Cables
See Also: Cable Assemblies, Cable
-
product
Cable Fault Locator
TX2001
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3000m (10,000ft) 50, 75 & 100 ohm Selectable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
product
RS485 Null-Modem Cable, DB-9 Female to DB-9 Female, 1m
183283-01
9-Pin Female DB-9 to 9-Pin Female DB-9 Serial Cable - The 9F-9F Serial Cable, sometimes referred to as GPIB Serial Cable, connects and controls GPIB devices using RS232 and RS485 serial ports. The 9F-9F Serial Cable is offered in different lengths.
-
product
Flexible x1 PCI Express Riser
SKU-039-XX
The Flexible x1 PCI Express Riser (Riser) was designed to extend the x1 PCI Express bus. The Riser includes an x1 PCI Express adapter board (optional: x4 PCI Express adapter), x1 PCI Express host board and a 12” PCI Express Flat cable.
-
product
PCI Converter
ES-200
The eSATA PCI BRACKET takes the blazing speed of eSATA outside your computer case with this external plate adapter. Simply install the PCI plate in an open PCI slot on your computer and attach the SATA cable to an available motherboard connector. Now you have an external eSATA port.
-
product
Optical Fiber Identifier
TM301
TM301 Optical Fiber Identifier (Live Fiber Detector) is an essential instrument for the installation and maintenance of optical fiber projects. It can easily detect any spot of SM fiber cables. Through inserting a 1310 or 1550 modulated signal into the fiber, it is used to indicate the direction of the transmitting signals, find and locate the specific fiber without interrupting the normal work during the installation, cabling and maintenance.
-
product
Fiber Optic Type Chemical Solution Concentration Monitor
CS-100F1 Series
The CS-100F1 Series is equipped with fiber optics cable based on the CS-100 Series. It offers real-time, in-line measurements by directly integrating the sample cell into the cleaning system piping and by using a fiber optic cable for light signal transmission. A single concentration monitor can take up to four measurements and monitoring of multiple chemical solutions in a single-bath or single-wafer cleaning system is also possible.
-
product
19" Breakout & Power Input Panel
Cabinet CP-103
The CP-103 is breakout and power input panel which is used to provide a clear connection interface for 19” racks. It is equipped with the most common interfaces found on industrial computers. In addition, it provides a single phase 16A CEE connector and a brush to feed through additional cables and tubes. Furthermore, it’s M6 threaded plate installed to simplify equipotential bonding.
-
product
OTDR Launch Cable Box, OTDR Dead Zone Eliminator, 1KM-2KM
Shanghai Fibretool Technology Co.,Ltd.
Designed to aid in the testing of fiber optic cable when using an OTDR. TheOTDR Launch Cable Box is used with Optical Time Domain Reflectometers (OTDRs) to help minimize the effects of the OTDRs launch pulse on measurement uncertainty. Available in many different configurations and fiber lengths.
-
product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 2m, 250 Port
A500RMR-05F050D4B200
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Ferrules, 0.5m HV, Exit Towards Pin 1
A050DF5-F-HA050
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
RH+T+Tdp Cable Probe
T3111-4
Relative humidity, temperature sensors at probe on the cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
75 Ohm BNC to MCX Cable Adaptor Assemblies - 2GHz
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Cable Assy 25-Pin D-Type M/M 0.5m
40-970-025-0.5m-MM
The 25-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 25-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
Universal LightProbe Connector Cables
ULP-CC
Provides fool-proof sensor wiring with color-coded and labeled wires, corresponding to sensor pin labeling, with separate sheathing of individual sensor wires for easy identification at the ATE interface. These will save time and over-all assembly cost, and are long, durable and tested.
-
product
Manual Model for Integrated use in VLT Test Lanes
VLT 0939TL01
Manual Headlight Beam Tester with Same measuring Techniques as our Fully Automated models. This Manual operated model for use in VLT Test Lanes, with cable boom connection to the Test lane Computer. Including rechargeable battery pack and charge.
-
product
Cable Plant Monitoring
Promptlink Communications, Inc.
Cable Plant Monitoring (CPM) is a real-time network device management tool for your DOCSIS network. CPM handles all of your DOCSIS cable modems, Wireless CMs, eMTA and Cable Modem Termination Systems (CMTS) along with monitoring fiber nodes. This allows you to readily see network problems, troubleshoot customer access issues, and easily deal with difficult management efforts, including upgrading CPE firmware on a very large scale.
