-
product
HV Circuit Breaker Analyzer
CBA-32P
The CBA-32P is a multifunctional circuit breaker analyzer performing Motion, Timing and Dynamic Resistance Measurements, all in a single test.
-
product
Short Circuit Loop Impedance Meter
AMZC-305
Loop impedance measurement with resolution 0,01Ω ; Loop impedance measurement without tripping the circuit breaker > 30mA with resolution 0,01Ω (100...440V) ; Measurements possible in installations 110/190V, 115/200V, 127/220V, 220/380V, 230/400V, 240/415V, 290/500V and 400/690V (range 100...750V)
-
product
Non-Contact Voltage Tester
NCVT-1
Non-contact detection of voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets, and wires.High intensity, bright green LED indicates the tester is operational and aids in illuminating the workspace.When voltage is detected, a high intensity, bright red LED illuminates and a warning tone sounds.Discrete digitally controlled ON/OFF power button.Auto power-off feature conserves and extends battery life.Microprocessor controlled low-battery indicator and tester shutdown.CAT IV 1000 Volt safety rating provides expanded operation and protection.
-
product
AC Electronic Load
The electronic AC loads cover a wide variety of different voltage, current and power ranges. All the AC loads are programmed with 11 different sine, square and DC waves. With 5 crest factor variations of each, a total of 55 waveforms are available. An external input is also provided to enable the user to amplify signals from a waveform generator.AC Loads allow real world operating conditions to be simulated. Typical applications include circuit breaker, transformer & UPS output testing along with general laboratory and research work.
-
product
Electrical Circuit Protection - Breakers
Eaton’s complete line up of low and medium voltage circuit breakers and fuses are used to provide circuit protection in alternative energy, commercial, industrial, mining, and military applications, where they protect against overloads and short circuits in conductors. These circuit breakers are applied in panelboards, switchboards, motor control centers, control panels, combination starters, individual enclosures, and bus duct plug-in units.
-
product
300kV/5mA DC Hipot Tester
HDZG
HD Power Test Equipment Co.ltd
HDZG-305 300kV/5mA DC high voltage tester is used for testing DC high voltage for zinc oxide arresters,magnetic blowing arresters, power cables,generators,transformers,circuit breakers and other equipments,which is suitable for electric power branch,power department of factories,scientific research units,railway,chemical industry,and power plants.
-
product
Intelligent Circuit Protection
The Mors Smitt ‘Intelligent circuit protection system’ controls and monitors all AC and DC circuit breakers remotely and is capable of providing complete status of all MCB’s via display or through the Train Management System.
-
product
RCD Testers
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2710 is a residual current tester, which is used to determine tripping currents and the tripping times of residual current circuit breakers, which are used in every new building according to current building regulations. Residual current circuit breakers are used for personal protection and switch off a circuit when a residual current is registered which flows off via the protective earth (PE). RCD testers let a fault current flow and thus determine at which fault current the RCD tr...show more -
product
6 Contacts- Circuit Breaker Analyzer
CB14
The CB14 is a 6 contacts circuit breaker analyzer designed to perform Timing, Motion as well as Static & Dynamic Resistance Measurement (DRM) in a single test. It also includes 3 multifunction analog inputs.
-
product
HV AC Test Set
SERIES S400 TYPE RX I O/ I OACP
K&S Engineering and Scientific Ltd
The output is continuously variable from zero to 10 kV by means of the panel mounted regulator. An output trip is fitted which operates when the output exceeds 25 mA switches off the test set and operates a neon overload indicator. Primary protection is provided by two panel mounted fuses. The output is protected by the output trip and a magnetic/hydraulic circuit breaker.
-
product
Transformer Rectifier Assemblies
Transformer rectifier assemblies are very useful in OEM applications when unregulated DC output is required. Input power can be single-phase or three phases. With single-phase input power, the output ripple is 50%. With three-phase input power, the output ripple is 5%. A 5% output ripple is a clear advantage. Hence, transformer rectifier assemblies with three-phase input power are more popular. Circuit breakers, fuses, voltmeters, and ammeters can be added per customer requirements. The assemblies can be an open frame or inside an indoor enclosure.
-
product
Programmable DC Power Supply
CBCT
The CBCT is a variable voltage DC power supply designed specifically to test substation circuit-breaker Open and Close coils. The CBCT uses the substation’s DC power supply to electronically generate a programmable output voltage from 5% to 95% of the source voltage. The CBCT can maintain up to an 80A test current while maintaining 2% or better voltage regulation during the circuit breaker coil operation.
-
product
Panel Meter Calibrator
1040C/CU
Calibrate panel meters, transducers, circuit breakers and relay units with Model 1040C, a portable, field-ready unit featuring eight key calibration functions.
