-
Product
Electrical DfT & Fault Coverage Analyzer
TestWay
-
TestWay's electrical DfT analyzer enables designers to validate designs at the schematic capture stage, to ensure that adequate measures have been included to comply with the manufacturers test requirements. The ability to verify that PCB designs have been developed with adequate Design-for-Test in mind, is key in determining the most effective test strategies and accurately calculating fault coverage, which is crucial in improving competitive advantage, lowering cost and ensuring product quality.
-
Product
Vector Network Analyzers
-
The Teledyne Test Tools range of T3VNA Vector Network Analyzers consist of two models with a Vector Network Analysis frequency range of 10 MHz up to a maximum of 3.2 GHz and a Spectrum Analysis frequency range from 9 kHz up to a maximum of 3.2 GHz. The small footprint and easy user interface is augmented by a high performance specification with many advanced measurement functions and capabilities.
-
Product
Electrical Circuit / Wire Harness Analyzer
ECAD System 2005
-
The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.
-
Product
Netlist Analyzer
GateVision
-
GateVision PRO is the third generation of graphical netlist analyzers from Concept Engineering. Completely rewritten to run on modern 32/64bit platforms, GateVision PRO provides the designer of even the largest chips with intuitive design navigation, schematic viewing, logic cone extraction and interactive logic cone viewing for debug support and design documentation.
-
Product
Gas Concentration Analyzers
-
Picarro Gas Concentration Analyzers - Acetylene, Ammonia, Carbon Dioxide, Carbon Monoxide, Ethane, Ethylene, Ethylene Oxide, Formaldehyde, Hydrogen Chloride, Hydrogen Flouride, Hydrogen Peroxide, Hydrogen Sulfide, Methane, Nitrous Oxide, Oxygen, Water, etc.
-
Product
TorqueLab® Torque Analyzer
LTT-Series
-
The torque analyzer is designed for calibrating tools, joint testing, auditing and measuring torque. Torque tools go out of calibration with use. To maintain consistent accuracy, torque tools must be checked periodically for wear or defective parts. A power or hand torque tool is a measuring tool that must be properly calibrated and maintained. The LTT-Series is an advanced torque testing and documentation solution. Using a quality torque tester makes a safer world through accuracy and precision. Controlling torque is essential for companies to ensure their product’s quality, safety and reliability isn’t compromised.
-
Product
PhyView Analyzer
-
Comprehensive, fully automated plug’n play Ethernet10/100/1000 interface testing offering unmatched simplicity and productivity. Test LAN interfaces on any product.
-
Product
Total Sulfur Analyzer
Model 6200T
-
Teledyne Analytical Instruments
The Model 6200T Total Sulfur Analyzer utilizes proven UV fluorescent technology to continuously detect sulfur found in inert gas streams. An internal, quartz catalytic converter is employed to convert the sulfur, when mixed with scrubbed ambient air, into SO2 via higher temperature oxidation. An internal vacuum pump is employed to draw both the sample and the ambient air into the converter. The converted sample gas is fed to the fluorescence chamber where it is then exposed to ultraviolet radiation.
-
Product
Explosion Proof Paramagnetic Oxygen Analyzer
Model 3020M
-
Teledyne Analytical Instruments
The Model 3020P is a versatile microprocessor-based instrument specifically designed to detect oxygen in a variety of gases. It is a precise, cost effective instrument capable of measuring percent oxygen in as low as the 0-1% range. Drawing on the solid performance of the 3000 series control platform, the 3020M provides the user with a wide variety of features and options to satisfy virtually any application.
-
Product
DYNAMIC SIGNAL ANALYZERS
900 Series
-
The new SignalCalc 900 Series software makes the process of defining a test, making measurements, analyzing data and generating high-quality reports easier than ever before. All setup, project, test article, and customer information is saved along with measurement data in a database. Easily search for data from different test runs and test types for analysis and report generation.
