-
Product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 4 Channel
50-200-004
-
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
Product
5-Slot 32bit 6U CompactPCI H.110 Bus Backplanes
cBP-6105R
-
- PICMG:2.0 R3.0, 2.1 R2.0, 2.5 R1.0- Dimension (mm, WxH):120.9 x 262.05 (mm, WxH, vertical insertion view)- Segment:One- cPCI Bus:32-bit/33MHz- System Slot:Right-hand side (upper side for board's horizontal insertion)
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for VME With 4, 6 Or 8 CAN Bus Nodes
AVC825-x
-
ARINC825 (CAN bus) Test & Simulation Module for VME with 4, 6 or 8 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AVC825-x VME card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
PCIe Smart Bus Extenders
-
The PCIeEXT16HOT enables PCIe x16/x8/x4/x2/x1 boards to be rapidly tested, removed and swapped without having to reboot or power down the host system enabling rapid production testing and engineering debug. The hot insertion, current reporting, overcurrent indication and limiting and voltage margining capabilities make this board the highest performance PCIe bus extender in the industry.
-
Product
PCI Bus Carrier
APC8621A
-
This board interfaces industry-standard Industrial I/O Pack (IP) modules to a PCI bus on a PC-based computer system. The half-length card is ideal for use in smaller PC chassis.
-
Product
PCI Bus Synchro - Resolver - LVDT I/O Cards
PCI Synchro
-
Computer Conversions Corporation
Proven "Whole" Std. ConvertersOptimized Thermal ManagementExternal Synchro AMP I/O100% Transformer Isolated I/OPermits 2 wire X/Y Stators(Air)No External Parts or Power RequiredReference Powered(NAVAL) Options10-16 BIT Resolution ProgrammableVirtually Indestructible Outputs1.2 to 4.5VA High Power ModelsMix/Match Input & Output TypesSimultaneous Fine/Coarse Transmit For Multispeed Outputs
-
Product
PXI 4 Slot BRIC Module, 2 Resource Distributor, 1 Bus Matrix Inputs
40-569B-021
-
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-021 is a 4 slot module fitted with 1 Bus Matrix Inputs card and 2 Resource Distributor cards.
-
Product
PXI 8 Slot BRIC 414x8 1-Pole Dual Analog Bus (9 sub-cards)
40-560A-121-414X8-M
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Digitizer/Oscilloscopes for PCI Express Bus
-
Wuntronic Digitizer/Oscilloscopes for PCI Express Bus
-
Product
PXI 8 Slot BRIC Module, 1 Resource Distributor, 2 Bus Matrix Inputs
40-569B-112
-
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-112 is a 8 slot module fitted with 2 Bus Matrix Inputs cards and 1 Resource Distributor card.
-
Product
Functional Test System Optimized For Real-Time Digital Bus Test
Spectrum HS
-
Spectrum HS is Teradyne’s fully integrated functional test system. Optimized for real-time test of low latency buses, it’s a high-performance system delivering excellent test coverage of current and future products.
-
Product
PCIexpress Bus Extender
VITA 73
-
A PCIexpress bus extender kit permits a standard desktop PC to expand its available PCIe slots to a VITA 73 backplane. The desktop can be used as a master CPU to accelerate development.
-
Product
PXI 8 Slot BRIC 184x8 1-Pole Dual Analog Bus (4 sub-cards)
40-560A-121-184X8-M
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PCI Express® Bus to 3U PXI Express™ Chassis Expansion Kit
ACL-EXPRESS-1
-
The PCIe-to-PXIe expansion kit includes one PCIe-8560, one PXIe- 8565, and one ACL-EXPRESS cable (1 meter)
-
Product
VME Bus Analyzer / Exerciser
VME650
-
The VME650 Analyzer / Exerciser supports the latest VME bus specifications and protocols. From standard VME transfers to MBLT protocol.
-
Product
Single Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-101
-
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
PCI and PCI-X Bus Analyzer / Exerciser
PCI850
-
The PCI850 analyzer provides a multitude of functions to help analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
Power And Bus Protection Units
-
Silver Engineering Inc. offers several Bus Protection Units designed to protect the power input to a spacecraft or payload during integration and test activates. The BPU’s monitor for over/under voltage and over current and disconnects power in the event of a fault condition.
-
Product
1-port CAN Bus Data Logger
CAN-Logger100
-
The CAN-Logger100 is a high-performance smart CAN bus data logger with one CAN port that can help collect data and process on a CAN bus network easier and quicker. The powerful CPU of the CAN-Logger devices provide the accurately time-stamp for each CAN message and support storage media like SD card or SDHC type flash to save CAN messages, which helps users easily analyze and diagnose the CAN Bus network. Providing great portability, the CAN-Logger100 is powered by USB interface or M12 connectors of CAN bus interface. The CAN-Logger100 device uses the standard USB HID driver of the Windows system.
-
Product
RTSI Bus Cables for 5 PCI or AT/ISA Devices
776249-05
-
34-Pin Female RTSI to 34-Pin Female RTSI Ribbon Cable - The RTSI Cable, sometimes referred to as RTSI, connects RTSI bus connectors on adjacent NI plug-in boards. The RTSI Cable is offered with different numbers of ribbon connections and in different lengths.
-
Product
30U (52") Non-Insulated Bus Bar
BB-52
-
30U (52") non-insulated bus bar provides cabinets with recessed rail option and a convenient, isolated common grounding mechanism.
-
Product
PXI 4 Slot BRIC Module, 1 Resource Distributor, 1 Bus Matrix Inputs
40-569B-011
-
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-011 is a 4 slot module fitted with 1 Bus Matrix Inputs card and 1 Resource Distributor card.
-
Product
A²B® Automotive Audio Bus Solution
ITD 1024
-
ITD 1024 is an off-the-shelf solution for A²B®, an emerging automotive audio bus. In combination with a comprehensive set of software tools, ITD 1024 allows rapid testing of various A²B® components such as audio speakers, amplifiers, microphone arrays, sensors, and actuators.
-
Product
PXI 8 Slot BRIC Module, 2 Resource Distributor, 5 Bus Matrix Inputs
40-569B-125
-
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-125 is a 8 slot module fitted with 5 Bus Matrix Inputs cards and 2 Resource Distributor cards.
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
-
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
PXI 8 Slot BRIC 368x8 1-Pole Dual Analog Bus (8 sub-cards)
40-560A-121-368X8-M
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8-Slot BRIC Matrix, 506x8, 1-Pole (11 sub-cards) Dual Bus
40-560B-121-506X8-M
-
The 40-560B-121-506x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays
-
Product
PXI Dual Bus 64-Chan 2A Fault Insertion Switch
40-190B-102
-
The Dual Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
24U (42") Non-Insulated Bus Bar
BB-42
-
24U (42") non-insulated bus bar provides cabinets with recessed rail option and a convenient, isolated common grounding mechanism.
-
Product
PXI Single Bus 32-Ch 2A Fault Insertion Switch
40-190B-201
-
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
