-
Product
PXI 32 Channel I/O, Low Side Driver
40-413-002
-
A 32 channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only, a low side only (shown here)and a combined high and low side each capable of driving 2A loads. Each output is fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side voltage driving the high side voltage source is supplied from an external voltage source, permitting the module to drive high capacity loads without impacting the PXI chassis power supply.
-
Product
Dual Channel Clock Driver Card
PI-41400
-
The PI-41400 is a dual channel Clock Driver card capable of operating up to 190 MHz into a 50-ohm load and up to 80 MHz at an amplitude of 8 volts into a 1-megohm load. Into a high impedance load the output voltage range is from a –3 volts to 8 volts with the output pulse amplitude ranging from 0.5 V to 9 V. When driving a 50 load the voltage range is –1.5 volts to 4.5 volts with the output pulse amplitude ranging from 0.25 V to 4.5 V. The rise and fall times of the output pulse are variable from 1.2 ns to 9 ns into a 50-ohm load and <5 ns to 9 ns into a HiZ load. The output pulse amplitude and the load being driven determine the range of variability. The driver output can be set for tri-state operation and the output polarity can be set for ‘Normal’ or ‘Inverted’ operation through software.
-
Product
PCI-8517, 2-Port FlexRay Interface Device
780685-02
-
2-Port FlexRay Interface Device—The PCI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PCI‑8517 contains two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
Product
Bridge Devices
USB
-
*Royalty free Virtual Com Port (VCP) drivers*Simple GUI based Xpress configurator for configuring, programming and customizing applications*No USB expertise required*Seamless compatibility with most operating systems*UART, SPI, I2C/SMBus and I2S interface options available*Fastest way to add USB Turn key, no firmware development needed
-
Product
Laser Diode Driver
S-101
-
LD Driver slot module of FOTS system is an efficient module that is user centered, which can drive various kinds of laser diode for the use of optical signal transmission or light source. The module has a built in LD socket, in which LD of 14 pin butterfly type is installed, which makes it possible for the user to change the LD he or she wants to drive when needed. It is leaded to get rid of the inefficiency of expense, at which various types of expensive united source module needed are purchased. By operating monitoring PD and high-performance processor that are installed inside the module, the output power and temperature of LD can be driven accurately and stably. The laser diodes can be modulated internally in square, sinusoidal, and triangular waves and its output power and temperature can also be maintained the level set by the user. In order to realize the various functions, the efficient and multi-functioned control programs with high speed processor, LCD monitor or GUI for remote control are available.
-
Product
Private Cloud Device Hosting Management Solution
ZAPFARM
-
ZAPFARM is a private cloud device hosting management solution that allows organizations to manage mobile devices and conventional workstations under test to offer their testing and development teams to manage applications under test and test cycles for Cross-Platform/cross-environment applications development and testing remotely.
-
Product
Advanced Driver Assistance Systems (ADAS) Testing
-
Advanced Driver Assistance Systems (ADAS) TestingAll modern vehicles are now being equipped with Advanced Driver Assistance Systems (ADAS). The development of such systems requires complex testing, including the ability to control and calculate relative positions between multiple vehicles and objects in real-time. We provide an effective solution for ADAS testing with highly accurate GPS positioning systems to measure relative positions and velocity between multiple vehicles and objects.
-
Product
Device Testing
-
The BTL Working Group (BTL-WG) has developed a test package which contains a set of testing procedures. These can be acquired and used by manufacturers to pre-test their products for BACnet compliance before they send their products to an RBTO (Recognized BACnet Testing Organization) for BTL Testing. The BTL Test Package is available on the test documentation page.
-
Product
Powered Device Analyzer for 802.3at & 802.3bt
-
The One-Box solution for 802.3 Ethernet Powered Device testing and verification including flexible emulation of PSE behaviors, scalable feature configurations, and plug’n play testing using a Windows PC.
-
Product
Recorder Carrier Device
RCD
-
The RCD is a carrier signal demodulator for SCADA and Fault Data Recording. the RCD demodulates the carrier to indicate the presence of a relative level of a singal
-
Product
SSD - Solid State Storage Devices
-
LinkedHope Intelligent Technologies Co.,Ltd.
LinkedHope Intelligent Technologies SSD Products
-
Product
Specialized Systems and Devices
-
Is the most comprehensive earthquake monitoring solution for the power generation industry in general and nuclear plants in particular – including seismic-event data recording, analysis and notification via hardware alarms and reports – all in one system, delivering confidence in continuing safe operations after an event.
-
Product
Photonic Device Testing
-
ficonTEC’s series of photonic device testing machines is focused on automated electrical, optical or mixed-signal electro-optical characterization (test-&-qualify) of chips and dies, opto-electronic assembles and integrated devices. Capability includes PIC design validation and device verification.
-
Product
Electricity Metering Device
Mk10E
-
Built on the advanced Atlas metering platform, the Mk10E has a Class 0.5S measurement engine with many enhancements including smart grid solutions, high data storage, data processing, UPS configuration and enhanced communications capabilities.
-
Product
4G, 3G and 2G Device Testing
-
Wireless network emulators enable the entire mobile device ecosystem to accelerate delivery of 5G new radio (NR) products.
-
Product
Ethernet Multifunction DAQ Device
T4
-
USB or Ethernet multifunction DAQ device with up to 12 analog inputs or 16 digital I/O, 2 analog outputs (10-bit), and multiple digital counters/timers. For more information on the T4 take a look at the T4 product announcement news post.
