-
product
PCI Express FMC Carrier
RFM-BSC5GT7H1
Sundance Multiprocessor Technology Ltd.
The RFM-BSC5GT7H1 is a PCI Express short sized FMC carrier board with Cyclon V FPGA (Altera), which is designed mostly for low cost, high-performance data acquisition.
-
product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 8 Channel
50-200-008
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
product
Beam Directional Power Supply Battery 40 to 120 kV
CP120B
This ultra-light, compact and battery operated constant potential portable X-Ray generator is the perfect tool for specific NDT applications that require repetitive short exposures. Its versatility also makes it the ideal piece of equipment for security applications. In fact, in combination with the FLATSCAN15, the FLATSCAN30 and other digital X-Ray detectors, the CP120B will – thanks to its small focal spot and constant potential X-Ray output – enhance image quality and definitely contribute to a reduced exposure time.
-
product
Breakout Box
T1000-62HD
Our most expansive breakout box, using dual High Density 62 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 124 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity.
-
product
EpiStride SiC CVD System
Veeco’s latest technology for the compound semiconductor market enables high-performance chemical vapor deposition of Silicon Carbide for both 6 and 8-inch wafer production. The platform enables a return to production in under 5 hours after routine cleaning maintenance. The EpiStride system’s high uptimes, short cycle times and overall stable performance lead to the lowest cost of ownership per wafer compared to competitive systems.
-
product
Heavy Duty Ranger Mutt
TT9102
Commercial trailer light and electric brakes tester that reduces guesswork and saves time by powering each trailer electrical circuit in 7-way round pin arrangements. Allows for proper verification of wiring configuration, ground integrity, short circuit and overload conditions, along with electric brake operation and turn signal simulation.
-
product
In-Circuit Test (ICT)
Analog components (resistance, capacitance, inductance, diodes, transistors, etc.) as well as complex digital components can be tested in the ICT. Compared to other test methods (e.g. flying probe), the in-circuit test enables very short test times (= high assembly throughput) combined with a very high test coverage.
-
product
PXI BRIC4 FIBO Matrix Dual 31x4 2pin brkout
40-592A-011
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
Voltage Stabilizer
MS 7643
VSTAB is a voltage stabilizer, regulates the incoming supply +28V voltage into the required +15V. The electrical specifications meets MIL704 standard. Over load and short circuit protections are provided. Voltage stabilizer Module is a part of shipborne unit and it is meant for ensuring the power supply of the devices of this unit when fed from DC mains with nominal voltage of 28 V and variations of voltages from minimum 16V to maximum 32 V. The power consumption is 45 watts. The module is subjected to Qualification Tests as per MIL-STD-810G.
-
product
Automotive Production Board Test
Teradyne's TestStation platform enables manufacturers to easily react to rapidly changing product requirements. From volume, mix and test complexity - there is a TestStation configuration to meet your production requirements at the highest fault coverage and yield rate. configurable from a range of a few test points for basic shorts detection up to more than 15,000 test points for more complex PCBAs.
-
product
16 Discrete/Switch I/O Channels (±80 V, 625 mA/Ch.)
DT2
The DT2 module features 16 independent, isolated, programmable channels that can be used for input voltage measurements (±80 V), or as a bi-directional current switch (up to 500 mA per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection.
-
product
Thermal Desorption
Scientific Instrument Services, Inc.
The SIS Short Path Thermal Desorption units sit directly on top of a GC injection port to provide for the direct desorption of both volatile and semi-volatile samples into the GC injection port and column. Due to the "short path" of sample flow, these new systems overcome the shortcomings of previous desorption systems by eliminating transfer lines, which are easily contaminated by samples, and by providing for the optimum delivery of samples to the GC injector via the shortest path possible--the direct, syringe-like injection into the GC.
-
product
Point on Wave Synchronous Test Sequencer
The Portable Point on Wave Synchronous Test Sequencer is India’s only system that helps in time synchronizing the control signals during short circuit tests performed on medium and high voltage switchgear and control gear.
-
product
Insulation & Multifunction Tester (LCD Display)
1155 TMF
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
product
Bench Power Supply, Single, Adjustable, Fixed, 3 Output, 0 V, 30 V, 0 A, 3 A
72-6628
The 72-6628 is a Triple Bench Power Supply with adjustable current control and galvanized steel case. The DC regulated power supply is a completely solid state, compact, well regulated, constant voltage power supply suitable for service field, hobby, laboratory and testing use. It provides three different voltages output for different. Overload and short-circuit protection, prevent the unit from overload and short circuit. When the unit is under the condition of overload or short circuit, the output current will be limited. Independent 5V, 12V easy snap-on output terminals to make it easy to use for TTL and CMOS circuit testing. The grounding of the output terminals is independent that the output can be connected in series to make a higher output voltage.