-
product
Three-Phase HV Vacuum Contactors & Circuit Breakers
B-1005/6
*Three Phase*Upright or Low Profile for High Reliability*½ to 2 Cycle Trip & Interrupt*208V to 38kV Operate*200 to 1,200A Continuous*2,000 to 28,000A Interrupt*Line or Energy Storage Close & Trip*Ideal for High Power Electronics*High Speed Sealed Arc Interrupting*High Speed Crobar Shorting*Compact, Light Weight*Long Life*Minimum Reignitions*Minimum Restrikes
-
product
Turn-Key Short Circuit Laboratories
For low and medium voltage switchgear including :*Circuit breakers*Contactors*Disconnect switches*Fuses*Miniature circuit breakersApplied tests for low and medium voltage switchgear :*Dielectric withstand test*Impulse withstand test*Breaking capacity test*Mechanical life testElectrical life test*Over load performance test*Short circuit breaking capacity test**Short time short circuit impulse current test*Temperature rise test*Operation performance testTests for low & medium voltage panels :*Short time short circuit impulse current test*Dielectric test*Impulse withstand voltage test*Temperature rise test
-
product
100 Amp Intelligent Power Management
IPMDS100
- Intelligent Power Management System- 3 - 20 Amp Single Phase Outlets- 3 - 40 Amp Three Phase Outlets- 2 - 60 Amp Three Phase Outlets- Automatic Load Shedding- 100 Amp Mil Spec Input and Output Connector- Easy Access Circuit Breakers- Phase Over Current Protection- Low Voltage Warning- Built In Press to Test
-
product
Current Transformers
Rishabh Instruments Pvt. Ltd.,
Rish Nano CT is a very reliable, efficient and robust current transformer for measurement of AC current. It provides 100 mA AC output. It can be used in Circuit breakers. Earth Leakage Protection.
-
product
Circuit Breaker Tester
GDGK-307
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1) Closing and opening time measurement of 12 channels2) Max difference of closing or opening time measurement of three phases3) C-O and O-C time measurement4) Rated operation sequence test5) Bounce time and frequency measurement of breaker closing6) Circuit breaker closing and opening speed measurement7) Travel-time, coil current-time curve of circuit breaker operation measurement8) Travel and clearance of circuit breaker measurement9) Variable DC circuit breaker operation power supply10) Closing arc resistance value and connected time measurement11) Closing time and opening time of graphite circuit breaker measurement12) Print test results by internal micro printers
-
product
Circuit Breaker Tester
GDGK-303
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1) Closing and opening time measurement of 12 channels2) Max difference of closing or opening time measurement of three phases3) Bounce time and frequency measurement of breaker closing4) Circuit breaker closing and opening speed measurement5) Travel-time, Coil current-time curve of circuit breaker operation measurement6) Clearance of circuit breaker measurement7) Variable DC circuit breaker operation power supply8) Print test results by internal micro printers
-
product
250 A Molded Case Circuit Breaker Tester
MCCB-250
The Vanguard MCCB-250 is a programmable, high-current source designed specifically for testing molded-case circuit breakers, thermal magnetic and solid-state overload motor-protection relays.
-
product
Automatic Circuit Breaker Timer Kit With Printer
NMC OFFERS FULLY AUTOMATIC CIRCUIT BREAKER TIMER KIT WITH IN BUILT PRINTER AND COMPUTER INTERFACE.
-
product
Circuit Protection
Mors Smitt offers a wide range of railway hydraulic magnetic circuit breakers. The circuit breakers are fully configurable to meet individual requirements.
-
product
Digital Earth Resistance Testers
ST-1520
Capable of measuring earth voltage.2mA measuring current permits the testing of earth resistance without tripping earth leakage current circuit breakers in the circuit.Auto power off function.The timer operates automatically for approximately three to five minutes when the "push button switch" and "timer on button" are pressed together.
-
product
Circuit Breaker Analyzer
CBA 3000
CBA 3000 allows any timing test, motion and speed analysis, multiple contemporary static and dynamic contact resistance measurements, both sides grounded (BSG) tests, undervoltage condition test and more. All these functions are integrated in a single lightweight test case without the need of connecting additional external modules.
-
product
3 Wire (Digital) Earth Resistance Tester
4120 ER
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Battery test indication.● Calibration performed with supplied test leads.
-
product
Circuit Breaker Test Equipment
DV Power has released a new generation of circuit breaker test equipment for condition assessment of medium and high voltage circuit breakers.Field-portable instruments with standalone or PC controlled functionality, allow performing various tests during circuit breaker manufacturing, commissioning and maintenance stages.Applications supported by the DV Power test equipment include measurements of:Contact resistanceDRM (dynamic resistance measurement)Coil resistance and coil current (IEC 62271-1...show more -
product
Surge Arrester Testing
Weshine Electric Manufacturing Co., Ltd
This instrument can be widely used in equipment maintenance of substations and power plants, and to measure insulation resistance, absorption ratio and polarization index of high-voltage electrical equipment such as transformers, reactors, capacitors, and circuit breakers. The leakage current of the low-voltage arrester of the power distribution cabinet is automatically tested.
-
product
Circuit Breaker Testing
HAOMAI Electric Test Equipment Co., Ltd.
Circuit Breaker Testing is utilised to test the operation of each switching systems and the programming of the entire tripping structure.
-
product
External Load Module
ELM
Circuit breakers are often overlooked during maintenance of electrical systems in aircraft, or often only verified for open and closed states. To test the true functional purpose of a circuit breaker it requires the application of current in excess of the rated trip value and then measure the time for the breaker to actually trip. This is the only way to verify that a circuit breaker will react as designed if an electrical failure occurs.
-
product
Circuit Breaker Testing Equipment (SCOT Series)
SCOT MXP+
SCOT MXP+ measures, displays and prints CLOSE, OPEN and CLOSE-OPEN time of 2 Main + 2 PIR contacts per pole, 3 poles simultaneously, ensuring measurement of 6 Main + 6 PIR contacts simultaneously. Ideally suitable for CBs having PIR contacts & multiple breaks per pole
