Showing results: 481 - 495 of 511 items found.
-
ERAVANT
A lens antenna is a directional antenna that uses a shaped piece of microwave-transparent material to bend and focus microwaves by refraction, as an optical lens does for light.[1] Typically it consists of a small feed antenna such as a patch antenna or horn antenna which radiates radio waves, with a piece of dielectric or composite material in front which functions as a converging lens to collimate the radio waves into a beam.[2] Conversely, in a receiving antenna the lens focuses the incoming radio waves onto the feed antenna, which converts them to electric currents which are delivered to a radio receiver. They can also be fed by an array of feed antennas, called a focal plane array (FPA), to create more complicated radiation patterns.
-
Model N360M -
Teledyne Advanced Pollution Instrumentation
The Model N360M measures carbon dioxide (CO2) by comparing infrared energy absorbed by a sample to that absorbed by a reference according to the Beer-Lambert law.The N360M uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb IR. The analyzer passes the IR beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO2 known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO2 in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure. A nitrogen purge system is provided for the GFC wheel assembly to eliminate the effects of ambient CO2, if necessary.
-
Model N360 -
Teledyne Advanced Pollution Instrumentation
The Model N360 measures carbon dioxide (CO2) by comparing infrared energy absorbed by a sample to that absorbed by a reference according to the Beer-Lambert law.The N360 uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb IR. The analyzer passes the IR beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO2 known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO2 in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure. A nitrogen purge system is provided for the GFC wheel assembly to eliminate the effects of ambient CO2, if necessary.
-
HASO3 FAST -
Imagine Optic
Our HASO3 Fast Shack-Hartmann wavefront sensors provide fast accurate and reliable measurements by uniting the standard HASO family's standard functionalities that customers have come to rely on, including absolute measurement, unequalled accuracy and insensitivity to vibration, with an acquisition speed of 905 Hz and a spatial resolution of 14 x 14 microlenses.When coupled with our HASOv3 software package, you can perform both zonal and modal wavefront reconstruction; calculate the PSF*, MTF* and Strehl ratio*; visualize the spot diagram; and obtain the M* parameter. Adaptive optics users can take advantage of our CASAO software package to control adaptive optics loops to compensate for atmospheric turbulence, optimize the focal spots of laser beams and Freespace communications.
-
Thorlabs, Inc.
Welcome to Thorlabs; below you will find links to optical components and systems, a subset of our entire line of photonics products. All single element optical components can be found under the optical elements link with the exception of optical components that have polarization properties since they have a separate link. Multi-element systems like beam expanders and objective lenses as well as interferometers, fiber collimators, reference cells, modulators, and other optical devices can be found by choosing the optical systems link. Thorlabs also manufactures an extensive line of free-space and fiber optic isolators; stock items ship the same day that they are ordered while our custom orders benefit from our streamlined design and manufacturing process, which minimizes lead time.
-
PTR-TOF 6000 X2 -
Ionicon Analytik Ges.m.b.H.
The new PTR-TOF 6000 X2 is our premium PTR-TOF trace VOC analyzer. We conceived a unique system comprising of a novel high-resolution TOF and IONICON’s PTR technology with the new “X2” features, for the ultimate PTR-TOFMS experience. X2 combines the latest generation of performance enhancing tools incl. the ION-BOOSTER funnel as well as the hexapole ION-GUIDE. The ion funnel focuses the ions into the hexapole ion guide which results in nearly lossless transmission of an extremely focused ion beam into the TOF mass spectrometer. This increases the sensitivity dramatically and also improves the instrument’s mass resolving power. Utmost resolution, sensitivity and lowest real-time detection limit are now available in a robust, transportable platform that is smaller and lighter than previous products.
-
ERAVANT
Full band waveguide detectors are GaAs beam lead Schottky diode-based detectors that are specially designed for millimeterwave network analyzer applications. With a proprietary circuitry design and careful diode selection, these zero-biased detectors exhibit high sensitivity and extremely flat output characteristics. The below standard offering covers the frequency range of 18 to 170 GHz and offers a 1 MHz video bandwidth and 1 MΩ video output impedance. The standard models also have the capacity to handle a maximum RF input power of up to +17 dBm. The RF interface of these detectors is a standard waveguide with an integrated Faraday isolator to improve the port VSWR. The output voltage polarity is negative and the connector type is a female SMA. Other configurations are offered as custom models.
-
JOHO18 -
Wuhan JOHO Technology Co., Ltd
JOHO18 Laser Range Finder Featuring with low weight, low signature designator, JOHO18 laser range finder is tend to be used by paramilitary as a stand alone device or integrated into an electro-optical tracker turret. Features and BenefitsLong range up to 18kmFlexibility of use as alone device or working with thermal camera or night visionLightweightTechnical DataRanging300m~18000m (tank: 2.3mx2.3m)Beam divergence 1.2mrad Repeat frequency3Hz, working 1 min, have a rest 1minAccuracy rate98%Wavelength1.064mCommunication interfaceRS-422Power supply24V~30VDCDimension300mm160mm130mmWeight<5kgReliabilityMNBF 20000 timesMTTR 30minEnvironmental parametersVibration5Hz~200Hz~5Hz,1.5g ,3 direction, each direction 12minShock30g, 11ms, 3 vertical axis direction total 18timesWorking temperature-40~+55Storage temperature-55~+70Relative humidity953%35EMCMeet GJB151A relevant requirements.
