-
product
Osprey PCI Qbus Adapter
9668
Dual-height card plugs into PDP-11 Qbus backplane. Fibrechannel cable plugs into Qbus logic connector on Osprey /TXP. I/O Adapter logic provides Programmed I/O and DMA access to "real" Qbus compatible controllers (those not otherwise emulated).
-
product
Fuel Injection Pressure Tester with Quick Couplers
53900
Quick couplers provide for fast and easy hook-up. Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Tests all Chrysler cars with Multi-port turbos and some TBI. Use on Ford older TBI systems not equipped with small Schrader test valve. Includes Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR). Supplied with instructions in a vinyl pouch.
-
product
Shield
Arduino MKR RGB Shield
Write messages and add graphics with this shield. A ready to use library with examples and methods is available for use to easily write static and scrollable text. You can use this shield to show values from your board and is controllable from the Arduino IoT cloud. No need of solder, or special adapters, just plug the RGB matrix shield on top of your favourite MKR board and you are ready to go!
-
product
Hardware
We offer various hardware that is required at cell sites & DAS installations; Grounding Kits, Angle adapters, Snap in hangars, Stand Off Adapters, Butterfly hangers, Tape, etc.
-
product
C Series Universal Analog Input Module
The C Series Universal Analog Input Module helps you perform multi-purpose measurements. This module includes built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. You also can choose options to measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors.The C Series Uni...show more -
product
GPIB to Parallel Printer Interface
Model 4892B
* Adds a GPIB Interface to Printers with Centronics or IEEE-1284 parallel interfaces. See the compatible printer list. * Replaces obsolete printers and plotters with a current HPGL/PCL5 printer.* Prints and Plots from most Analyzers. * Large 256 kbyte buffer and high speed GPIB interface off-loads the instrument and reduces printing time.* No program changes required.* Rack mountable in 1 U high rack mount kit.* Includes universal VAC Power Adapter and printer cable.
-
product
Connector Adapter
MCA-ST connector adapter for the connection of micro plugThe connector adapter allows the direct connection of fine-pole connectors on circuit carriers or jumpers. The adapter is guided over the connector housing, which overcomes the tolerances of carrier and mounting.
-
product
75 Ohm Mini SMB to 1.0/2.3 Adaptor Assembly
40-978-731-2m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
PXI Pull-Thru Adapter, Wired, QuadraPaddle, 160 Pin Female DIN
510140141-2
PXI Pull-Thru Adapter, Wired, QuadraPaddle, 160 Pin Female DIN
-
product
Build Your Hydrostatic Tester
Start with the basic Model 9901 hydrostatic tester as shown to the left with the following standard equipment:- Hydrostatic test pump, air operated.- 1% ANSI B40.1 Grade 1A stainless steel high pressure gauge.- ANSI B40.1 Grade B air pressure gauge.- Micro adjust precision regulator.- High pressure isolation shutoff valve.- Automatic lubricator.- Stainless steel high pressure manifold.- 1/4" NPT accessory port.- Bleed valve.- Air shutoff valve.- Factory set air pressure relief valve.- 7/16-20 straight thread O-ring boss outlet port (MS33649-04) with -4 male adapter fitting.- 3/4" swivel female hose inlet with strainer.- Stainless steel base plate with rubber feet.
-
product
Transceiver Adapter Module For FlexRIO
Transceiver Adapter Modules for FlexRIO feature multiple inputs, outputs, and digital I/O lines for applications that require the acquisition and generation of IF or baseband signals with in‐line, real‐time processing. Example applications include RF modulation and demodulation, channel emulation, signals intelligence, real‐time spectrum analysis, and software defined radio (SDR). Transceiver Adapter Modules also provide digital I/O capability for interfacing with external hardware.
-
product
Extension Hose for Diesel Compression Testing
34729
Makes for easier diesel compression testing in areas with restricted clearance. Attaches between Cat. No. 34700, Diesel Compression Tester and Tool Aid brand diesel test adapters.
-
product
Flexible MiniPCI Express Riser
SKU-055-0X
The Flexible MiniPCI Express Riser (Riser) was designed to extend the MiniPCI Express bus. The Riser includes a MiniPCI Express adapter board (downstream), MiniPCI Express host board and a 12” PCI Express flat cable.The MiniPCI Express host board connects to the motherboard MiniPCI Express connector.