-
Product
Multi Channel Analyzer
BOSON
-
Baltic Scientific Instruments, Ltd
Spectrometric device BOSON acquires and displays spectra with overlapping by energy up to 1000 timesNo resolution deterioration at operation in the beginning of spectrum energy rangeStable operation with preamplifiers of TPR type with output voltage swing up to +/- 10 V and reset duration up to 250 usAutomated P/Z adjustmentImproved dead time correctionSoftware-based spectrum stabilizationSetting and control of all parameters using colour LCD display with touch screenComplete remote control of Boson via software on PCAuto BLRAnalogue time dependent shapingSpectrum stabilizationDead time correctionOperation with preamplifier TPR
-
Product
WLAN Network Analyzer
NX-1
-
NX-1 is a high performance dual band wireless LAN network analyzer for SMB and Enterprise environments with 802.11a/b/g/n support. NX-1 provides an easy to understand simple menu that can be used even by those who are not familiar with specialized wireless LAN knowledge.
-
Product
Handheld Digital Spectrum Analyzer
RF Explorer - 3G Combo
-
This model includes a WSUB1G baseline unit plus an RFEMWSUB3G Expansion Module conveniently assembled and tested. It comes with two SMA connectors and two antennas,a nice Nagoya NA-773 wideband telescopic antenna for all Sub-GHz frequencies and a whip helical for 2.4GHz band. Additional, specific band antennas may be needed to cover efficiently some of the frequencies supported.
-
Product
12V Auto Battery And Charging System Analyzer
1947
-
Peaceful Thriving Enterprise Co Ltd
1. Check for batteries, regulators and alternators. 2. For all 12V system vehicles, with LED indicator that helps pinpoint problems for fast troubleshooting. 3. Other car battery testers are also available.4. With CE Approval.
-
Product
Hybrid Signal Analyzer
DANEO 400
-
DANEO 400 is a hybrid measurement system that records and analyzes all conventional signals (voltages, currents, hard wired binary status signals) and messages on the communication network in a substation.
-
Product
Optical Analyzers
DNIRA™
-
Neolitics’ DNIRA™ is a real-time, in-line process NIRS that delivers the performance and accuracy of a precision laboratory instrument in a compact, robust, in-line design. It’s easy to install and requires virtually no maintenance post-installation, eliminating the time and difficulty required to keep systems calibrated and the difficulty in replicating or scaling applications within a manufacturing environment.
-
Product
Spectrum Analyzer Modular AFM AXIe
-
The software and hardware complex "Modular Spectrum Analyzer AFM AXIe" for the analysis of RF signals with a frequency of up to 10 GHz is intended for use in automated testing programs, research in the frequency domain of periodic signals in the RF and microwave ranges, as well as for analyzing the parameters of signals with analog modulation (AM, World Cup, FM).
-
Product
Trace Moisture Analyzers for Natural Gas Quality and Petrochemical Applications
-
Michell Instruments’ process moisture analyzers provide continuous, online monitoring of dew point and trace moisture content.
-
Product
Trace-Level UV Fluorescence SO2 Analyzer
Model T100U
-
Teledyne Advanced Pollution Instrumentation
The Model T100U Trace-level SO2 analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. It uses the proven UV fluorescence principle, and is designed to allow ultra-sensitive SO2 measurements while still meeting the requirements for use as a US EPA compliance analyzer.The analyzer uses both the light and dark phases of the pulsed UV light source to continuously detect and correct for electronic noise, giving exceptionally stable and sensitive performance. A separate UV detector allows the instrument to continuously correct for variations in lamp intensity. Exceptional stability is achieved with the use of an optical shutter to compensate for PMT drift, and a reference detector to correct for changes in UV lamp intensity. A hydrocarbon "kicker" and advanced optical design combine to prevent inaccuracies due to interferents.
-
Product
Fixed Power Analyzers
-
Network analyzers are devices that are essential for measuring electrical parameters and controlling industrial processes. They provide the user relevant, real-time information for managing energy consumption and checking the quality of supply and consumption in their installation. They offer multiple communication options, inputs and outputs to manage any alarm that may appear in the installation, and provide analyses and reports on the performance of their network.
