Showing results: 406 - 420 of 2823 items found.
-
JT 2111/MPV DIOS IDC -
JTAG Technologies Inc.
The JT 2111/MPV is a 64 channel boundary-scan digital I/O scan module enclosed in an impact resistant housing. The module is designed to test and control edge connectors, on-board connectors and logic clusters in boundary-scan applications. Multiple modules can be connected serially to increase the number of I/Os. Available with 96-pin DIN 41612 connectors and 20-pin 0.1″ pitch IDC connectors.
-
AS1/2 -
VECTOR Electronics and Technology, Inc.
Fits onto rear face of rear extrusion rails to mountDIN 41612 type connectors directly in subrack.HP pitch pattern of holes for precise installation of connectors.
-
540273010055 -
Virginia Panel Corporation
2 PCB Adapters, Receiver, QuadraPaddle, two 192 Position, to 2 PCB-Mounted Female VHDCI Connectors (510150126) and 2 PCB-Mounted InfiniBand Connectors (510150210)
-
MCT 192 -
REINHARDT System- und Messelectronic GmbH
MCT 192 is an easy-to-use high-speed cable tester for testing multi-wire cables and complete backplanes. The multi-contact board is equipped with contacting sockets and connectors common in industries. Fixturing is therefore unnecessary. In case you use connectors which are not supplied with the multi-contact board, you can mount and wire these connectors on a raster plug-in board.
-
DORC's ZX-1 -
Direct Optical Research Company
Used primarily to measure multi fiber (MT/MPO and MT-RJ) connectors, DORC's fourth generation "ZX-1 mini Array+" is the result of 18 years of hardware and software product development. Although optimized for mutifiber connectors, the ZX-1 mini Array plus also does an excellent job of measuring single fiber PC and APC connectors. DORC's patented design is based on a variant of the Michelson configuration, and provides BOTH 2D and 3D high resolution images of the sample under test in approximately 45 seconds for multi fiber connectors and just 3-4 seconds for single fiber connectors - from the time the connector is inserted.
-
N4432D -
Keysight Technologies
The Keysight N4432D is a precision 4-port ECal module that supports selection of Type-N and 3.5 mm connectors mixed up to 18 GHz. Select either female-female, male-male, or female-male connectors.
-
SparkFun Electronics
RJ45 connectors are the kind that are used for Ethernet jacks, but they make great general purpose connectors when you need a lot of conductors. This is a small PCB that brings out the pins of the RJ45 connector to an in-line 0.1" footprint. Use with break-away headers for breadboarding or create your own RJ45 cable. Check the related items for Ethernet cable and connectors to go with it!
-
N4431D -
Keysight Technologies
The Keysight N4431D RF electronic calibration (ECal) module makes calibration of Keysight vector network analyzers fast, easy and accurate. The N4431D is a precision 4-ports ECal module that supports multiple selection of connectors like Type-N, 3.5 mm, 7-16 and 4.3-10 connectors and can be mixed up to 13.5 GHz. Select either female-female, male-male, or female-male connectors.
-
40-969-101 -
Pickering Interfaces Ltd.
This screwlock assembly can be used in LXI applications where 4 connectors are used in a horizontal row if the user requires the connectors to have a second fixing. It is also suitable for use with other products and in other situations.
-
60-711-711 -
Pickering Interfaces Ltd.
The 60-711 is a Dual 24x8 Video Matrix Module suitable for switching frequencies up to 25MHz. It has a characteristic impedance of 75Ω with the option of SMB or MCX connectors or, with a larger case size, BNC connectors.
-
YOKOWO Co., Ltd.
Connectors that connect to the RF Line at the end of the board.
-
-
Circuit Check, Inc.
Circuit Check supports reading linear bar codes and 2D symbols within each of its fixture product lines.When spring-loaded probes are not practical or access is limited, Circuit Check can help you with thru-connector tests to contact connectors on any surface or edge of a circuit board. These tests can be implemented spring probes, mating connectors, sacrificial SMT connectors, and stabber cards.
-
MTI Corp.
8 cables with optional connectors are included in the standard package for immediate useTThe connectors to the board are the banana plug for easy insertion and removal,(AS Shown in pic-1). The Banana Plug of the cable are 4mm banana plug, Max wire diam.4.2 mmAnother end or of connector testing system are optional connectors (choose the right one for you from above "connector type" when order)
-
Langer EMV-Technik GmbH
The MP CI set up to measure coupling impedance is used to determine EMC characteristics of connectors and cables. The coupling inductivity defines the coupling inductance of external disturbance on the shield or on the ground with the desired signals. If the coupling inductivity is considered in the construction set-up and the pin or wire assignment of connectors or cables, then the connectors or cables will be more interference-resistant. The MP CI set-up for measuring coupling impedance can be used for following measurements at connectors or cables: 1. measurement of a single signal (common mode) 2. measurement of a symmetrical signal (common mode) 3. measurement of a symmetrical signal (differential mode)