-
product
Display Driver Test System
T6391
High-resolution flat-panel displays (LCDs / OLEDs) are becoming increasingly integrated. It is common for today's display driver ICs (DDIs) to contain a multitude of logic/analog circuits to manage advanced operations including touch-sensor functions. At the same time, the rapidly growing applications of LCDs / OLEDs in mobile electronics are driving demand for DDI's with smaller sizes and greater capabilities. These factors present serious IC-testing challenges. ADVANTEST's T6391 system is designed to address these needs along with DDIs' increasing number of pins and faster interfaces.
-
product
Integrating Sphere
The standard test temperature is 25, but high power lamps such as HID lamps and LED outdoor luminaires will produce a lot of heat during the test, thus the temperature inside the integrating sphere can not meet the requirements of IEC standards. Lisun Group designed the Constant Temperatured Integrating Sphere which allows the lamp was tested in a constant air temperature.
-
product
PCIe Compliance Testing
Teledyne LeCroy offers an integrated and automated compliance testing system, approved by the PCI-SIG as a standard tool for Link and Transaction Layer Compliance testing for developers working with the PCIe 4.0 and PCIe 5.0 specification. This solution combines a Summit Z58 or Summit Z516 Exerciser and a PCI Express Test Platform (for testing End-Point devices) This system has been selected by the PCI-SIG as a standard test tool for PCI Express 4.0 and PCI Express 5.0 Link and Transaction Layer Compliance Testing.
-
product
SAS Protocol Test System
Sierra M124A
The SAS Sierra M124A Protocol Test System is Teledyne LeCroy's 7th generation protocol analyzer system that provides 100% accurate protocol capture of both SAS (SAS 3.0) and SATA (SATA 3.0). The industry's most widely used test platform for SAS and SATA features unmatched analysis and debug capabilities to help pinpoint problems at every layer of the protocol.
-
product
SAS Protocol Test System
M124A
The SAS Sierra M124A Protocol Test System is Teledyne LeCroy's 7th generation protocol analyzer system that provides 100% accurate protocol capture of both SAS (SAS 3.0) and SATA (SATA 3.0). The industry's most widely used test platform for SAS and SATA features unmatched analysis and debug capabilities to help pinpoint problems at every layer of the protocol.
-
product
In-Circuit Test (ICT) Fixtures
At Forwessun we support and manufacture In-Circuit Test Fixtures for a range of Test Systems. We regularly build fixtures that are supported on a range of systems including - - HP3070- Agilent- Keysight- GenRad- TeradyneWith over 50 years in the industry, we provide a weatlth of knowledge and support to our customers. We are a global company and can support businesses all over the world with the help of over 30 experienced test engineers.
-
product
Hydrostatic Head Tester
TF163
TESTEX Testing Equipment Systems Ltd.
Hydrostatic Head Tester, used for determining the resistance of fabrics (canvas, coated fabrics, cover cloth, rainproof clothing fabrics, and geotextile materials) and films to water penetration under pressure while firmly clamped in the test rig of standard area.
-
product
Constant Temperature Integrating Sphere
IS-*MT
According to requirement of IEC standards, the standard test temperature is 25℃, but high power lamps such as HID lamps and LED outdoor luminaires will produce a lot of heat during the test, thus the temperature inside the integrating sphere can not meet the requirements of IEC standards. Lisun Group designed the Constant Temperatured Integrating Sphere which allows the lamp was tested in a constant air temperature.
-
product
EV-DO Analysis Using NI PXI RF Test Instruments
NI-RFmx EV-DO
Highly optimized RF measurement experiencePerform physical layer analysis on EV-DO cellular signals including MODACC, ACPR, CHP, OBW, and SEMSimple access to advanced measurement parallelism
-
product
Material Testing
With so many materials and applications in the world, you need to know that you can trust your products are durable and do what your engineers designed them to do. Manufacturers rely on results from hardness testing and international safety standards require materials to have a specific hardness or stiffness. Different metals need to be tested according to different hardness testing standards, whether it’s using a Rockwell, Brinell, Vickers or a Universal machine. Bowers Group have a variety of portable, bench and floor models in our product range to provide a solution for your hardness testing needs, whatever it may be.
-
product
Automated Test Systems
WinSoft designs, develops and integrates automated functional test systems for use in aerospace, military, high tech and commercial applications
-
product
NI Semiconductor Test Systems
The STS delivers the openness and flexibility of the NI PXI platform to the semiconductor production environment. For easy integration into the production test cell, the STS comes with features such as handler/prober integration, spring probe device under test interfacing, STDF data reporting, and system calibration.
-
product
AC+DC Power Sources/Amplifiers
The N4A range of AC+DC Power Sources are available with a variety of output power ratings from 6kVA up to and above 30kVA. They are the perfect solution for general power source applications as well as IEC61000 electromagnetic compatibility standards testing, offering low THD and excellent reliability.
-
product
Color Matching Booth
GSM Round Cutter is used to test material grams per square meter. It would cut sample to 100cm2 cutter, depth max 5mm. Normally, GSM cutter is suitable to cut textile fabric, leather, paper and etc. It has four double-sided blades, and the blade is evenly distributed in four equal parts. The blade can be replaced. GSM Testing is essential for some tests like Matindale abraison test meet standard ISO20344.
