-
Product
HV AC Test Set
SERIES S400 TYPE RX I O/ I OACP
-
K&S Engineering and Scientific Ltd
The output is continuously variable from zero to 10 kV by means of the panel mounted regulator. An output trip is fitted which operates when the output exceeds 25 mA switches off the test set and operates a neon overload indicator. Primary protection is provided by two panel mounted fuses. The output is protected by the output trip and a magnetic/hydraulic circuit breaker.
-
Product
External Load Module
ELM
-
Circuit breakers are often overlooked during maintenance of electrical systems in aircraft, or often only verified for open and closed states. To test the true functional purpose of a circuit breaker it requires the application of current in excess of the rated trip value and then measure the time for the breaker to actually trip. This is the only way to verify that a circuit breaker will react as designed if an electrical failure occurs.
-
Product
Electrical Circuit Protection - Breakers
-
Eaton’s complete line up of low and medium voltage circuit breakers and fuses are used to provide circuit protection in alternative energy, commercial, industrial, mining, and military applications, where they protect against overloads and short circuits in conductors. These circuit breakers are applied in panelboards, switchboards, motor control centers, control panels, combination starters, individual enclosures, and bus duct plug-in units.
-
Product
Circuit Breaker Testing Equipment
CB SCOPE
-
SCOPE introduces CB SCOPE – Loco Vaccum Circuit Breaker Test System; the ultimate solution for testing Loco Circuit Breakers of all types. CB SCOPE is the most complete analyzer for checking the dynamic performance of LOCO VCB’s.
-
Product
Modbus Gateway With Ethernet for Woodward GCP-30 Genset Controls and LS 4 Controls
GCP-MG
-
GCP-MG is a next-generation Modbus/CAN gateway specifically designed to interface Woodward's GCP-30 series genset controls (GCP-31, GCP-32), and LS 4 circuit breaker controls with Modbus networks. The GCP-MG gateway has been developed in cooperation with Woodward to ensure the highest possible degree of interoperability with Woodward equipment.
-
Product
Primary Injection Testers
AT-10B
-
ETI’s AT-10B autotransformer steps-down 480V outputs to 240V outputs. This portable autotransformer allows ETI’s PI-1600 or PI-800 circuit breaker testers to be used at full-capacity on 240 and 480 VAC lines. The unit provides 240 VAC at 10 kVA, is housed in a rugged ABS enclosure approximately 22″ x 11″ x 22″, and weighs less than 125 lbs.
-
Product
Circuit Breakers for Panelboard and Controlboard
-
Mitsubishi Electric Automation, Inc
Series of MCCB and ELCB that provide maximum protection in a small frame size. A complete product offering for equipment control cabinets and distribution panels.
-
Product
Coil Analyzers & Power Supplies
-
Coil analyzers and power supply units are portable and lightweight devices intended for use in harsh switchyard and industrial environments. The typical application is switchgear and circuit breaker testing when substation battery is not connected or available. An advantage over substation battery is enabled testing in under-voltage and over-voltage conditions. Furthermore, the stable voltage outputs with a very low ripple (<0,5%) enable an analysis of the coil and motor current graphs recorded with circuit breaker analyzers from different vendors.SAT40AD, POB30AD, and POB40AD are unique devices in the market due to their dual purpose:Power supply for coils and spring-charging motorsTesting circuit breaker’s coils, motor, and auxiliary circuitAll DV Power coil analyzers and power supply units have four separate outputs for opening and closing coils.SAT40AD has two powerful motor outputs (AC and DC) which can withstand up to 40 A inrush current.POB30AD and POB40AD have DC motor output rated up to 30 A and 40 A respectively. With the use of motor outputs, POB and SAT can also be used as a power source or a temporary battery charger.SAT40A II series instruments can be controlled via PC. The DV-Win application software is used to control both SAT and CAT (Circuit Breaker Analyzers & Timers) devices at the same time, making a unique test system for switchgear and circuit breaker testing.
-
Product
Non-Contact Voltage Tester
NCVT-1
-
Non-contact detection of voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets, and wires.High intensity, bright green LED indicates the tester is operational and aids in illuminating the workspace.When voltage is detected, a high intensity, bright red LED illuminates and a warning tone sounds.Discrete digitally controlled ON/OFF power button.Auto power-off feature conserves and extends battery life.Microprocessor controlled low-battery indicator and tester shutdown.CAT IV 1000 Volt safety rating provides expanded operation and protection.
