Showing results: 301 - 315 of 511 items found.
-
11PD100-Si -
Standa
Silicon detectors provide a generous aperture for laser beams up to 10 mm in diameter. The threaded aperture allows you to install filters, attenuators, fiber optic adapters or other optics that suit your specific needs.
-
Shoghi Communications Ltd.
The Strategic Thuraya Monitoring System is designed to monitor Thuraya Satellite Phones operating on Thuraya-2 or Thuraya-3 Satellites network. The System is capable of providing both sides of the communication (full duplex call), call related information (CRI) along with the location of the Thuraya Phone by monitoring of both L & C-band. The Monitoring of L-band (between Thuraya satellite and Thuraya mobile) and C-band (between Thuraya Satellite and Thuraya Gateway), provides total traffic monitoring of the targeted spot beams each of which are nearly 350 - 400 Km. Normally 7 spot beams are available at any location under the Thuraya footprint.
-
PM203 -
Irradian Ltd.
The PM203 optical power meter can be used to measure the radiometric power in a beam of monochromatic or narrow band light. Using the internal calibration table the micro-processor controlled PM203 displays directly the optical power in Watts or dBm or the calibration wavelength.
-
optek
optek’s electroplating analyzers are inline devices designed to measure plating solution’s metal concentration in real time. These analyzers can be designed to accommodate virtually any concentration range. Operationally, the analyzer passes a white light beam through the plating solution to be monitored. Then, light absorbance is measured at two distinct wavelengths, and the difference in light absorbance between the two wavelengths is equated to a plating solution concentration.
-
AWMF-0108 -
Anokiwave Inc.
The AWMF-0108 is a highly integrated silicon quad core IC intended for 5G phased array applications. The device supports four Tx/Rx radiating elements, includes 5 bit phase and 5 bit gain control for analog RF beam steering, and operates in half duplex fashion to enable a single antenna to support both Tx and Rx operation. The device provides 26 dB gain and +9 dBm output power during transmit mode and 28 dB coherent gain, 5.0 dB NF, and -28 dBm IIP3 during receive mode. Additional features include gain compensation over temperature, temperature reporting, Tx power telemetry, and fast beam switching using eight on-chip beam weight storage registers. The device features ESD protection on all pins, operates from a +1.8 V supply, and is packaged in a 48 lead 6x6 mm QFN for easy installation in planar phased array antennas.
-
W-IE-NE-R, Plein & Baus GmbH
The WIENER 6021 crate series can be outfitted with cPCI, PXI or PXIe backplanes to provide high performance chassis with highly reliable low-noise power supplies for these bus standards. Typical applications are data acquisition, beam line control and test instrumentation.
-
ABET Technologies Inc.
Standard maintenance, lamp, or filter replacement, does not require any tools. Locking indicator dials on all the system controls, located together for ease of alignment, provide for a reproducible setup. A beam imaging accessory makes alignment even faster.
-
Napco Precision Instruments Co
*Output Power: ≤75W*Wavelength: 1064nm*Beam Quality: ㎡<3*Repeat frequency:≤50KHZ*Marking scope: 100mm X 100mm*Marking Depth: ≤0.5mm*Marking Speed: ≤8000mm/min*Min. line width: 0.015mm*Input Power: ≤1.5KW
-
VLT 0939TL01 -
Van Leeuwen Test Systems BV
Manual Headlight Beam Tester with Same measuring Techniques as our Fully Automated models. This Manual operated model for use in VLT Test Lanes, with cable boom connection to the Test lane Computer. Including rechargeable battery pack and charge.
-
VLT 0939 -
Van Leeuwen Test Systems BV
Manual Headlight Beam Tester with Same measuring Techniques as our Fully Automated models. This Manual operated model for use in VLT Test Lanes, with cable boom connection to the Test lane Computer. Including rechargeable battery pack and charge.
-
HBM, Inc
HBM provides the optimal Load Cell or Load Sensor for your application. Beam Load Cells: The All-Rounders For Weighing Technology. Ring-Torsion Load Cells: Low Profile And Powerful. Canister Load Cells: Maximum Capacities Up To 400 t. Single Point Load Cells: The Standard in Scales Manufacturing. Digital Load Cells: Ideal For Dynamic Weighing. Weighing Modules: Pre-assembled For Tank And Silo Weighing.
-
Panasonic Industrial Devices Sales Company of America
The fixed beam of focused light from the Convergent Reflective Type Micro Photoelectric PM2 Sensor enables it to precisely detect an object within a defined sensing range. With the ability to measure independently of the background, the PM2 Sensors are also able to detect dark or slightly reflective objects as well as extremely thin objects (> 0.05mm). These features, combined with its compact and robust design, make the PM2 Sensor suitable for a large number of applications.
-
PM2 -
Panasonic Industrial Devices Sales Company of America
The fixed beam of focused light from the Convergent Reflective Type Micro Photoelectric PM2 Sensor enables it to precisely detect an object within a defined sensing range. With the ability to measure independently of the background, the PM2 Sensors are also able to detect dark or slightly reflective objects as well as extremely thin objects (> 0.05mm). These features, combined with its compact and robust design, make the PM2 Sensor suitable for a large number of applications.
-
Ophir
Laser beams with powers of many tens of kilowatts are becoming increasingly common in today’s industrial applications. However, as the powers increase, the stakes increase as well. In this webinar, we will discuss how to monitor appropriate laser parameters to keep high-power processes stable and predictable.
-
AET Associates, Inc.
X-ray and radioactive devices developed by AET, are widely utilized for medical, industrial and research use. The Compact Pulse X-ray Source can accelerate electron beams in a high-gradient electric field, to produce X-rays. Dose Calibrators are utilized for radioactive examinations and treatments in the medical industry.