-
Product
RF Power Monitors
-
Bird's RF Power Monitor family includes a range of products that not only measure power and VSWR but also provide hard contact alarms to protect your system in the event of a system failure – the IP-enabled, BPME is even capable of emailing a failure notification.
-
Product
High Load Strength Tester
HLST1000Z
-
This tester measures the tensile or compressive strength of various samples
-
Product
Standard Helmholtz Coils
-
Helmholtz Coils are ideal for the measurement of Rare Earth (Samarium Cobalt, Neodymium) and Hard Ferrite permanent magnet materials (materials which exhibit a relative straight line demagnetization). Our standard Helmholtz Coils are for use with fluxmeters. The Helmholtz Coil measures the magnet sample as a single magnetic moment provided that the longest dimension of the magnet sample is less than one-third (1/3) the diameter of the coil system. By definition, the magnetic moment per unit volume is the intrinsic magnetization of the sample. With our calibrated Helmholtz Coil and Integrated Fluxmeter – and given the volume of the permanent magnet sample – the intrinsic open circuit operating B (Bdi) can be measured.
-
Product
RF Accessories
-
NSI-MI's RF accessories that simplify and reduce the cost of RF transmit and receive systems.
-
Product
Field Evaluation And Special Inspections
-
Nemko offers Field Evaluation and Special Inspection Services in the US and Canada as a fast and economical alternative to traditional product safety certification.
-
Product
RF Connectors
AMC4 Connectors
-
The AMC4 (Amphenol Micro Coaxial, 4th Generation) connector series is a low profile (0.6 mm height off the board) series with an extremely small board footprint (2 mm x 2 mm).
-
Product
RF Solutions for Space
-
Our proven design and manufacturing processes yield high-performance, radiation-hardened, high-reliability RF devices that are designed to withstand the harsh conditions of space.
-
Product
Laser- Field of View Measuing System
SIMES
-
F. W. Breithaupt & Sohn GmbH & Co.KG
*For checking vehicles in order to meet standards concerning field of view*Developed in cooperation withTÜV Rheinland
-
Product
Damped Oscillatory Magnetic Field Immunity Tester
DOMF61000-10
-
DOMF61000-10 damped oscillatory magnetic field immunity test system included damped oscillating wave generator and single ring coil, it’s designed for to do damping oscillation magnetic field immunity test and fully meet IEC 61000-4-10, EN61000-4-10 and GB/T 17626.10 standards requirement.
-
Product
RF Impedance Transformers
-
Are designed and optimized to best deliver power into an impedance of 50 Ohms.
-
Product
- Optical / RF Converter
OPT 80
-
Calibrated measurement of the optical power of satellite and terrestrial TV signals distributed in optical fiber Calculation of optical signal losses on distribution Measurement of digital parameters (BER - MER - NM etc.) of optical signals converted into RF Visualization of optical carriers in RF Field Metric Spectrum Analyzer Power Meter Optical Field Meter Display Optical RF Power Supply Line Link Meter (LNB power supply ) Optical LNB power supply 13V 500mA with short circuit and overload managementAcquisition of optical measurements using the field meter Data Logger Option: certification of the OPT80 calibration and optical power measurements
-
Product
Analytical Reference Materials & Standards
-
Agilent, now with former Ultra Scientific, offers a comprehensive portfolio of analytical standards, reference materials and certified reference materials for environmental, food safety, elemental analysis, instrument calibration, tuning mixes, and more.Reference materials and certified reference materials are substances that are tested to be homogenous and have fixed values of its concentrations. These standards are a critical component of your application workflow - from sample prep, instruments, columns, supplies, and services. The success of your analysis depends upon the quality of your reference material. All Agilent standard reference materials have been manufactured to the highest quality in an ISO 9001, ISO 17025 and 17034 accredited facilities to ensure the accuracy of your analyses.If you need a custom reference material, partner with us to design and develop a custom standard to your specifications.
-
Product
RF Safety Monitoring
FieldSENSE 60
-
The fieldSENSE 60 personal RF monitor has a proven track record of durability that works as hard as you do. fieldSENSE 60 is specifically designed with the RF climber in mind.
-
Product
Vector Field and Multi-Axis Systems
-
Cryogenic vector magnet systems allow precise alignment of the magnetic field to an exact direction in a measurement sample. The system provides the capability of orienting the magnetic field to any vector direction. This is suitable for experiments where samples cannot be moved easily.
-
Product
VXI Rubidium/GPS Frequency Standard
3352A Series
-
The Racal Instruments™ 3352A Rubidium frequency standard module and the 3352A-GPS, its GPS-disciplined companion, set a new standard for high density functionality in a single width VXI module. Using ANSI Standard M-Module building blocks, the 3352A series integrates the functions of a Rubidium oscillator and clock distribution together with an optional trigger distribution module and an optional digital I/O (DIO) module.
