-
product
Handheld Xrf Analyzer, Metal Analyzer, Rohs Analyzer
SG-2000S
Handheld XRF Analyzer, Metal analyzer, ROSH analyzerThis is a portable analyzer specially designed for production site and field environment, which is featured with small size, light weight, easy operation and super long standby, etc. It's widely applied in such fields as alloy steel, geological surveying, mining and metallurgy, metal recycling, and precious metal testing, and can also be applied in quantitative analysis of all elements from Magnesium (Mg) to Uranium (U).
-
product
Metal InspectionSystems
Metal surfaces must undergo a reliable inspection, because defects impair the functions of steel tubes or medical engineering products. Relying to the often appearing strong structures of such surfaces, special robust vision techniques are needed to make, for example, geometric measurements. Our systems are prepared to provide a fully automated, 100 % inspection rate in a rough industrial environment.
-
product
Cable 100-Pin Micro-D Male To Unterminated, Cut Ends, 2m 2-56 UNC Screwlocks, Metal Shell
A100SMR-C-9B200
100-Pin Micro-D Male to Unterminated Cable Assembly With Cut Ends, 2m Long With 2-56 UNC Screwlocks and Metal Backshell. Suitable for use with Pickering BRIC Modules.
-
product
Wavefront Modeling And Simulation
The CAST-CRPA Simulation Systems provide a precise, coherent, and repeatable GNSS RF signal “wavefront”, that is a perfect solution for testing phased array, or “CRPA” antenna systems, in a laboratory environment. The system generates a complete set of RF signals for each antenna element, which are referenced to the phase center of the antenna manifold. In addition, the CAST system allows users to add interference and IMU signals that can also stimulate EGI’s and a wide range of modernized navigation devices.
-
product
Metal Wire Torsion Testing Machine
WTT Series
Jinan Testing Equipment IE Corporation
WTT series metal wire torsion tester is mainly used in a metal factory to test the plasticity of metal wires and ropes under torsion condition. Surface flaws of steel wires may be shown during the testing process. The revolution is displayed on a 4- digit LED, with the max. revolution value displayed as 999.9. The revolution value is automatically held at the break of specimens. With computer & software, the Metal Wire Torsion tester can realize automatic control. The Metal Wire Torsion tester conforms to standard ASTM A938, ISO7800. The Metal Wire Torsion tester is an ideal QC tool for Quality Inspection & Control Department related to steel wire application.
-
product
Wide Measurement Range Model Of Semi-automatic 4 Point Probe Sheet Resistance/resistivity Measurement
RT-3000/RG-2000 (RG-3000)
*User programable measurement pattern & programmable measuring pattern*Tester self-test function, wide measuring range*Thickness, edge, temperature correction for silicon wafer*Film thickness conversion function from sheet resistance*2 types measuring tester (S version: Standard type, H version: High range resistivity measurement type)
-
product
Constant Potential Generator Metal Ceramic X-Ray Tube 30 to 300 kV
CP300C
The CP300C is the first panoramic x-ray generator of the CPSeries product range. Equipped with a metal-ceramic tube, the CP300C is a light (less than 30kg) and powerful generator (300 kV), able to penetrate up to 52mm of steel in 10 minutes, making it the best power-to-weight ratio in the world.The efficiency of the CP300C is also maximum thanks to its real 100% duty cycle that allows longer exposure time (> one hour).A full range of accessories is available (holding bars, tripod…) and even a 60°x40° lead diaphragm to convert the CP300C into a directional unit.
-
-
product
Model A8: All-Purpose Moisture Meter
N/A
Designed for flat, curved, smooth, or rough surfaces such as cones or beams of yarn, rolls or stacks of paper or paperboard. Covers 3" a diameter (7.6mm) and penetrates 3/4" (1.9cm). Reliable, long battery life. Includes a rechargeable battery, carrying case, and operating instructions book.
-
product
In-line Metal Mixers
Nordson EFD in-line metal mixers’ housings and elements are made primarily of stainless steel. This makes them ideal for high-pressure applications and easy to clean and reuse.
-
product
Cable 100-Pin Micro-D Male To Unterminated, Tinned Ends, 0.5m 2-56 UNC Screwlocks, Metal Shell
A100SMR-T-9B050
100-Pin Micro-D Male to Unterminated Cable Assembly With Tinned Ends, 0.5m Long With 2-56 UNC Screwlocks and Metal Backshell. Suitable for use with Pickering BRIC Modules.
-
product
Metal Alloy Low Resistance Chip Resistor
MR
*Low Resistance / TCR / Inductance*Excellent long term stability*RoHS compliant and halogen free*Lead free*High precision current sensing and voltage division
-
product
Custom & Special Models
Futek Advanced Sensor Technology, Inc.
Custom Load Cells manufactured in the US by FUTEK Advanced Sensor Technology (FUTEK), a leading manufacturer producing a huge selection of Custom Force Sensors and Custom Torque Sensors utilizing one of the most advanced technologies in the Sensor Industry: Metal foil strain gauge technology.
-
product
3D Semiconductor & MEMS Process Modeling Platform
SEMulator3D
SEMulator3D® is a powerful 3D semiconductor and MEMS process modeling platform that offers wide ranging technology development capabilities. Based on highly efficient physics-driven voxel modeling technology, SEMulator3D has a unique ability to model complete process flows. Starting from input design data, SEMulator3D follows an integrated process flow description to create the virtual equivalent of the complex 3D structures created in the fab. Because the full integrated process sequence is modeled, SEMulator3D has the ability to predict downstream ramifications of process changes that would otherwise require build-and-test cycles in the fab.
