 and standard 6U crates.
-
product
Character Generators
Overlays Text on VideoFront Panel Programmable or via RS232 Computer LinkUp to 32 MCG-2 on one RS232 busGenlocks to either NTSC and PAL automaticallyCharacter/Background Brightness AdjustableFour Character Heights and Four Character WidthsA-Z, 0-9 and Punctuation Marks Character SetBuilt in Menus, Help Screens and Self-testReal Time Clock (RTC) optionRemote Control via RS232 (RJ11 Connector)BNC Video Connectors, 4 Pin MiniDIN on S-VideoTen Pages of Text Storage in MemoryLithium Battery Backup (10 Year Life)Can be powered from external 12Vdc, for Field useCompact Size in a Rugged Aluminum and Steel EnclosureTwo Year Warranty, Made in USA
-
product
PXI/PXIe Microwave Relay, Quad SPDT, 40GHz, 50Ω, SMA-2.9
40-780B-544
The 40-780B-544 (PXI) and 42-780B-544 (PXIe) are quad SPDT 40GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
product
Rolling Seal 8 Optical Connector - APC (RS8 APC)
The Angled Physical Contact Rolling Seal 8 Connector (RS8 APC) from Teledyne ODI is a wet-mateable optical connector with angled endfaces. The design reduces signal interference due to reflections at the connector face, supporting the next generation of subsea optical communication equipment. The Rolling Seal design provides isolation from seawater and silt when the connectors are unmated. As the seals rotate, the fibers join inside a clean, oil-filled conduit, resulting in a reliable optical throughput. The RS8 APC incorporates RS8 Mark III design features to enhance operational efficiency and reduce risks during ROV intervention.
-
product
LXI Microwave Multiplexer, SP6T, 14-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-800-514
Our 60-800-514 is a 14 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI/PXIe Power Relay Module, 24xSPDT, 5 Amp, 50-Pin SGMC Connectors, With Interlock
42-158-002-HI
The 40/42-158-002-HI is a PXI/PXIe high density power relay module with 24xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
product
54 Piece Automotive Test Connector Kit
146
This comprehensive test kit features a variety of terminal adapter sets which enable connection to most automotive vehicle connectors, both foreign and domestic. Terminal adapters connect via the included 48 inch stacking banana plug test leads. Connection to most DMM’s and scopes is no problem. Kit is designed to provide wide testing coverage and quicken the test process.
-
product
Cable Assembly, Receiver, TriPaddle, 20", 2 20-Pin Power Connectors
540054040101
Cable Assembly, Receiver, TriPaddle, 20", 2 20-Pin Power Connectors.
-
product
2.92mm to ProBus Probe Adapter
L2.92A-PBUS
The Teledyne LeCroy LabMaster 10 Zi oscilloscope utilizes precision 2.92mm input connectors to achieve up to 36GHz of input bandwidth. But some applications may require the use of lower-bandwidth probes for performance and cost reasons.The L2.92A-PBUS adapter converts the 2.92mm interface to a ProBus interface. This brings the benefits of a wider selection of probes to the LabMaster 10 Zi from high-impedance ZS active probes to the high-bandwidth WaveLink differential probing system. Full probe power and control is provided through a built-in LEMO interface.
-
product
Production Connectors
Production Connectors for the manufacturing and testing of component assemblies. Handheld Production Connectors for assembly lines. Machine Mounted Test Connectors. Part-in-Place detection.
-
product
In-Line Signal Conditioner
500
Small, DC powered in-line signal conditioner with 9-pin connectors, +/-5V and 4-20mA outputs and 1000Hz bandwidth.
-
product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Single-Mode
40-855A-122
The 40/42-855A-122 is a PXI/PXIe dual 2-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
PCB Adapter, Receiver, TriPaddle, 64 Position, To PCB-Mounted 2x34 Pin (BERG 65496-019) Connectors
510104128
The 64 Pin Signal Receiver Module is made from Ryton® R-7 and will withstand temperatures up to 220°C. The 64 Pin Signal ITA Module is made from engineered resin and will withstand temperatures up to 150°C. Both the ITA and Receiver Modules have molded nomenclature.
-
product
68-Pin SCSI Micro-D M to 2x34 2m
40-971-068-2m-MF
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 2x34-Pin Twisted Pair cable with PVC insulation, terminating with 2x34-Pin polarised IDC connectors. Strain relief is provided via a metal spring latch on the 68-Pin connector.
-
product
UHF/RFID Power Divider Combiner 4-Way, BNC Female, 350-1000 MHz, 30 Watts
PD2541
INSTOCK Wireless Components, Inc
PD2541 is a RoHS compliant, 4 way, wideband, 50 ohm, RF power divider, power combiner furnished with BNC jack female coaxial connectors. All wireless band frequencies in the range from 350 to 1000 MHz are covered with optimal RF performance. Max microwave input power levels up to 40 watts can be handled in both power splitter and power combiner applications. See 4 way power divider input rating tables for additional details.
-
product
Premium Interfaces
Ramsey Electronics Premium Interfaces - USB, ethernet, video, and RF filtered power interfaces/rf data connectors
-
product
RTM Communication Board
MS 3636I
CPCI Rear IO Communication Board is a signal conditioning and interface board for CPCI Integrated Communication Card (MS3635i). This board has required signal conditioning and interface circuits for RS422. Two 96 Pin Euro Connectors are used to interface all IO’s.
-
product
Broadband Power Amplifier
PAS-00023-25
* Solid State Power Amplifier* Gain : 46 dB typ.* High IP3, 48.0 dBm typ.* Bench Top Case* Internal Cooling Fans* Over Temperature Protection* Type N Connectors
-
product
PXI/PXIe RF Matrix, 8x4, 300 MHz, 50 Ω SMB With Loop-thru
40-729A-001-L
The 40-729A-001-L (PXI) and 42-729A-001-L (PXIe) are 8x4 50 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 6-Bank 18GHz SMA
60-802-206
The 60-802-206 is a 4-channel, 6-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