-
product
Flexible MiniPCI Express to 2 MiniPCI Splitter
SKU-069-2X
Flexible MiniPCI Express to 2 MiniPCI Splitter (Splitter) was designed to expand a modern motherboard (ATX, mini ATX etc.) that doesn’t have the MiniPCI interface. It allows you to connect up to two (2) 124-pin MiniPCI add-in boards to a motherboard’s standard MiniPCI Express connector.Splitter includes 2 MiniPCI Adapter boards, MiniPCI Express Host board and 2 Flat PCI Express Cables.
-
product
PCIe Adapter for XMC
PCIe4LXMCX1
Simple and easy to use. Install PCIe4LXMCX1 into your PCIe system to adapt an XMC card. The XMC can have bezel and or rear IO. Pn4 and/or Pn6 are supported with PCIe8LXMCX1. 8 lanes are routed from the PCIe gold fingers to the XMC position. XMC´s with up to 8 lanes can be used. The PCIe lanes to/from the XMC are routed per PCIe specifications with matched lengths and impedance control.
-
product
NI-5783, 40 MHz Bandwidth Transceiver Adapter Module for FlexRIO
784364-01
The NI‑5783 has DC‑coupled inputs with two variants: an elliptic filter variant optimized for frequency-domain applications and a Butterworth filter variant optimized for time-domain applications. The NI‑5783 is particularly well suited for applications in software defined radio, electronic warfare, high-performance machine control, and medical imaging. The NI‑5783 is compatible only with the PXI FPGA Module for FlexRIO modules that have a Kintex‑7 FPGA and the stand-alone Controller for FlexRIO.
-
product
Ethernet Adapter Supporting up to Twenty ARINC-429 Channels in Any Combination
ES-9810/A0 (RUNET II)
The EXC-9810/Ax is an Ethernet adapter supporting up to twenty ARINC-429 channels in any combination of transmit and/or receive. All of the channels feature error injection and detection.adapter. Its small size and ability to interface through Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the ARINC-429 bus, both in the lab and in the field.The receive channels allow for the storage of all selected labels with status and time tag infor...show more -
product
Compact XMC-to-PCI Express (PCIe) Adapter
9296
Our Compact XMC-to-PCI Express (PCIe) Adapter 8X (Front-Panel I/O Only) (9296) permits use of a VITA 61 (XMC 2.0) device in the smallest possible edge finger PCIe form factor. The length of the adapter is the length of the XMC, while the height is a standard PCIe board, not the low-profile version.
-
product
Charger / Quick Charger / Adapter / LED Driver Test System
6010
6010 Charger / Quick Charger / Adapter / LED Driver Test System is able to meet multi-types power products test requirements,and its multi-U.U.T test simultaneously capability can significantly enhance the production line throughput. It also possess multi-modular combination that includes low noise analog AC source with Triac to simulate output, four sets precision power meter, two or four sets ripple noise / timing measurement module, four sets OVP DC power supply, 3310F series & 3332F/3336F Electronic Load module and unique design 3340F series for LED power driver output test.
-
product
EBIRST 50-pin D-type To 25-pin D-type Adapter
93-005-414
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
PCI Adapter for cPCI
PCI2cPCI-32
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
product
PCIe
M.2 Gen4 Socket3
SCHILLER AUTOMATION GmbH & Co. KG
The PCIe Gen4 M.2 Socket 3 test adapter or test fixture kit facilitates Device and Host compliance testing for PCIe Gen4 M.2 Socket 3 Source and Sink devices.
-
product
SOIC DW-to-20-Pin PLCC
MC145158-2
ADAPTER FOR MOTOROLA. FROM PLCC 20 PIN FN PACKAGE TO SOIC DW PACKAGE. A cost effective means of upgrading to SOJ or SOIC ... without changing your PCB layout.
-
product
Single Port RS232 Serial Communications Compact Flash Card
CF232
The CF232 is a tiny Type I format Compact Flash (CF+) single RS232 asynchronous serial port for your PDA, laptop (with an optional adapter), or desktop (using one of Elan's Desktop PCMCIA adapters). The card automatically configures to become another COM port by using the built-in O.S. drivers that are tried and tested and are optimized to work in the Windows environment.
-
product
Serial Protocol Host Adapter
SPI Storm
This is the primary step for using SPI Storm device. It consists in describing how you would like to access your serial device: whether you would like to write to your device, read from it or do both simultaneously
-
product
Evaluation Kits
Advantech ARM-based starter kit packages are including a main board, cables, power adapter, LED panel and an SD card.
-
product
Multi-Function Cable Tester
T010-001-K
The T010-001-K Multi-Function Cable Tester is an essential tool for cable installers or anyone working in telecom or LAN environments. It allows you to test RJ45 (STP/UTP), RJ11, BNC and USB cable wiring, length, fault and location, as well as common metal wires using the included alligator clip adapter.