-
Product
Consumer Safety and RoHS Handheld XRF Analyzer
-
DELTA Consumer Safety & RoHS Handheld XRF Analyzers allow for testing large quantities of consumer & electronic products anywhere, anytime. Get simple, fast, nondestructive regulatory compliance screening for Pb, Cd, Hg, Br & more. Use for ASTM Method F2617-08, HR4040, CPSC, CPSIA & more.
-
Product
Chloride/Sulfate Analyzer
Thornton 3000CS
-
The METTLER TOLEDO Thornton 3000CS Analyzer is an on-line instrument for direct measurement of chlorides and sulfates in pure water and power cycle chemistry samples. The analyzer continuously monitors these highly corrosive contaminants to assist in corrosion control and minimizing damage to critical power plant equipment. Early, unambiguous detection of trace levels of chloride and sulfate ions is provided with minimal operator supervision.
-
Product
Automated Memory Analyzer
Volatility
-
Volatility has become the world’s most widely used memory forensics platform. The project is supported by one of the largest and most active communities in the forensics industry. Volatility also provides a unique platform that enables cutting edge research to be immediately transitioned into the hands of digital investigators. As a result, research built on top of Volatility has appeared at the top academic conferences and Volatility has been used on some of the most critical investigations of the past decade. It has become an indispensible digital investigation tool relied upon by law enforcement, military, academia, and commercial investigators throughout the world.
-
Product
Multi Purpose FT-NIR Analyzer
MPA II
-
The MPA II is the result of more than 40 years of experience in the engineering and production of FTIR and FT-NIR spectrometers. It is a powerful tool for developing sophisticated calibration methods for your laboratory or process needs, yet an easy to use QA/QC instrument for routine work. With its modular technology, it can be configured individually for each analytical task.
-
Product
WDXRF Wafer Analyzer
2830 ZT
-
The 2830 ZT wavelength dispersive X-ray fluorescence (WDXRF) wafer analyzer offers the ultimate capability for measuring film thickness and composition. Designed specifically for the semiconductor and data storage industry, the 2830 ZT Wafer Analyzer enables the determination of layer composition, thickness, dopant levels and surface uniformity for a wide range of wafers up to 300 mm.
-
Product
CPRI Sniffer & Analyzer
SIQMA SC2820
-
The SIQMA SC2820 CPRI Analyzer is the market’s highest-performing, lowest-cost CPRI test instrument. Unlike other solutions, which have been retrofitted to support CPRI, the SIQMA’s high-performance signal processing hardware was designed specifically for CPRI applications. Because of this, the SIQMA SC2820 offers unparalleled performance at half the price of other CPRI analyzers.
-
Product
Digital Circuit Breaker Analyzer
CT-7000 S3
-
The CT-7000 S3 is Vanguard’s fourth generation EHV circuit breaker analyzer. The CT-7000 S3 is available with 3 (part number 9021-UC) or 6 contact timing channels (part number 9100-UC). The CT-7000 S3 can fully analyze a circuit breaker’s performance by measuring the main contact and resistor contact time, stroke, velocity, over-travel, bounce back and contact wipes. Both contact and motion analysis can be performed on all circuit breaker operations (OPEN, CLOSE, OPEN-CLOSE, CLOSE-OPEN, and OPEN CLOSE-OPEN). The CT-7000 S3’s timing window is selectable between 1 second, 10 seconds, and 20 seconds.
-
Product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783156-01
Signal Module
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
Product
LDE Electrical Analyzer
-
The Cadence LDE Electrical Analyzer helps designers identify, analyze, and minimize the effect of parametric issues associated with manufacturing variability to improve design performance.
-
Product
Automated Membrane Permeation Analyzer
MBR
-
The MBR is a dedicated membrane testing reactor for studying the selective gas permeation properties of membrane materials for separation and purification applications. It is a fully automated system, and is supplied with an integrated close-coupled mass spectrometer.