-
Product
Portable Gas Measurement Devices
-
Teledyne Gas & Flame Detection
Looking for portable gas leak detectors to protect your staff? Teledyne Gas and Flame Detection measuring devices meet all your requirements.
-
Product
Free Modbus Device Tester Software
-
Global Multimedia Private Ltd.
This software was developed to test Information Displays made by Global Multimedia for modbus protocol compliance. It can be used to test your firmware on a serial device for Modbus RTU conformance.
-
Product
Laser Diode Drivers
-
Renesas offers a portfolio of laser diode driver (LDD) ICs for DVD/CD/Blue-ray optical drive and laser projection applications.
-
Product
PXI/PXIe High-Speed Multi-Measurement Device
PXM(e)7820
-
The PXM Multi-Measurement Devices combine the functionalities of a digitizer, a multimeter, a timer/counter and a highly flexible trigger matrix in a PXI or PXIe device.
-
Product
Industrial 4-20mA Driver
-
Analog Devices portfolio of leading industrial d/a converters and drivers addresses the challenges of enhancing system accuracy, reliability, and overall functionality while reducing form factor and power dissipation. The products provide a range of programmable output ranges from standard 4–20 mA for current loop communication to ±10 V for actuator control. They simplify industrial system design by offering considerable control functionality and advanced on-chip diagnostics to maximize system up time. ADI industrial converters also eliminate the need for costly calibration routines needed by some traditional discrete architectures.
-
Product
PCI Data Acquisition Boards
-
Ultraview''s PCI data acquisition add-in cards are complete data acquisition (A/D) and control (D/A) systems on a single PCI Bus card. Ranging in speed from dual 14 and 12-bit 1-25MSPS boards up to 1500MSPS 8-bit boards with 8GB/16GB of on-board RAM. All cards come with graphical waveform viewers, example user programs (source code included) and device drivers for Linux or Solaris, allowing users to quickly prototype and develop their applications.
-
Product
Analog Meters & Built-In Devices
-
PeakTech Prüf- und Messtechnik GmbH
Is able to display currents in the range 0 - 100 µA DC with high precision due to its scale measuring range. This inexpensive device is designed for use as a desk device / tabletop device, furthermore this analog device does not require a power supply, which means that it can be used permanently and economically. The respective measured values can easily be read by the student on the large analog mirror scale.
-
Product
Digital Multimeter Device
-
Digital Multimeters measure voltage, resistance, current, capacitance, inductance, and temperature. Some models also have an isolated digitizer mode. Use these products to test consumer electronics, fuel cells, aerospace production, and more.
-
Product
USRP Software Defined Radio Reconfigurable Device
-
The USRP Software Defined Radio Reconfigurable Device is built on the LabVIEW reconfigurable I/O (RIO) and universal software radio peripheral (USRP) architectures. It includes a powerful FPGA for advanced DSP that you can program with the LabVIEW FPGA Module. The device includes 2x2 MIMO transceivers or four-channel superheterodyne receivers, supporting center frequencies from 10 MHz to 6 GHz, with up to 160 MHz of instantaneous bandwidth. The USRP Software Defined Radio Reconfigurable Device also optionally includes a GPS‐disciplined oven-controlled crystal oscillator (GPSDO), which provides greater frequency accuracy than temperature- compensated crystal oscillators. Prototyping applications include LTE and 802.11 prototyping, spectrum monitoring, signals intelligence, military communications, radar, direction finding, and wireless research.
-
Product
Control Driver
-
Citizen Chiba Precision Co., Ltd.
High functioning and compact driver for motors and actuators
-
Product
Electrostatic Potential Monitoring Device
-
electrostatic potential monitoring device that has an interface for connecting our potential sensors EMS-01 / EMS-01A / KS-2100 and measures static electricity in real time. It is possible to monitor static electricity with simple The compatible potential sensor EMS-01 / EMS . With SD card support, measurement data and alarm history can be collected with a time stamp. Operation using the touch panel display and screen display, and to notify and manage the measurement status with multiple control outputs. ...-01A Has Passed The Intrinsically Safe Explosion-Proof Structure Certification In Combination With The Safety Cage KS-301A, And Can Be Used In A Dangerous Atmosphere.
-
Product
Handheld Testing Device
GPON Tracer
-
GPON Tracer is the ideal tool for both telecom operators' field engineers and customer support teams of OLT and ONT/ONU manufacturers. Featuring a compact handheld device with a user-friendly touch screen interface, the GPON Tracer provides a rich variety of real-time indications in simple graphical and textual formats, giving accurate indications of network and service issues and their root causes. Moreover, GPON Tracer reduces repair charges by preventing unnecessary replacements of properly working equipment.
-
Product
High Resistance Neutral Grounding Devices
-
HRG systems limit the fault current by placing high resistance between neutral point of transformer (or generator) and ground. As it is not possible to locate the fault point in delta connected systems, an artificial neutral point is created and delta connected system can be grounded. This allows a fault current of a few amperes thus locating the fault point gets easy. When the neutral point is grounded thru high resistance, both continuity of operation is provided during fault condition and sufficient current (typically between 2 A and 10 A) flow is provided for ease of locating the fault point.
-
Product
USB-TC01, 1-Channel Temperature Input Device
781314-01
-
The USB‑TC01 is a thermocouple measurement device featuring InstantDAQ technology. InstantDAQ technology includes built-in software for viewing and logging data that automatically loads when you plug in the device, so you can instantly take … temperature measurements with your PC. You can connect the USB‑TC01 to any USB port to use your PC as a display and monitor data in real time. The USB‑TC01 is compatible with J, K, R, S, T, N, E, and B thermocouples.