-
product
Scienlab Regenerative DC Emulator
SL1800A Series
Keysight's SL1800A Scienlab Regenerative DC Emulator - High-Power Series enables users to emulate the large batteries in electric vehicles. The bidirectional power flow allows emulation of both power sourcing applications, such as traction inverter test, as well as power-absorbing (sinking) applications, such as EV charging. Being regenerative, the power absorbed is delivered back to the grid, saving on energy and cooling costs. The SL1800A Series is fully integrated with the SL1040A Scienlab Charging Discovery System. The SL1093A Scienlab Charging Discover Software fully automates DC charging applications to many different test standards. With bi-directionality, integrated DC voltage and current controllers, high dynamics, and its regenerative energy feedback capacity, the Scienlab Dynamic DC Emulator provides an all-in-one system for efficient and effective testing of the power electronic components in electric vehicles (EV) and electric vehicle supply equipment (EVSE).
-
product
Synthesizers
A low phase noise frequency synthesizer module designed and manufactured for standard test instrumentation, communication, and Radar systems as a local oscillator.
-
product
Dielectric Test Fixture
16451B
The 16451B is used to evaluate the dielectric constant of solid dielectric materials accurately, and complies with ASTM D150. The 16451B employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixture.
-
product
Small Drop Test System
KRD41 series
KRD41 series small drop tester is suitable for free-fall test of small consumer electronics and components such as mobile phones, walkie-talkies, electronic dictionaries, CD / MD / MP3 and so on, applicable standards JISC 0044 and IEC 60068-2-32. Through standard tests on electronic products (surface drop, corner drop, edge drop, etc.) and collecting data, it simulates the vertical drop impact of electronic products during transportation and handling. It provides a basis for the design of the product's buffer and vibration damping and the selection of structural materials.
-
product
Component Test Systems
These products include test peripherals used with test systems, such as interfaces that connect semiconductor devices with test systems, and handlers that transport semiconductors to the test system. System-level test equipment and software are also included in this category.
-
product
SSG Series Strain Gauge Extensometers
Shimadzu’s SSG series of strain gauge extensometers are compliant with ISO, JIS, and ASTM tensile test standards, including those for plastics and metallic materials These lightweight, precision extensometers feature a wide elongation measurement range, while retaining the flexibility to measure using small gauge lengths, and support both rod and flat plate shaped specimens. Consisting of an elongation sensor and amplifier, this extensometer is suitable for use with metals and hard plastic materials, and is fastened securely to specimens with screws. Calibration using an extensometer calibrator allows the extensometer to meet JIS and ISO Class 0.5 and ASTM Class C standards for higher accuracy.
-
product
Environmental Chamber
Wewon Environmental Chambers Co, Ltd.
The environmental chamber for conditioning of samples prior to testing, It also can be used for a variety of materials of high – low temperature alternating test. The test for temperature, humidity, time can be programmed. Provides conditions of temperature from -70 degree to +180 degree and of humidity form 10% to 98%.environmental chamber ● The ideal simulation environmental chamber for all heat and cold testing between -70 ºC and 180 ºC temperature range.● Well suited for reliability testing based on current test standard in the temperature range of -70 °C to 180 °C & 10% to 98% RH.● This design SUS environmental chamber meet all requirements for extreme testing and low temperature alternating climate profiles from -70 °C -180 °C with humidity
-
product
NFC Conformance Test System
T3111S
The T3111S RIDER NFC Conformance Test System is the Keysight solution for RF Analog and Digital Protocol testing of NFC, EMV and ISO devices. The Test System is based on the Keysight T1141A NFC Test Set and it is complemented by the Keysight's or FIME's robots for accurate and repeatability RF testing. Selected 3rd party positioning robots can also be supported.
-
product
EOL RF Functional Test
AS652
With this RF test platform, integrable according to the specific needs of the product, we cover a very wide range of test needs with manual feeding.Ergonomics have been fully observed in the design, including the option of servo adjustment of the working height according to the operator.
-
product
Insulation Resistance Tester
UDH-50-1-T
UDEYRAJ ELECTRICALS PRIVATE LIMITED
utomatic-microcontroller operated• Standard test voltages-0.5kV, 1kV, 2.5kV, 5kV • Resistance range to 1TΩ • Continuous digital display on LCM• Test modes: Insulation resistance,PI (Polarization Index)AR (Dielectric Absorption Ratio)(PI and AR automatically calculated)
-
product
Functional Test
UTS
The UTS functional test system is perfect for electronics manufacturing operations that have a mix of products where operators load and unload devices under test (DUT) and routinely change out fixtures for each type of DUT.
-
product
FPD Tester Model
27014
Chroma 27014 Flat Panel Display Tester is a complete testing solution that meets the Liquid Crystal Module testing requirements of production line. With integrated video generator, multi-channel precision power supply and process control unit, the system allows a complete test of signal, pattern and electrical parameters of LCM through a PC or remote control box.
-
product
Scienlab Battery Test System – Pack Level, 110 KW Compact Version
SL1710A
Compact solution for testing Battery Packs with output power up to 110 kW and voltage range up to 1500 V
-
product
Corrosion Testing
The salt spray test is a standardized test method used to check corrosion resistance of coated samples. Coatings provide corrosion resistance to metallic parts. Since coatings can provide a high corrosion resistance through the intended life of the part in use, it is necessary to check corrosion resistance by other means. Salt spray test is an accelerated corrosion test that produces a corrosive attack to the coated samples in order to predict its suitability in use as a protective finish.
-
product
ESD - Simulator
SESD 230
The test generator SESD 216 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods
-
product
Cable Tester
FST-500 High Voltage Cable Tester is a modular and customizable cable tester that can be easily adapted to various cable test or cable harness test applications. The electronics is based on Finero’s rugged industrial grade FST range of standard test equipment. All set and measured values are shown on alphanumeric display, additionally there is an analog panel meter for output voltage. Other cable paramerter like L, C and R can also be tested by using optional test and measurement equipment. The tester can be ordered with a build in PC and it can be used in conjunction with Finero’s Quality Control software.
