Showing results: 346 - 360 of 2366 items found.
-
Buckleys Ltd.
Battery boxes can be tested for faults by placing the box on a metal plate. By applying a test voltage to an electrode inside the box, the moulding can be checked thoroughly - particularly at the injection points - and any faults found. Defects will be identified by a spark passing from the electrode, through the defect itself, to earth (the conductive material placed outside the battery box.
-
BTAS-16 -
JFM Engineering
The task of testing an aircraft’s Nickel-Cadmium batteries is complicated and involved because of the high number of cell voltage readings that need to be taken during testing. Taking voltage readings from all 20 cells in the typical nickle-cadmium aviation battery multiple times is laborious and error prone, but must be done to properly estimate the condition of the battery under test.
-
C19 -
Fuzhou Fuguang Electronics Co., Ltd.
C19 series is a portable tester which can quickly inspect battery pack of two-wheel vehicles. It can realize quick inspection and selection of SOH data of battery pack and discharge-charge maintenance. Data can be transferred to the mobile phone APP through Bluetooth forming a statistics report and faulty cell warnings so that further maintenance solutions can be developed in time.
-
41-751-001 -
Pickering Interfaces Ltd.
The 41-751 is a low power battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals than can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Megaron Ltd.
From the beginning of 2006 the verification of measurements of the analyzer of lead-acid chemical sources developed by Company "Megaron" is spent in Test laboratory "Neva-Reglament". The analyzer is intended for the express-estimation of a condition of lead-acid batteries: before the first use of new battery (an estimation of the electric characteristics declared by the manufacturer); during the battery operation (an estimation of a condition and working capacity at real application).
-
KV Hipot Power Test Equipment Co.,Ltd
Battery Regeneration is a portable and compact tester which is used on discharging, charging and activating for disabling individual cell batteries.
-
-
IBEKO Power AB
Performing capacity/discharge test on a high-capacity battery may be challenging since high requirements are set on the discharge system. In cases when discharge test times need to be reduced, high load capacities are required from the discharge system. The battery extra load unit BXL is an additional load unit designed especially for this purpose.It is primarily used with BLU battery testers. However, the unit is a universal add-on device. This means it can be used as an additional load with any other discharge/capacity tester in the market.When discharge current exceeds the capacity of a single BLU device, extra load unit increases discharge capacity. A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way in accordance to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.
-
FST-7000 -
Foresight Electronics Co., Ltd.
Battery Conductance Tester is a portable digital measurement device for testing lead acid stationary batteries health and aging condition precisely within seconds. With the help of this device either single cells / blocks or large, multi group battery banks can be measured within a short time and the precisely measured data are processed and reported by given analyzer software automatically.
-
PRODIGIT Electronics Co, Ltd.
*Easy to see now test progress*Can cycle test*Provide Charge, Discharge, Suspend, FOR, LOOP Mode Select*When Charging, set the stop current to stop charging when fully charged so as to avoid overcharging that will damage the battery. When Discharge, set the stop voltage to stop discharge when discharging to lowest so as to avoid over-discharging that will damage the battery.
-
EC-Series -
Global Energy Innovations, Inc.
The EC1000™ and EC2000™ are the only handheld, Multi-Frequency, ElectroChemical Battery Analyzers on the market using CELScan™ technology. This means they can report both the Electrical (Impedance & Voltage) and Chemical (Sulfation and Dryout) properties of lead acid batteries (VLA, VRLA, GEL). Other battery types (NiCd, NiMH, Lithium-Ion and others) may also be tested using the EC1000™ and EC2000™.
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's battery projectile / burning tester is suitable for testing the flame resistance and flammability of various consumer batteries, such as mobile phones and notebook computers.
-
Landt Instruments, Inc
The following are regular battery tester models for single-cell tests (coin cell/half cell/pouch cell/cylindrical cell, CT2001 & CT3001 Models) and supercapacitor test.
-
MTI Corp.
Real-time welding current monitoringAutomatic alarm system to avoid poor quality weldingArbitrary point restarting after the welding adjustmentThe welding time is less than 1 second and the discharging time for the battery cell is about 1 ms.Welding programmable; It is able to skip welding one or more battery cells by programmingFan cooling the welding needleTwo sides welding at the same timePLC controlEmergency stop and alarm system
-
Bloomy Controls, Inc.
A Battery Management System (BMS) is an embedded unit performing critical battery functions, including cell monitoring and balancing, pack charge and discharge control, safety, and communications. The BMS must be tested early in development to optimize control algorithms, as well as during manufacturing to ensure reliable functionality. Bloomy’s family of BMS test systems provides a consistent platform for engineers to bring a BMS to market faster, and more reliably.