-
Product
Loop / PFC Testers
-
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2715 is a loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
Product
Auto Reclose and Sync Check
-
Operating records for overhead power lines reveal that most faults are of a transient nature (e.g. lightning induced) & that service interruptions may be minimized by use of automatic reclosing of circuit breakers. An automatic reclosure of the circuit breaker, after the fault clears, provides improved service continuity & system stability. The 1B230 Series Reclose Relay provides for single or double shot automatic reclosing of circuit breakers, following interruption of supply due to a fault in the system.
-
Product
Dynamic Contact Resistance Meter
-
Dynamic contact resistance measurements are necessary to understand the condition of the arcing contacts of the circuit breaker. Static contact resistance measurements do not give us information related to erosion of arcing contact, misalignments of the contact, and damages to the driving mechanism.
-
Product
Primary Injection Test Set
PI-6000
-
The PI-6000 is a rugged & durable primary injection test set capable of testing circuit breakers up to 6,000 amperes frame size. It incorporates an output transformer with dual primaries to facilitate its use on power sources of 480 VAC as well as 208-240 VAC. The unit also includes dual secondaries to provide optimal impedance matching to a wide range of circuit breaker sizes. An internal voltage sensor automatically configures the AC control power section to be energized only when properly configured for the applied voltage.
-
Product
Contacts Resistance Tester
JYK II
-
•Instrument IPC architecture for domestic production of all models of metal contacts SF6 switchgear, GIS combination of electrical, vacuum switch, oil switch and column switches, contacts and so on.•Sensor: Acceleration speed sensor, rotation speed sensor, linear stroke sensorinstallation is very easy and simple.•Trigger: The trigger, external trigger, the sensor is triggered. Sensor can trigger the circuit breaker manually switching characteristic test, such as a manual column pole division switch.
-
Product
Miniature Circuit Breakers
-
Miniature circuit breakers are applied to protect electric applications against an over current. When an electrical circuit is not protected the application can be damaged and unsafe situations may happen like fire. Mors Smitt delivers a wide range of miniature circuit breakers specially designed and tested according to railway regulations.
-
Product
AC and DC 20-Amp Power Supply
ACDC-20
-
The ETI Model ACDC-20 is a rugged and portable 20-amp AC and DC power supply. Its applications include resetting circuit breaker charging motors and other general purposes. It will provide DC voltage in three nominal ranges from 0-120V, 240V, and 480V at 1.92 kVA, as well as AC voltage in three nominal ranges from 0-140V, 280V, and 560V at 2.8 kVA. The ACDC-20 is housed in a rugged plastic enclosure approximately 21.5” x 18.5” x 11.5” and weighs approximately 115 lbs.
-
Product
Adjustable Test Stab Set
-
The ETI adjustable test stab set may be used with your high-current circuit breaker testers to maximize efficiency and convenience for testing multiple breakers. Our stab system allows your technicians to test breakers in-place and avoid jacking breakers up or down for testing. By combining mobility and flexibility into one simple system, this stab set is a proven improvement over conventional designs. The components in the adjustable stab set are made of 120 pounds of 110 copper.
-
Product
Circuit Breaker Testing Equipment
HISAC Ultima
-
HISAC Ultima – new generation Circuit Breaker Dynamic Test Set from SCOPE …. The ultimate solution for testing Circuit Breakers of all types. HISAC Ultima is the most complete analyser for checking the dynamic performance of CBs in live EHV switchyards upto 765 kV. HISAC Ultima can carry out Dynamic Contact Resistance Measurement on SIX breaks of THREE poles in one operation thereby significantly reducing stress on CB & testing downtime.
-
Product
Standalone Sporadic Event Recorder For Circuit Breakers
OTM-XB
-
The OTM-XB is the only standalone recorder to use the vibro-acoustic method that detects intermittent and sporadic operational faults on working circuit breakers.
-
Product
3 Phase Relay Test Set
-
This is a portable Relay Testing Set suitable for testing different types like over current, earth leakage relays, circuit breakers of 1A – 50A rating etc. All the components are assembled and enclosed with a portable air cooled M.S.cabinet.
-
Product
Power Probe III Set
PP319FTC
-
Full functioning voltmeter measures in 1/10th of a volt increments from 1/10th of 1V up to 70V. Easy to read dual polarity indicators: red (+) symbol indicates positive green (-) symbol indicates negative. Circuit breaker protects the vehicles electrical system and your Power Probe. 20' extension lead gives you 40' total of lead. Great for RV'S, trucks and trailers.