-
Pacific Millimeter Products
These waveguide bandwidth detectors use silicon beam lead diodes on a planar stripline circuit to obtain an extremely rugged and compact device. Most millimeter wave broadband detectors have very poor VSWR due to the difficulty in obtaining a good wideband impedance match to the diode. To overcome this problem, these detectors utilize two diodes and an internal matched termination and 3 dB hybrid as shown below. This circuit allows a VSWR of 2.0 or better over a full waveguide bandwidth for most of these detectors. Detectors for waveguides WR-8 and smaller use a single zero bias GaAs diode. The high sensitivity zero bias GaAs diodes can also be special ordered for use at lower frequencies when highest sensitivity is required.
-
Wildcat+ 1280 Series -
Xenics
The Wildcat+ 1280 series is based upon a state-of-the-art InGaAs photodiode array with 1280×1024 pixels and 5 μm pixel pitch. The camera offers superior, high-resolution SWIR imaging capabilities, comes in a versatile and industry-proven Wildcat camera package (GenICam compliant) and offers advanced on-board image processing.The Wildcat+ 1280 camera outputs full frame images at 120 Hz via either a CameraLink or USB3 Vision interface.The Wildcat+ 1280 is suitable for semiconductor inspection, display inspection (mobile phone and TV), microscopy and laser beam analysis.Benefits & Features• Compact and industry-proven camera design• High-resolution SWIR imaging• Advanced on-board image processing performance• GenlCam compliant• Flexible optical mount and lens options
-
Wildcat+ 640 Series -
Xenics
The Wildcat+ 640 series is based upon a state-of-the-art InGaAs detector with 640×512 pixels and 20 μm pixel pitch. The camera offers superior, high resolution SWIR imaging capabilities, comes in a versatile and industry-proven Wildcat camera package (GenICam compliant) and offers advanced on-board image processing.The Wildcat+ 640 camera outputs full frame images up to 300 Hz via either a CameraLink or USB3 Vision interface.The Wildcat+ 640 is suitable for semiconductor inspection, display inspection (mobile phone and TV), and laser beam analysis.Benefits & Features- Compact and industry-proven camera design- High-resolution SWIR imaging- Advanced on-board image processing performance- GenICam complaint- Flexible optical mount and lens options
-
X-5000 -
HORIBA, Ltd.
HORIBA continues it's innovation in the petroleum market by proudly teaming with Olympus Innov-X to promote the X-5000 Mobile XRF Analyzer. The X-5000 is a rugged, fully integrated closed beam portable EDXRF system that offers the power and performance of a traditional benchtop XRF, but is designed for transportable operation. Using a Silicone Drift Detector, low PPM detection limits can be achieved for many elements in a variety of sample types and matrices. Applications include fuels, additives, and wear metal oils to crude oils, water, coke, and coal allow this easy to use analyzer to be a fast, flexible solution to traditional testing methods.Detectable elements to concentrations of 100% are: Aluminum, Antimony, Barium, Cadmium, Calcium, Chlorine, Chromium, Copper, Iron, Manganese, Molybdenum, Nickel, Phosphorous, Potassium, Silicon, Silver, Sulfur, Tin, Titanium, Vanadium, and Zinc.
-
MVX -
Dakota Ultrasonics
The MVX finishes the line of MX gauges with class. This thing is loaded with all of the features of the MX gauges and a lot more. Four selectable display options: RF, Rectified, B-Scan, and Large Digits. An internal data logger that stores a total of 12,000 readings and waveforms, 64 user custom definable setups, selectable transducer table for improved linearity, thru paint mode with the single press of a button, multiple calibration and material selection options, and auto waveform find just to mention a few! Equipped with a single element flaw prove-up mode for basic angle beam inspections. This is all nicely packaged in a very mini portable aluminum extrusion for extra durability and portability! The MVXview java-based PC software makes this thing a complete kit, and then some!
-
U Light -
Teledyne Marine Bowtech
The Teledyne Bowtech U light is for use on subsea platforms that operate down to 6000m depths, requiring a 120Vac Ultra- bright 10,000 lumen, LED Floodlight. The 80° wide LED floodlight beam angle is ideal for colour video inspection tasks. Housed in hard anodised aluminium, this deepwater LED floodlight measures in at 82mm Ø by 148.4mm long and comes with thermal protection ensuring that the light does not overheat if accidentally run in air. The U Light has the capability of being controlled externally by normal ON / OFF power switching or by using phase control diming techniques enabling the operator to produce a varying level of light intensity. This extremely robust U Light LED floodlight is ideal for clear visibility in deep depths on larger work class ROVs, Trenchers and Tractors.
-
LumiSun-50 -
Innovations In Optics Inc.
The LumiSun-50™ is a high power, multi-wavelength LED solar simulator that meets IEC 60904-9 Class AAA for spectral match, uniformity of irradiance, and temporal stability. The LumiSun-50 achieves a spatially uniform illumination field from a chip-on-board (COB), multiple-wavelength LED die array. The field of illumination is 50 x 50 mm at a working distance of 200 mm. The LumiSun-50 includes a driver/controller which individually provides constant current to each die in the COB array. Total irradiance of 1.1 sun units is provided and can be decreased to 0.1 suns. The LED light source of the LumiSun-50 is contained within an air-cooled housing that can rotate the angular beam alignment. Adjustment and setting of the optimum light path working distance is visually facilitated by a converging pair of red dot laser pointers.
