-
Product
XMC Module Carrier PCI Express x 4
SK2-SESSION
-
SK2-SESSION is a bidirectional 4-lane PCI Express® Gen3 redriver, for optimum 8GT/s high speed signal integrity, and can be installed into any peripheral slot of a CompactPCI® Serial backplane.
-
Product
PCI System Timer
SKU-051-01
-
The PCI System Timer uses a hardware clock to synchronize IP signals. This hardware-based solution provides accurate clock timing for Asterisk® open-source PBX software.The timer supports variable clock timing intervals. You can configure the clock interval during startup. Currently, the PCI System Timer supports clock interval ranging from 1ms to 64ms.
-
Product
High-Voltage Test Device
PGK 260 HB
-
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit. *Testing of medium- and high-voltage cables * DC voltage testing of up to 260 kV output voltage with positive or negative polarity * AC voltage testing - up to 190 kV for switchgear, busbars and insulating elements * Easy-to-maintain 2-piece design
-
Product
Battery Crush Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s battery crush test chamber is used to battery crush test. This battery testing equipment simulates the conditions of the battery crushing and display comminution result.
-
Product
Headlamp Testing
-
Boston Beamsetters offers remarkable value with our traditional high quality construction and ability to test modern gas filled headlamps. Lateral vehicle adjustment is achieved by using dual lasers - from the top of the mounting pillar and additionally from a through-the-lens laser making accurate testing simple and easy.
-
Product
CE Mark Testing Lab
-
The CE mark is a mandatory European marking for certain product groups to indicate conformity with the essential requirements set out in European Directives. In order to use the CE mark on a product, the manufacturer must draw up an EU declaration of conformity (DoC) in which the manufacturer attests to conformity with all relevant New Approach Directives (NADs) and takes sole legal responsibility. In some instances, a NAD may require a Notified Body to issue a Certificate of EU declaration of conformity (DoC) Conformity in order to verify the performance of the product or constancy of the production process (Factory Production Control, for example).
-
Product
PCI Express to VME Interface
SIS1100-E2/3104-2
-
The SIS1100-e2/SIS3104-2 interface/bus coupler is the choice for demanding VME readout applications. VME block tranfser speeds up to 160 MByte/s are readily accomplished in conjunction with state of the art VME slave hardware.
-
Product
Continuous Testing Platform
BlazeMeter
-
BlazeMeter was designed and built by engineers who are passionate about open source. From mobile to mainframe, IDE or UI, bring teams together in a single platform with shared visibility, tests, and reports.
-
Product
ESD Test Simulator
ONYX16
-
The ONYX is a state of the art electrostatic discharge simulator available in 16kV or 30kV versions. It is the most ergonomic 30kV ESD gun without an additional base control unit that can be battery or mains operated. The easy to use touch screen, ergonomic design, modular RC units, multilingual interface, remote control software, built-in LED light and temperature & humidity display allows for trouble-free use of the ONYX in all types of test sites.
-
Product
Mobile, Hardened Test Set
MBX1
-
With the MBX1 platform and our software, you can easily test SCADA and substation automation systems (SAS) in a highly secure way. The mobile solution allows you to perform quick assessments and temporary monitoring, e.g. during commissioning.
-
Product
Temperature & Battery Testing
-
Conducted to determine how a battery performs under different temperature ranges.
-
Product
Reverse Compact XMC-to-PCI Express (PCIe) Adapter
8260
-
Our Reverse Compact XMC-to-PCI Express (PCIe) Adapter 8X (8260) permits use of a standard VITA 42.3 air-cooled XMC, or VITA 20 conduction-cooled XMC, in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC, and 10 mm mezzanine stacking height is supported.
-
Product
Hazardous Locations Product Testing
HazLoc
-
F2 Labs can assist you with your hazardous location testing needs. We can perform the HazLoc product testing required to ensure that your product won’t cause a fire or explosion in an area where flammable or combustible materials (such as dusts, gases, fibers or vapors) are present. The product must be designed using various methods of protection.
-
Product
Thermal Cycling and Humidity-Freeze Test
-
King Design Industrial Co., Ltd.
*10.4" TFT LCD, touch-type Chinese/English display controller.*Temperature/humidity setting procedure, LCD curve display device (set to “curve display”).*Chinese/English/LCD operation/troubleshoot/guiding window.*State-of-the-art intelligent auto-dispatch “heat load value” coolant servo valve flowrate algorithm control.
-
Product
Chemical Emissions Testing
-
Underwriters Laboratories Inc.
As a global leader in the science of safety, UL evaluates products and materials to determine their impact on indoor air quality and, by extension, human health. Whether your products need to meet the emissions requirements of environmental certifications or regulations or you simply wish to have a better understanding of your products'''' potential impact on the indoor air for legal or risk assessment purposes, UL is your partner for developing healthier, lower emitting products.