-
product
68-Pin VHDCI Cable Assembly, Male to Unterminated With Tinned Ends, 1m
A068VMR-T-6C100
The male cable assembly is suited for direct connection to various products using the 68 Way VHDCI connector.
-
product
2-port/4-port PCI Express GigE Frame Grabber Card
AX92320
The AX92320 supports PCI Express x4 lane, two or four independent Gigabit 802.3at (PoE, Power-over-Ethernet) compliant Ethernet ports and GigE Vision camera compliance. The PCI Express x4 frame grabber can provide up to 30 watts at 54 VDC power to port which allows power to be supplied to connected PoE-based devices, such as GigE Vision cameras in machine vision systems. The intelligent GigE Vision card also supports IEEE 1588 (precise time protocol), enabling synchronization with multi-camera acquisition. Combining IEEE 1588 and PoE function, the card utilizes a single Ethernet cable for power, data, and synchronization. Furthermore, it supports jumbo frames up to 9.5KB. The AX92320 is ideal for PoE applications such as automated optical inspection (AOI), factory automation, and PC-based surveillance systems.
-
product
20-Pin GMCT Cable, Male to Female, 10A, 0.5m
A020GMR-020GFR-0B050
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 20-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
Upgrade - Accessory Kit For 34460A - Test Leads, USB Cable
3446ACCU
3446ACCU provides the accessory kit for the 34460A, including the test leads and USB cable.
-
product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Tinned Ends, 0.5m, 90º
A1604FT-T-0A050
For applications where a 90 degree down cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
product
IT Infrastructure, Asset And Connectivity Management System
CableSolve is an enterprise ready Connectivity and Infrastructure Management System that provides portable and end-to end management, and documentation of the IT infrastructure and network connectivity. Manage your entire physical infrastructure from the structured cabling to the switches, routers, and PABX’s all the way to the outlets, desktop PCs and telephones. The desktop component provides end-to-end management, reporting and control while providing portable management of the connectivity infrastructure with the use of one or more Pocket PCs with integrated barcode scanner for extra mobility and flexibility.
-
product
78-Pin D-Type Male Breakout DIN Rail
40-967-078-M
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination, provide a suitable method of restraining the cables, and ensure appropriate electrical safety precautions are observed.
-
product
160 Pin DIN 41612 Cables - Connector to Connector for Pickering
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 160-pin DIN 41612 connector.
-
product
50 Ohm UWave SMA To UWave SMA Cable Assemblies - 26.5GHz
50 Ohm uWave SMA to uWave SMA Cable Assemblies - 26.5GHz
-
product
4-axis Pulse Train Motion Control Modules
HSL-4XMO
HSL-4XMO is an advanced 4-axis remote motion control module via HSL bus. Combined with HSL I/O and motion control modules, it can meet many requirements in machine automation (MA) field. HSL-4XMO offers two models - HSL-4XMO-CG-N/P and HSL-4XMO-CD-N/P. HSL-4XMO-CG-N/P is suitable for steppers and linear motors. HSL-4XMO-CD-N/P is suitable for servo motors with transfer cable. Except the advanced motion control library (refer to PCI-8164), ADLINK also provides two extra features for users. Motion Point Table Managements can let users assign the points into the module in advance. Then, users can issue command to continuously move the points without consuming CPU resource. Motion Script Download provides users a easy interface to program the application. With this script, the DSP inside HSL-4XMO can decode the file and execute itself.
-
product
20-Pin GMCT Cable, Male to Female, 10A, 1m
A020GMR-020GFR-0B100
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 20-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
Flexible x4 PCI Express 4-Way Splitter
SKU-042-XX
The Flexible x4 PCI Express 4-Way Splitter was designed to expand your modern motherboard (ATX, mini ATX, etc.) with a limited number of PCI Express connectors. It allows you to connect up to four x1 / x4 / x16 PCI Express boards to your motherboard’s x4/x8/x16 PCI Express connector.The Splitter includes four x1 (or x4, or x16) PCI Express adapter boards with PCI Express flat ”ribbon” cables, and one x4 PCI Express host board.
-
product
“Floppy drive” Power Cable
SKU-043-03
Female 4-pin “floppy drive” power connectors are on both ends of this cable.
-
product
Industrial Ethernet Network
CC Link IE Field
CC-Link IE Field network is the first gigabit industrial Ethernet network extended down to the field device level. It combines the best of existing technologies and applies them in a highly reliable architecture that provides exceptional data bandwidth and transaction rates. The new network uses commercially available Cat5E cable and RJ45 connectors.
