-
Product
21.5" Full HD Industrial Monitor With PCAP Touch Control, Direct VGA, And DVI Ports
FPM-7211W
-
21.5" Full HD TFT LED LCD16:9 widescreen aspect ratio, increases viewing area by 40%Supports 10-point multi-touch control via USB interface in Windows 7/8/10 OSSlim design enables easy installationSupports various mount options: panel, wall, desktop, and VESA armTouchscreen with reliable glass surface and PCAP touch controlRobust system with SECC chassis and IP66-rated magnesium alloy front panelOSD control buttons on rear panelLockable I/O connectors
-
Product
Electronic Control Units
-
Self-contained engine management system and data logger for race engines up to eight cylinders. The unit is complete with integrated ignition and injection drivers and so needs no external units to run an engine.
-
Product
Digital Timing and Waveform Controller
Ice Bloc DCS
-
Ice Bloc DCS is a highly versatile sequencing system with multiple high-speed digital I/O, analogue outputs and a four-channel digital synthesiser. The DCS sports both single-shot, burst and infinite loop sequence capability. Designed to handle the demands of experimental control required for cold atom experiments, its compact form factor with customisable software interface allows easy integration with your experiments .
-
Product
Serial Production Mark Quality Control
-
The control system is based on the Sick IVC smart camera, which not only captures, but also processes the image. After training on the font samples, the system practically does not require the operator's attention in addition to setting the current marking for control. The character set can be specified by the operator or transmitted via the interface from the printer or from the enterprise information system.The camera software works autonomously: it loads all settings from the camera's permanent memory, initializes the backlight electronics and waits for a signal from the object presence sensor. When a signal is received from the sensor (an object in the shooting area), the camera captures the frame, searches for markings and analyzes the symbols for their compliance with the exemplary set.
-
Product
Qualification and Quality Control Tests
Techsquare
-
New IEC standards, IEC 60034-18-41 and IEC 60034-18-42, have been issued to define the procedures for testing partial discharge inception voltage and the long-term performance (endurance) of Type I and Type II insulation systems used in rotating machines fed from voltage converters. Voltage impulse generators are required at least to test turn insulation, but they would be recommended for any testing under power electronics supply because of their capability to simulate the real electrical stress conditions. More generally, any type of electrical insulation system when subject to impulsive voltage waveform during life should be carefully evaluated in terms of partial discharge and endurance behaviour. This is why voltage impulse generators able to provide impulses with controlled amplitude and frequency are needed to face this new testing challenge.
-
Product
Automatic Power Control system
-
The Automatic Power Control system cuts the incoming power supply to a traction unit for short periods. This is required where power supplied from one part of a power distribution system in separated from another by a neutral section. Its fitment prevents damage to the power distribution system or the vehicle.
-
Product
Diode Driver & Laser System Controllers
-
The laser controllers provide a simple method of controlling Lumina and other popular laser diode drivers or full laser systems. They include the ability to easily control current levels, pulse modes, and interlock controls as well as monitor voltage and current levels as well as q-switch triggering, external triggering, sync output, and additional I/O signals.
-
Product
Space Flight Gimbals & Controllers
-
Precision gimbals for pointing and tracking, stabilized platforms, and pedestals have been a specialty of CAES for more than 60 years. We have deep and broad experience in both terrestrial and space applications.
-
Product
Thermal Vacuum Chamber & Control
-
Based on several successful deliveries of complex DAQ systems, WinSoft was selected by 2 major satellite manufacturers to design and build a DAQ and Control systems which are connected to various thermal vacuum chambers - all connected to a central database.The chambers are used for environmental testing. The data collected by the DAQ system is recorded continuously every few seconds over a period of a few months.
-
Product
2-port LAN Module With Intel® X540 Ethernet Controller
AX93317
-
The AX93317 is a dual-port LAN module built with an Intel® X540 10 GbE Ethernet controller that provides acceleration technologies to optimize the processing of network data traffic, including the Intel® DPDK, SR-IOV and VMDq. The AX93317 LAN module features dual 10 GbE RJ-45 ports and a PCIe 2.0 x8 golden finger, along with a compact design adapted specifically for Axiomtek’s 1U and 2U rackmount network appliances, allowing customers to streamline their individual network infrastructure deployments to fulfill fast-changing networking demands quickly and cost-effectively.
-
Product
Pipeline Integrity and Corrosion Control
-
The integrity of buried pipelines is of paramount importance for safety, environmental and cost reasons.
-
Product
Rotary Thermal Shock Chambers
TS Series
-
A Bemco exclusive product, the TS Series of Turboshock Rotary Thermal Shock Chambers feature an electrically driven, 180 degree reversing, rotating wall located between two chambers, one hot and one cold. Two loads can be handled simultaneously. Front loading and rear access doors allow full entry to each zone.
-
-
Product
cRIO-9064, 667 MHz Dual-Core CPU, 512 MB DRAM, 1 GB Storage, and Zynq-7020 FPGA, 4-Slot CompactRIO Controller
783831-01
-
667 MHz Dual-Core CPU, 512 MB DRAM, 1 GB Storage, and Zynq-7020 FPGA, 4-Slot CompactRIO Controller - The cRIO-9064 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. Additionally, the cRIO-9064 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, one USB host, one USB device, and one RS-232 serial. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
SCR CONTROLLED VARIABLE DC POWER SUPPLY
P5085C
-
Shown below is an AC to DC power supply with 4/20 ma interface. Input is 240 VAC, 1 PH, 60 Hz. Output is 0 to 10.5 DC, 130 Amps. This power supply can be interfaced to a PLC system. These units are customized units, built to order.
