Showing results: 1111 - 1125 of 2260 items found.
-
2950 CL -
Standard Electric Works Co., Ltd
● Pocket size.● 4000 counts.● Full automatic measurement. Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (Auto off in 1 minute).
-
2940 CL -
Standard Electric Works Co., Ltd
● Pocket size.● 4000 counts.● Full automatic measurement. Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (Auto off in 1 minute).
-
Super-Boost-All -
Goodall Mfg. LLC
The Super Boost•All® is designed to be mounted on your service vehicle with 2 or 4 auxiliary jump starting batteries to start 12 or 24 volt vehicles. The auxiliary batteries are charged from the service vehicles electrical system through the internally mounted battery separator.
-
72-13550 -
Tenma
*HDMI cable tester with LED status display*Tests for normal/short/open/crossover circuit*Scan/full display testing modes conversion*Single key operation*Manual/auto power off (after 10 minute inactivity)*Low battery indication < 7.2V*HDMI/HDMI-mini interface*9V battery (6F22)*12-month limited warranty *view Terms & Conditions for details
-
710 -
Electronic Specialties Inc.
The #710 will perform variable load testing on 12 volt batteries rated as high as 1000 Cold Cranking Amps. Use this battery tester to simulate actual cranking loads. Also tests alternator charging voltage and relative starter current draw. The #710 features large dual meters to display the battery voltage and load current simultaneously, during the test.
-
1120 ER -
Standard Electric Works Co., Ltd
● Waterproof: IP54● Capable of measuring earth resistance and earth voltage● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test● The test leads are supplied as standard accessories for simplified two-wire measuring system● 0Ω adjustment● Battery operated● Data hold function● Low battery indication
-
Chroma Systems Solutions, Inc.
Power conversion testing for automated test systems, LED drivers, power supply testing, battery testing, and much more.
-
Triplett Test Equipment & Tools
1000A True RMS AC/DC clamp-on meter with a backlit LCD display. It offers a large variety of measurement features including AC/DC Current, AC/DC Voltage, Resistance, Temperature, Capacitance, Continuity, Diode Test and NCV Detector. The rubberized overmolded housing provides impact and drop resistance in a sleek ergonomic design, and the user-friendly Auto Power Off feature helps maximizes battery life. With a CAT III 600V design, it provides superior resistance to damage from transient overvoltages in any demanding industrial setting. The Model 9325 is suited for a variety of industrial and residential applications such as security, electrical, HVAC installations and more. Includes test leads, Type K Temperature probe, 9V battery, and case.
-
FC2000 Series -
ACECO Electronics Corp.
A professional frequency counterFrequency range: 1 Meg ohm and 50 ohm input for full range 10 Hz - 3 GHzWeight: 250 gCase: 100 mm * 68 mm * 31 mm stamped aluminum with black anodized finishBattery: Internal 4 * AA 600 mAH NiCd pack10 digit liquid Crystal DisplayLow power consumption (Average 6 hour battery life)Hold switch to lock displayLow battery indicatorUltra sensitive synchronous detector 16 section bargraph to show RF signal strengthHigh speed 300 MHz direct counter with 0.1 Hz resolution4 selectable gate speedsAutomatic holdMeasure frequency and periodBeeper and LED back light with black anodized finis
-
72-6694 CAL D -
Tenma
The 72-6694 CAL D from Tenma is a current calibrator. It provides quality and accuracy of handheld calibrator of precision current source. It features large LCD display (maximum display counts 1999, 13mm (0.5") digit size). The current calibrator has 006P DC 9V, MN1604/PP3 battery or equivalent alkaline type or heavy duty type power supply. The dimension is 185mm × 78mm × 38mm (7.3" × 3" × 1.5") and weight is 265g/0.58lb (including battery). It has adjustable 0 to 24mA current source, 2 ranges (0 to 19.99mA (0.01mA display resolution, ±(0.25% FS + 1d) accuracy), 0 to 24mA (0.1mA display resolution, ±(0.5% FS + 1d) accuracy).
-
72-6694 CAL DU -
Tenma
The 72-6694 CAL DU from Tenma is a current calibrator. It provides quality and accuracy of handheld calibrator of precision current source. It features large LCD display (maximum display counts 1999, 13mm (0.5") digit size). The current calibrator has 006P DC 9V, MN1604/PP3 battery or equivalent alkaline type or heavy duty type power supply. The dimension is 185mm × 78mm × 38mm (7.3" × 3" × 1.5") and weight is 265g/0.58lb (including battery). It has adjustable 0 to 24mA current source, 2 ranges (0 to 19.99mA (0.01mA display resolution, ±(0.25% FS + 1d) accuracy), 0 to 24mA (0.1mA display resolution, ±(0.5% FS + 1d) accuracy).
-
Extech TM26 -
Extech Instruments Corporation
The TM26 is an NSF certified Temperature Indicator with long stainless steel penetration probe for measuring in liquids, pastes, and semi-solid food. Ideal for use in food industry, agriculture, and laboratories. Thermometer can be used on desktops with its removable foot stand or can be mounted on wall or metal surfaces with its magnetic back. Meter features ±1.8°F/1°C basic accuracy with 0.1° max resolution, Displays Min/Max reading with reset function, Data Hold freezes current reading on display, Low battery indication, a magnetic back that can be mounted on a metal surface and Waterproof housing to meet an IP65 rating. Complete with magentic back, foot stand, temperature sensor, and a CR2032 3V button battery.
-
72-13500 -
Tenma
*Digital multimeter with 2000 counts display*CAT II 1000V, CAT III 600V safety rating*Manual function select and manual ranging*Data hold*Full icon display*Powered by 9V battery (6F22)*12-month limited warranty *view Terms & Conditions for details
-
MEET International Ltd.
*Stud Detector (auto calibration)** detects 2"x4" inches stud upto 18mm thickness of drywall** Low battery warning (for stud detection)** Auto Calibration*Metal / ACV / Continuity Detector**)Detect metal with adjustable sensitivity** Non-contact ACV test** Continuity / Polarity check
-
FLIR K65 -
Teledyne FLIR
The FLIR K65 is the advanced, feature-rich thermal imaging camera you need when NFPA® compliance is a must. With fully sealed connectors and a secured battery, the K65 is designed to be fully compliant with the NFPA 1801-2021 Standard for Thermal Imagers covering usability, image quality, and durability for firefighting.