-
Product
Digital ESD Field Meter
FM-1126
-
Now with an ionizer probe attachmentIndicates voltage and polarityDigital display is updated every three secondsNon-contactPower on/hold and zero buttonsEasy to read 3.5" LCD displayRange: 1-20,000v1" spacer bar9v batteryLeather case includedProduct conforms to the ESD S.20.20 spec standardsChecks for class zero conformance
-
Product
RF Deluxe
ICAP/4Rx
-
ICAP/4Rx RF Deluxe is an extended version of ICAP/4Rx, including simulation capability for RF frequency design. This powerful system includes everything you need to design and verify all types of board, engineering system and IC-level design. Of course, ICAP/4Rx Power Deluxe includes Intusoft's time-tested "IsSpice4" analog and mixed-signal simulation kernel, featuring more enhancement than any SPICE kernel on the market for convergence, accuracy, speed and interactive capability.
-
Product
RF Connectors
HD-BNC Connectors
-
The HD-BNC product line delivers both true 50 and 75 ohm performance in a footprint 4 times smaller than traditional BNC connectors. Using the same cable prep and termination specifications of legacy broadcast connectors makes adopting HD-BNC seamless.
-
Product
GPS Frequency Standards
-
Precision Test Systems manufacturers' a full range of GPS and GNSS frequency standards that are disciplined to most of the worlds satellite systems.
-
Product
Zero Field Cavity
-
Zero field cavities generate a zero magnetic field in an air gap. They are mainly used to calibrate hall probes for their zero scale value of output for the magnetic field strength H or the magnetic flux density B they measure. For example Gaussmeters can be calibrated by using Zero Field Cavity.
-
Product
"Standard" RF Low Pass Filters
-
Coaxial Dynamics "Standard" line of RF Low Pass Filters offers several models to choose from at CW power ratings of 100 watts and 200 watts. These filters cover operating frequencies from 88 MHz to 400 MHz with less than 0.5 dB insertion loss and attenuation levels of 40, 50 and 60 dB.
-
Product
Peel Strength Testers
-
Peel Strength Tester can be used for peeling, stripping and other performance tests of adhesives, adhesive tapes, pressure sensitive tapes, medical adhesive bandages, protection films, release paper, laminated films, leather, woven bags and paper.
-
Product
RF Filters
-
RF Filters block unwanted frequencies when testing electronic devices for emissions during EMC testing. They attenuate unwanted frequencies and allow the desired signals through. The RF filters isolate the device under test from external RF noise, this increases the reliability and accuracy of the EMC testing by preventing out-of-band noise and harmonics.
-
Product
RF Filters
-
Amphenol Procom has 40 years of experience in developing and producing high quality RF Low- and high-power Filters for professional radio systems, widely used in the Public Safety and Mission Critical radio TETRA networks in Europe. The comprehensive portfolio of Filter products from Amphenol Procom are designed by experienced engineers, and highly used in the HF-, VHF- and UHF radio frequency range.
-
Product
Standard Digitizer
725S Family
-
The 725S family is a digitizer capable of recording waveforms along with performing advanced algorithms for online digital pulse processing (DPP). Utilizing DPP Firmware, users can acquire quantitative physical parameters (Integrated Charge, Pulse Shape Discrimination with very fine time resolution, Pulse Height Analysis) as well as read out waveforms with automatic pulse identification and baseline suppression on channel basis (Zero-Length Encoding and Dynamic Acquisition Window). The wide range of DPP algorithms supported by the 725S make it a “must-have” for any type of nuclear physics application.
-
Product
RF Calibration Accessories
-
Employing good connector practice when using an RF calibrator not only avoids measurement errors and minimizes connector repeatability uncertainties but also reduces risk of damage to connectors and equipment. The 96000CONN and 9600CONN connector kits include a range of adapters and torque wrenches intended for use with the 96000 Series RF Reference Sources (9600CONN for the 96040A and 96000CONN for the 96270).The 9600CONN connector kit includes one each of 50 Ω and 75 N-Type male-female adapter for use with the 96000 Series levelling head as a “connector saver” or “sacrificial connector” to avoid risk of damage when making connections to UUT/DUT instruments.
-
Product
Standard CT
6300A
-
The Model 2509 Instrument Current Transformer is a 6300 A ampere CT designed for precision measurement of AC current or for Instrument Current Transformer calibration applications. The CT can be installed on a bus bar or it can be used with a primary conductor consisting of number of turns. The 6300 CT is designed with a tapped primary & a tapped secondary winding, thus providing a large number of ratios over a range of 5 to 6300 amperes.
-
Product
RF Shielded Box
LTL D7001
-
LTL D7001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL D7001 RF shielded test enclosure can comfortably house the intermediate device on test.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
IEC60065 Dielectric Strength Tester
PG-K02
-
Shenzhen Chuangxin Instruments Co., Ltd.
The IEC60065 Dielectric Strength Tester is mainly used for testing thin-layer insulation material electric strength.and IEC60065 Dielectric Strength Tester is with ISO17025 Calibration Certificate
-
Product
Field Strength Meter
FIM-71 VHF
-
The Model FIM-71 is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-71 is suitable for practically all types of RF emission measurements in the 45 MHz to 225 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and a meter dynamic range of either 20 dB or 60 dB. A dc analog output voltage, proportional to the meter indication, is provided for driving a chart recorder. A leveled output from the calibrating oscillator is available for measuring cable insertion loss, filter response, amplifier gain, and other signal ratio measurements. The 4-1/2 inch, taut band, mirrored scale meter is calibrated in volts and dB for precise measurements in field or laboratory environments.