-
product
Common Metallic Pendulum Impact Testing Machine
JB-(C/D)
Jinan Testing Equipment IE Corporation
KB- (C/D) common type metallic pendulum impact testing system is the basic model for impact tester. The metallic pendulum impact tester is used to determine the impact resistance of metal materials under dynamic load and capable of doing a large number of impact tests continuously. The display method for the models is different, respectively there are analog dial display, touch screen digital display and computer display. For the later two models, it can display the impact power, impact toughness, and pendulum rotation angle. All the testing reports can be printed out. The metallic pendulum impact testing system is the essential quality control equipment for metal material manufacturers and QC departments, as well as the necessary instrument of research institutes for new material research.
-
product
Interference Modeling And Simulation
The CAST Navigation Jammers are designed to facilitate and support the testing, verification, and integration of single element Fixed Reception Pattern Antenna (FRPA) systems as well as multiple-element anti-jam antenna sub-systems such as Controlled Reception Pattern Antennas (CRPAs). These systems are an ideal solution for military and commercial laboratories where interference signal capability is required. CAST Jammer sub-systems provide precisely controlled signals for use in most types of GNSS testing applications, emulating interference conditions and threats that can occur in both urban and hostile environments.
-
product
Metal Glaze Resistor
MGR Series
*High stable performance against environmental conditions and over load voltage.*Wide resistance range
-
product
Software Module for Validating CAD Model Translations Directly in Verisurf
Verisurf Validate
Your in-house Engineering or external customer can send their native CAD file from any design platform, and with a Verisurf translator read it directly into Verisurf eliminating double-translation (the first translation out from the native CAD system, followed by a second translation into Verisurf for your CMM work). CAD options are: CATIA V5 & V6, NX, CREO, JT, & STEP AP242 with MBD. (Note that IGES, STEP, SolidWorks, Autodesk, AutoCAD and several others come included automatically with Verisurf at no extra charge.)
-
product
Current Sensing Resistors, Metal Plate Type -MS, MB
Panasonic Industrial Devices Sales Company of America
An AEC-Q200 Compliant SeriesPanasonic components specified as AEC-Q200 Compliant are consistently designed into automotive systems. However, today’s Design Engineers are specifying AEC-Q200 components to meet the high-quality standards of devices beyond automotive applications.
-
product
PC-Based Reconfigurable Inner Ship Modeling
PRISM
Textron Systems' PRISM is used to model the user’s platform under training, providing the student the ability to “see” the environment surrounding the equipment. With PRISM, users can script malfunctions, set initial conditions, supply evaluation results, and allow the equipment layout to be tailored to meet training objectives, which more closely matches a real-platform configuration. PRISM can be seamlessly combined with FORTRIS™, which provides the comprehensive physical and electromagnetic environment outside the platform, giving the user a complete end-to-end training experience.
-
-
product
Precious Metals Handheld XRF Analyzer
The DELTA Precious Metals XRF Analyzer provides fast, accurate alloy chemistry and karat classification with one nondestructive, non intrusive test. Whether importing precious metals, selling or producing jewelry, or processing scrap metal, Innov-X XRF is the ideal choice.
-
product
100 Pin Micro-D Cable, Male To Male, 0.5m 2-56 UNC Screwlocks, Metal Shell
A100SMR-100SMR-9B050
This 0.5m long male to male 100-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28 AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products. This cable assembly is suitable for use with Pickering BRIC modules that use the 100-pin Micro-D connector.
-
product
Software Module for Analyzing Measured Data to any CAD Model
Verisurf Analysis
Simplifies part inspection through the comparison of measured points, clouds, and meshes, to all CAD file formats. Check part characteristics such as position and profile quickly and easily using a variety of alignment, analysis, and reporting techniques.Analyze to CAD with imported data sets or directly from measured points, clouds, or meshes from 3D measuring devices including portable probing and scanning systems and both manual and CNC CMMs to analyze part tolerance compliance.
-
product
Cable 100-Pin Micro-D Male To Unterminated, Tinned Ends, 2m 2-56 UNC Screwlocks, Metal Shell
A100SMR-T-9B200
This 2m long male to unterminated 100-Pin SCSI Style Micro-D Cable Assembly is suited for direct connection to various products using the 100-Pin connector. It is constructed from 100-Pin twisted pair cable with varying left and right hand lays to minimise crosstalk. The Cable is colour coded to ensure easy connection. Screwlocks are provided to secure the SCSI connector to its associated product.
-
product
PathWave IC-CAP Device Modeling Platform
W7300B
The W8500BP IC-CAP Device Modeling Platform Bundle provides the basic tools you need to start modeling devices and circuits. It provides the necessary tools to:
-
product
Metal Cored PCB
Teledyne Labtech is at the forefront of complex metal-cored PCB design and manufacture. The PCB use a thin metal core <2 mm, which acts as isolation between the RF/Microwave circuit and the Analogue/Digital circuitry and creates an excellent thermal path.The major advantages are reduced size and no need for complex microwave feed-thru's. The ability to laser cut pockets allows the designer engineer to mount the high power MMIC directly on to the metal core.
-
product
Fortress Metal Detection Systems
Cantrell•Gainco is an authorized OEM partner of Fortress metal detection equipment for the meat and poultry industry in America. The Fortress brand represents the ultimate in metal detection quality and performance.
-
product
Hand Held Metal Detectors
Handheld metal detectors (also known as ‘metal detection wands’) for use in conjunction with metal detector archways or in isolation for certain applications.
-
product
Metal Box Locator
P500
Although originally designed to accurately locate valve boxes and manhole covers, the Elcometer P500 Metal Box Locator can also be used as a general metal detector.
