Showing results: 196 - 210 of 276 items found.
-
RapidTrace 1100 -
Vonaq Ltd
*This TDR / Cable Fault Locator is suitable for testing all Communication CAT (3-6) , Power Cabling , coaxial and mains power cabling*The RapidTrace 1100 TDR / Cable Fault Locator has a 11 measurement ranges from 0.5m to 3500m (3.5km) and is accurate to 1%*The TDR / Cable Fault Locator has 25, 50, 75 & 100ohm Selectable Cable Impedances*Using pre determined gain and pulse width on the TDR / Cable Fault Locator, all major operating and setting parameters can be easily accessed
-
TV One
The ultimate zero latency, scalable, 4K60 solution. Pathfinder provides a zero latency, 4K KVM extension and switching solution. Extend 4K and HD sources via CAT or Fiber cable to create flexible, wide reaching KVM over IP matrixing solutions. Highly scalable, with up to 3,000+ high-quality endpoints in a single system, it’s the perfect solution for mission critical control and collaboration. Pathfinder offers plug and play set up with no configuration of endpoints required, nor any costly user licensing fees.
-
U1600 Series -
Keysight Technologies
3 in 1 dual-channel handheld oscilloscopes with a built-in DMM and data loggerSafely perform high-power signal analysis with CAT III 600V channel-to-channel isolationClearly view details with up to 200 MSa/s sample rate and 2 Mpts memoryEasily identify problem areas and zoom in for more detailed analysis using dual window zoomDebug under any lighting condition with three viewing modes (indoor, outdoor, night vision)10 selectable localized user interfacesUSB 2.0 full speed IO interface
-
PPDCM80 -
Power Probe Group, Inc.
The Power Probe Digital Clamp Meter is an 80amp, auto-ranging clamp meter designed specifically for the automotive technician. This meter is rated CAT III 600V and can measure Volts, Amps, Ohms, Frequency and Temperature, necessary for automotive electrical testing. This meter’s diagnostic applications include (but are not limited to) Parasitic Draw, Crank Current testing and HVAC Temperature testing.
-
Extech MG500 -
Extech Instruments Corporation
The MG500 is a digital high voltage insulation tester that tests voltage up to 10kV and measures insulation resistance to 500GOhm. The MG500 has a CAT III 300 Volt safety rating. This product is complete with a year warranty, built-in heavy duty carrying case with cover, test leads, alligator clips, and 8 x C batteries.
-
K-60 -
The Eastern Specialty Company
K-60 KNOPP VOLTAGE TESTER for AC and DC with polarity indicator. Double safety indication is by solenoid and by neon lamp. Knopp’s K-60 Low Impedance Voltage Tester (Cat. 14460) offers portability and ease of use with full protection. These exceptionally versatile and useful tools are backed by a reputation for quality in the design and manufacturing of electrical test equipment.
-
Panasonic Automotive & Industrial Systems Europe GmbH
Main unit expandable with up to 3 expansion unitsEach unit can measure up to 2 circuits (8 circuits with 3 expansion units)Accuracy: 0.2% for V, I and 0.5% for kWhPower quality measurements (THD and harmonic analysis up to the 31st order)Bidirectional energy measurement (energy produced and energy consumed)Demand measurementWeb server functionality integratedNo hub switch required2 Ethernet ports, 1 RS485 interface1 input, 2 outputsHour meter functionalityDIN rail mountingQuick wiring thanks to push-in terminalsIEC61010-1 CAT III
-
Conductor Analysis Technologies, Inc
The OM Thermal Stress System is a cost-effective performance based reliability test methodology which performs convection reflow assembly simulation and air-to-air thermal cycling. The methodology is utilized by both the IPC PCQR and the IPC 6012-QLM programs. OM systems are available for sale or lease, and test services are provided from both CAT and our service partners.
-
GOLDSUN Electronics Co., Ltd.
The Tester can check UTP and STP Cat 5E,6,6A and Coaxial Cable. It can ldentify and locate the distance of a open or Short Circuit. With the Multifunction Tester you can determine the Continuity and Wiring of the Cable Pattern. Comes with the Low Battery Indicator. It uses TDR ( Time Domain Reflectometer ) to measure the length and distance of the cable. LCD Backlight Display.There are 8 Remote ID available.
-
Extech PQ1000 -
Extech Instruments Corporation
The Extech PQ1000 is a CAT IV Test Lead accessory kit For PQ3400 series power analyzers. It includes a set of 4, 3 m (10 ft) test leads (black, red, blue, yellow) with shrouded banana plugs on both ends (right angle on one end). Includes test probes, alligator clips, and long reach spring loaded clips.
-
C.A 762 -
Chauvin Arnoux Metrix
The CA 762 Voltage Absence Tester is an essential tool for any electrician to check that no voltage is present before working on an electrical installation connected to the network. It complies with IEC 61243-3 Edition 3 and can be used to work on any indoor or outdoor 600 V CAT IV installation. To fulfil the requirements of the standards and legislation in certain countries, there are 2 references, with or without IP2X accessories.
-
1944 -
Peaceful Thriving Enterprise Co Ltd
*With UKCA Approval.*Test for 230VAC circuits.*Neon indicators.*RCD Test.*30mA leakage current measurement.*Detect faulty wiring status in 3 wire receptacle.*Various combinations of 3 neon idnicators tell if wiring is OK or 6 possible faulty conditions.*Power Plug type: UK 13A socket-outlet*Measurement Category: CAT II / 1.5W*Frequency: 50Hz
-
C.A 742 -
Chauvin Arnoux Metrix
The C.A 742 Voltage Absence Tester is an essential tool for any electrician to check that no voltage is present before working on an electrical installation connected to the network. It complies with IEC 61243-3 Edition 3 and can be used to work on any indoor or outdoor 600 V CAT IV installation. To fulfil the requirements of the standards and legislation in certain countries, there are 2 references, with or without IP2X accessories.
-
LVD2 -
Fluke Corporation
LVD2 volt light, offered by Fluke combines a non-contact AC voltage detector and LED flashlight into one easy to use pen-style design. It features dual sensitivity detection, turning blue from 1” to 5” (2.54 cm to 12.7 cm) from the source and red when at the source. The LVD2 is a CAT IV 600 V rated and is suitable for commercial and industrial applications.
-
887 PR -
Standard Electric Works Co., Ltd
● Indicates phase rotation. ● Indicates phase presence.● No battery required.● Phase rotation phase presence indicated on large liquid crystal display.● Small, rugged enclosure.● Color coded test leads.● Phase presence indication from as low as 40Vac to as high as 600Vac.● Fused.● Lightweight, robust and compact.● EN 61010-1 CAT III 600V EN 61010-2-032