-
Product
Circuit Breaker Testing Equipment (SCOT Series)
SCOT MXP+
-
SCOT MXP+ measures, displays and prints CLOSE, OPEN and CLOSE-OPEN time of 2 Main + 2 PIR contacts per pole, 3 poles simultaneously, ensuring measurement of 6 Main + 6 PIR contacts simultaneously. Ideally suitable for CBs having PIR contacts & multiple breaks per pole
-
Product
Primary Current Injection Test Sets
-
Our primary current injection test sets cover from 750A through to 6000A. Available in single phase, testing applications include testing and timing of under and over current relays, circuit breakers and CT ratio testing.
-
Product
Voltage Detectors & Others
-
Voltage Detectors, Circuit Breaker finder, Portable working lamp are Indispensable equipment which must always accompany the technician. Its essential characteristics are an extreme handiness, a very high protection degree and easiness of use.
-
Product
Contact Resistance Meter
-
The Motwane Manufacturing Company
High contact resistance values are a definite cause of the failure or less than optimal performance in a wide variety of electrical devices. Contact resistance testing is therefore most critical to measure the resistance of electrical connections in switching devices, circuit breakers, isolators, busbars, relays, joints, connectors, cables, and cable joints. The device helps to find destructive or corroded contacts and hence protects substation devices from damage.
-
Product
Multiple Channel Burn In Power Supply
100PM
-
The most important features of this burn in power supply is its ability to hold a constant output for each channel even in the event that a unit under test on one channel may short and fail. Since each channel has it''s own transformer, no glitches or voltage spikes can get into any of the other channels. This image shows the results as the second channel from the left is shorted with a small wire and the circuit breaker pops out. Used for burn-in testing and other timed testing where power isolation is required. Very basic simple circuit, see schematic below. Cleans and frees up benchtops, burn in racks and work space clutter. Available in benchtop or rackmount.
-
Product
Micro-Ohmmeters
RMO-G Series
-
The RMO-G is a portable micro-ohmmeter designed for contact resistance measurement of non-inductive test objects and applications with increased safety requirement. It tests medium and high-voltage circuit breakers, disconnecting switches, high-current bus bar joints, cable splices, and different high-current links. Due to its Both Sides Grounded and Remote Control functionalities, the instrument accurately measures even in the most demanding environments, providing additional safety to testing personnel.The RMO800G is the most powerful portable micro-ohmmeter on the market with 800 A output current. RMO200G is our best seller in the USA. A user can choose the appropriate model depending on the output current requirement, from 100 A (RMO100G) to 800 A (RMO800G).We use an unbreakable plastic case with IP67 protective rating (with closed lid) for instruments’ housing. Although very portable and lightweight, RMO-G micro-ohmmeters have very high output power capabilities. High output voltage enables a wider measurement range at higher test currents. Consequently, it enables the usage of thinner/longer test cables. RMO-G generates a true DC ripple-free (less than 1 % ripple) current with automatically regulated test ramps. During the testing, it increases current before measuring and decreases current after the measurement. This significantly decreases magnetic transients and ensures great accuracy.Special current clamps measure a current through groundings when the instrument tests in Both Sides Grounded conditions. The instrument itself powers these clamps. If even higher safety level is required, the Remote Control feature enables the operator to perform measurements from distant locations.RMO-G instruments can store up to 500 measurements in internal memory. Also, they have a built-in thermal printer and USB flash drive available as an option. An additional option is the built-in High Precision module suitable for measurement of very low resistance, in the range from 1 to 30 µΩ, with 0,01 µΩ resolution.Our free DV Win software communicates with the RMO-G micro-ohmmeters via USB or RS232 interface. It allows a user to run the test remotely from a PC. Also, a user can download test results, analyze and generate fully configurable test reports through the software.
-
Product
Powerful AC/DC Power Supply For Testing Circuit Breakers
POB35AD
-
POB35AD is a power supply unit employing the latest power electronics technology. POB35AD generates ripple free DC-voltage and it is developed for regular maintenance tests of power circuit breakers. It eliminates use of stationary batteries during testing. Output voltage is selectable from 10 to 250V AC/300VDC. The test set is a powerful and versatile unit with possibility to generate up to 30A.
-
Product
Ground-Fault Location Products for Ungrounded Systems
-
When combined with Bender's ground-fault detectors and current transformers, EDS series modules provide fast, automatic ground-fault location in ungrounded systems. Fault location takes place while the system remains online without the need to open branch circuit breakers or disconnect equipment. Bender's fault location system works on both AC and DC systems, as well as systems with variable frequency drives. A standalone, portable fault location system is also available.
-
Product
Switch Analyser Unit
SA5A
-
The SA5A has been developed for professionals users that wish to fully analyse their medium voltage circuit breakers.