-
Product
Sine Vibration Control
-
Sine control is one of the two basic and most common excitation modes for Environmental Shaker testing. This control mode performs real-time closed-loop control of swept sine vibration. The m+p VibControl vibration control system allows the user to designate all input channels as control, watchdog and/or measurement channels.
-
Product
Enterprise Session Border Controller
eSBC
-
Session Initiation Protocol (SIP) is the communication technology employed to set up and tear down VoIP phone calls
-
Product
Geophone Testing – Hydrophone Testing – Vibrator TestingVersatile Quality Control System - Three Test Units In One!
Bird Dog 3 - 3 Channels
-
*32-bit, high speed, ADC chip for lower noise and increased accuracy*Three different operation with a single unit*8 Gigabytes of Data Storage, Expandable to 16*GPS based time and location saved for every record*Stable and rugged unit for use in all conditions*Three-Component Test Mode, checks 3 elements at onceto save time and effort*All test data saved in non-volatile memory for later download and retrieval*Connects to PC via Ethernet or optional Wi-Fi, provides control, data download and real time display and analysis of data and results
-
Product
USB JTAG controller
-
The small, lightweight design means the XJLink2 can easily be moved to the Unit Under Test (UUT). Advanced features, like their programmable JTAG signal pin position, switchable power supply and auto signal skew, make it easy to connect to a wide range of circuit boards. Simple to install and use due to the USB plug-and-play ability.
-
Product
High-Performance Industrial Controller
GEVA 1000
-
GEVA is a high-performance industrial controller that offers excellent cost savings for multi-camera vision applications, such as final inspection of large assemblies. As the name implies, GEVA provides expandable Gigabit Ethernet camera interfaces that significantly drive down system cost.At the heart of GEVA is a powerful dual core processor, equipped with high-speed memory resources to tackle the most demanding applications. Two dedicated camera ports are provided, each with enough bandwidth to easily support eight 640x480 mono cameras imaging parts at 60 per second. The camera ports are compatible with a wide range of mono or color, area and line scan GigE cameras in a range of resolutions.
-
Product
Single Mode Fiber Optic Rotary Joints
-
Single Mode Fiber Optic Rotary Joints (FORJ) can be supplied as a stand alone product. Its features can be customized : wavelength, connectors, characteristics of the fiber…
-
Product
Engine Controller
FireLynx
-
The fully programmable FireLynx control module is used for Engine Development, Test and Control as well as directing the real time operation of Fuel Injector Test Stands.
-
Product
Advanced Monitoring and Control System
SEL-734B
-
Schweitzer Engineering Laboratories, Inc.
The SEL-734B with low-energy analog (LEA) inputs provides advanced monitoring and control capabilities for applications, such as capacitor bank control and feeder monitoring. LEA sensor compatibility allows safe, fast, and inexpensive installations. Advanced communications report data to SCADA systems and allow remote operations from a control center.
-
Product
Solid State Synchro Control Transformer and Solid State Resolver Control Transformer
SCT-RCT Series
-
Computer Conversions Corporation
The SCT Series are low cost, miniature, solid state control transformers designed for military and industrial control applications. They will directly replace conventional electromechanical control transformers & thus provide digital control to existing analog servo systems. They simultaneously accept a 3 wire synchro input (0) and a digital angle input (0), and provide an ouput which is the sine of the difference between these two input angles (A sin wt sin (0-0) ("wt" is the synchro excitation frequency).
-
Product
Automatic Power Factor Controller
-
Nippen Electrical Instruments Co.
NIPPEN Model UNO+ is used for measurement and control of PF using Reactive power compensation. Capacitor banks are suitably switched ON and OFF automatically to provide necessary compensation.An Intelligent switching algorithm (Wear leveling) ensures uniform aging of the capacitors used to achieve the Target PF. An Alarm function ensures protection of capacitor banks against abnormality in voltage, current and sets value of capacitors whenever these are beyond the higher and lower threshold limits.CT polarity is automatically sensed internally in the event of reverse connection.
-
Product
Rotary Field Direction Indicator According to DIN EN 61557-7 (VDE 0413-7)
-
PeakTech Prüf- und Messtechnik GmbH
Direction indicators are indispensable for use in the electrical assembly of three-phase motors. This offers two different functions for displaying the direction of rotation. I
-
Product
Linear Motion Systems
-
The diverse range of Thomson guide and drive systems can be configured to work in harsh environments, at high speeds and in high-precision applications — all while striking a balance of performance, life and cost. RediMount motor mounting adapter kits are now available as standard on all systems, making the process of choosing and mounting a motor much faster and easier.
-
Product
Motion Control Terminal Board for Mitsubishi J2S-A Servo Amplifiers
DIN-814M0
-
This well-designed motion control terminal board is for the users who use Mitsubishi J2 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
Product
Automated Video Quality Control
VQFlow
-
Automated video quality control, what content preprocessing, video post production and video service providers are asking for, is now available and ready to be integrated with any ingest or content management system.
-
Product
MIPI I3C Sensor Controller
I3C
-
The main purpose of MIPI I3C is to standardize sensor communication, reduce the number of physical pins used in sensor system integration and support low-power, high-speed and other critical features supported by I2C and SPI.