-
product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
The 40-205-008 (PXI) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
Protection Relays
Electrical protection relays for high voltage & high current protection offer protection in traction equipment as well as railway infastructure. Protection relays are used for applications like catenary voltage, short circuit, overload and ground fault detection in traction power electronics or railway substations.
-
product
LVDT Signal Conditioner
NTC-6000
Quick and easy setup with front panel push buttons and LED indicatorsSelectable excitation frequency, analog outputs and bandwidthAutomatic excitation synchronization for multiple unit systemsSelf-diagnostics for LVDT failure, disconnect, or short circuitDigital communications via RS-485 2-wire multi-drop busHot swapability — setup can be saved and reloaded via RS-485 portCybersecurity lockout and tamper detectWorks with nearly any AC LVDT, RVDT, or LVRT half bridge
-
product
PXI Load Resistor Module 10 Ohm to 2.56k
40-292-012
A simple solution for applications requiring a programmable load resistor with up to 15W power handling. It is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors.
-
product
Digital Automated Fiber & Ferrule Interferometer For Single Fiber Connectors
DAFFI SF
The latest interferometer from Data-Pixel is a cost effective solution for high volumes production, without compromising on accuracy or performance. Based on our extensive interferometer manufacturing experience we designed the DAFFI SF to be robust, fast and accurate in order to meet all manufacturing or laboratory environments. With the Blink software platform, DAFFI is able to measure the end face geometry on single fiber connectors in a very short time. The Daffi interferometer accessories (flange and adapters) are fully compatible with the Daisi range, allowing the user to limit the costs of the 3D geometry measurement units.
-
product
Hipot Tester
NX Hipot+
50 to 1500VDC Hipot Testing, 50 to 1000VAC (optional), Expandable to 1024 test points, 5Mohm to 1Gohm Insulation Resistance, Simple 4-button user interface, Tests for continuity and shorts, Tests a variety of components, Precision resistance measurements, Continuous high speed scanning for real time complete status information of harness assembly progress, Keyed security access and control, Built for rough industrial environments, 2 serial ports for connection to printers and scanners, Standalone operation, Uses a high capacity memory card, Available from 64 to 1024 test points, Networkable
-
product
4-in-1 OSLT Calibration Kit, DC to 26.5 GHz, Type-3.5 mm (f) 50 Ohm
CK521A
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
PXI RTD Simulator Module, 8 Channel, PT100
40-263-401
The 40-263-401 is an 8-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
product
PXI 10W Programmable Resistor Module, 1-Channel, 1Ω to 122Ω
40-253-112
The 40-253-112 is a programmable resistor module with 1 channel which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
Special Products
Whether your need is waveguide subsystem or custom assembly or special products such as flanges, shims, short plates, offset shorts of calibration kits, we are happy to help.
-
product
High Current SMU Family 2000 A
AXC76xx
Generate very short, fully regulated current pulses from 2 ms to DC with up to 2000 A. Carry out measurements directly on the DUT with the integrated CMU and VMU.
-
product
Total Stations
Zipp02 Series
With vertical compensation and 2” accuracy the Zipp02 provides you with the precision required for your most demanding jobs at an affordable price without adding complexity. The Zipp02 is the tool of your choice when it comes to checking angles, alignments, grade work and short range leveling.
-
product
Stand-alone Type Chemical Concentration Monitor
CS-100 Series
The optimal model to suit chemicals from among over 100 different applications can be chosen. Measurements of the concentration of each component can be taken in real-time, providing notifications using alarms to signal the timing of chemical exchange and automatic replenishment. Short measurement cycles to faithfully track concentration changes can be achieved.
-
product
Switch Mode Power Supplies-Air Cooled
The MS-Series features constant voltage and current control with easy, quick installation and maintenance. Modular versions easily increase the output by means of series or parallel connection. All models have DC short circuit protection. With forced air-cooled models, the cooling air quantity is controlled in relation to the load reducing contamination and noise levels.
-
product
CT Admittance Tester
505B
Red Phase Instruments Australia Pty Ltd.
Field testing kWh meters is easy, field testing CTs when live is much more difficult. Our admittance tester can test CTs live with 50Hz or 60Hz current in the metering circuit. This technique does not confirm the accuracy of a CT but it will detect faults that give metering errors, such as shorted turns, metering circuits shorted to ground and tampering of CTs. CT faults can cause large revenue losses. Admittance testing only adds 10 minutes to a routine polyphase meter test, giving cheap insurance.