-
Product
In House Testing
-
Burnsco Environmental Test Chambers
Burnsco Technologies Inc recognizes that many customers have one-time testing requirements or, from time to time, an overload of testing. With that in mind we are pleased to offer you a test center with a unique difference!
-
Product
8-CH Relay Outputs & 8-CH Isolated DI PCI Cards
PCI-7250/7251
-
ADLINK's PCI-7250/7251 provide 4-CH SPDT (Form C) & 4-CH SPST (Form A) relay outputs and 8-CH isolated digital inputs. The status of each relay output is represented by an onboard LED. When the relay is in SET condition, its corresponding LED will turn ON, and on the contrary, it is OFF. All digital input channels are nonpolarity, optically isolated, and may be set to use RC filter or not. The devices are suitable for collecting digital inputs in noisy environments. The PCI-7251 is an 8-CH relay outputs and 8-CH isolated DI extension card of the PCI-7250. All the I/O functions of PCI-7251 are the same as those of the PCI-7250. The PCI-7251 has to be connected with PCI-7250 and the bus interface is controlled by the PCI-7250. Up to three PCI-7251 cards can be connected to one PCI-7250, therefore, expanding the PCI-7250's DIO from 8 DIO to maximum 32 DIO.
-
Product
Fuel Cell Test Systems
-
For 100Watt DMFC single cell testCompact sizeConsists of electronic load, gas/liquid controller, humidifier and methanol pump etc.
-
Product
Performance Testing
-
LOAD TESTINGEvaluates software behavior under a specific expected loadVOLUME TESTINGEvaluates software productivity under an increasing volume of stored and processed dataSTABILITY TESTINGDetermines the effect of configuration changes on the system's performance and behaviorSTRESS TESTINGIdentifies the upper limits of software capacitySCALABILITY TESTINGMeasures software capability under increased processing power and architecture changesCONFIGURATION TESTINGDetermines the effect of configuration changes on the system's performance and behavior
-
Product
Global Market Access Testing
-
Helping you reduce the delays and costs of multiple testing to achieve market entry into a variety of global destinations with comprehensive services, unmatched expertise, and a worldwide footprint.
-
Product
MEMS Optical Sensor Test
-
For optical sensor test Cohu offers a variety of solutions being driven by requirements for tri-temp, parallelism and stimulus spacing. Customized optical stimulus units are integrated into Cohu’s test handling systems. For light detector test, we implement different types of light sources, such as infrared, ambient- and colored light. We offer different solutions for 3D image sensors combining emitter and receiver tests of LiDAR, Time of Flight and Structured Light devices.
-
Product
PCI 3-Channel Precision Resistor Card
50-297-103
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Track-Signal Test Meter
Model TRSIG-1
-
Aplab Track-Signal Test Meter incorporates Digital Signal Processing based design to provide high accuracy and stability. It is designed for level measurement of selected frequencies. It also provides functionality of AC and DC voltage measurements.The purpose of Track-Signal Test Meter is to make adjustments, control measurements and inspections on both audio frequency track circuits of types FTGS 46, FTGS 917 and also for TI21M type track circuits (now known as BI track 300) for the measurement of eight frequencies from 5700Hz to 8500Hz for metro applications. Its compactness and battery operation render the unit particularly suitable for portable applications in maintenance and for level measurement in communication systems.
-
Product
Custom Test Targets & Charts
-
Our customers in industries that require camera or scanner image evaluation certainly know the challenges that come from finding the perfect target for a specific system and measurement. Thankfully, we at APPLIED IMAGE know these challenges just as well. The ability to freely customize a target has proved important for our customers to get the image evaluation tools they need. Our sales engineers are experts in different types of targets and specifications that will give you the best results for your project, and will guide you through the process from start to finish.
-
Product
Eddy Current Test System
CIRCOGRAPH® Product Family
-
Foerster Instruments, Incorporated
The CIRCOGRAPH eddy current test system with rotating probes guarantees maximum detection sensitivity for exposed longitudinal surface defects on bright material. The test system is primarily used for wire drawing machines, Cu tube rewinders, and finishing sections in the bright steel sector. The individually tailored test systems by FOERSTER can be fitted with rotating sensors or CIRCOSCAN rotating discs. They scan flat and profiled material, e.g. when testing rails and billets.
-
Product
Loss Test Sets
-
These instruments combine up to 6 sources, a power meter & optional VFL in one unit.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 127 Ohm
50-293-012
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Tactical Radio Test Set
CTS-6100
-
The CTS-6100 brings an entire test bench to your front lines. Enable your technicians to detect equipment faults and verify operational capabilities at the I- and O-levels, saving valuable diagnostic time and cost.
-
Product
TurboFan Test Cells
-
Atec, Inc. is an industry-preferred provider of full scale TurboFan test cell design, construction, maintenance, and refurbishment. Our seasoned aeroengine professionals and comprehensive network of international locations and resources provide our customers with unparalleled expertise and value for their most critical and complex test cell projects.
-
