-
product
Programmable 70W Electronic Load
MightyWatt R3
The All-New MightyWatt revision 3 turns your Arduino Uno R3 or Arduino Zero (M0/M0 Pro) into an electronic load capable of dissipating 70 Watts in a very small form factor. Ideal for testing power supplies, batteries, solar cells, fuel cells or power amplifiers. MightyWatt R3 has a research-grade electronics and is aimed not only at hobbyists but also at professionals.
-
product
LED Test Programmable DC Electronic Load
IT8912E Series
IT8900 series high accuracy LED specific testing electronic loads can simulate the real output of LED lights with different characteristics.Their specific circuit can realize CR-LED mode, adjustable frequency, duty ratio PWM dimming output port (frequency: 20Hz-2KHz), I-pp/I-max measurement function can test current ripple and start up surge current of LED constant flow source. Voltage and current testing speed can reach 50KHz. IT8900 series provides CR-LED / CC / CV + CC / CR /CW and other working modes, built-in USB / RS232 / GPIB communication interface. Widely used in LED driver power dimming test.
-
product
PXI 10W Programmable Resistor Module, 1-Channel, 1.5Ω to 3.55kΩ
40-253-023
The 40-253-023 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 3.55kΩ with 1Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Programmable LCRZ Meter
DU-6212/6215/6216
Delta United Instrument Co., Ltd.
Wide Measuring Range & High accuracy 0.1%Zeroing Offset FunctionProvided HI/LOW limit and BIN Sorting comparator function, to meet your needed.100 sets of memory, can be saved test parameter and comparator setting, easy to use.Cover up free, system firmware upgrade can be update via RS-232, easy to maintenanceEasy Test Condition Setting with Auto Parameter Selection & Auto Ranging Function High speed FADC, max. test speed up to 55 meas./sec, faster your automation equipment240*64 Graphic LCD display, can be read the reading clearly and easier.User friendly programmable interface, easy to useProvided RS-232C and Handler combinatorial interface option, to meet your needed
-
product
High Power Programmable AC Source
Chroma Systems Solutions, Inc.
Simulate various AC line input conditions and measurement of critical characteristics for products under test
-
product
Programmable Relays
Omega offers a wide selection of programmable relays. From universal remote I/O modules to pressure switch accessories, you'll find everything you need to complete your application here.
-
product
Programmable Linear DC Power Supply, 3 Output, 0-32V/0-3A, 1.8V/2.5V/3.3V/5V/5A
T3PS33203P
Programmable Linear DC Power Supply, 3 Output, 0-32V/0-3A, 1.8V/2.5V/3.3V/5V/5A.
-
product
Programmable Step Attenuator, DC to 40 GHz, 0 to 11 dB, 1 dB steps
84904L
The Keysight 84904L programmable step attenuator offers coaxial measurements to 40 GHz in a compact, rugged design. It offers repeatability of better than 0.03 dB, excellent life (greater than 5 million switching cycles per section) and an attenuation range of 0 to 11 dB in 1-dB steps. This latest design evolution sets new standards for size and performance. High attenuation accuracy and low SWR are achieved through the use of miniature thin-film attenuation cards composed of high-stability tantalum nitride film of saphire substrate. Insertion loss is outstanding, with with only 2.4 dB of loss at 40 GHz. The compact size of the unit, 35% smaller than the Keysight 8495/7 (26.5 GHz) family, allows for easy integration into instruments and ATE systems.
-
product
Programmable Delay Line Instrument
XT-100-OEM
With the XT-100-OEM, all the capabilities and precision of the XT-100’s trombone technology can be built right into your own system. This product is intended primarily for OEM applications so you have a streamlined solution for precision phase shift or programmable delay.
-
product
Multi-Channel, Programmable Current Source
CS-48-100
The Model CS-48-100 is a multi-channel, programmable current source. Developed for both semiconductor and digital superconductor electronics, it is computer-controlled and features 48 low noise current source outputs. Each source output has the capability to both set and read back currents and can be set to a zero current high Z mute state. Each of the 48 sources are optically coupled for control and are sourced from their own secondary winding for complete galvanic isolation. The device consumes a maximum of only 80 W and handles a maximum load current of 4.8 A total over all outputs. Operating over a range of 0-100 mA on each channel, the device features accuracy of +/-25 ?A. The mute state can be set thru a rear panel interlock or from the front panel button for maximum circuit protection. The unit can be mounted in a standard-sized rack.
-
product
Isolated Programmable Multifunction Counter Board
APCI-1710-24V
Wide application possibilities through free combination4 modules with numerous functions quickly and easily programmableEach of the 4 modules is programmed with a function. The 4 modules can either be programmed with the same function or freely be combined with 4 different functions.
-
product
Programmable DC Laboratory Power Supplies Linear
Programmable DC Laboratory Power Supplies Linear.
-
product
Programmable AC Power Source
LSP-500VAC
• Applied with the AC-DC-AC inverter technology and digital waveform synthesis & waveform feedback technology, low distortion power; • Applied with entire cycle high-precision measurement technology and high-speed sampling technologies, panel of instrument will directly and accurately displays the power output of the voltage, frequency, current, active power and power factor to achieve the integration of the source table; • Applied with SCM control and measurement technology, high intelligence; • Applied with zero output impedance technology, the output equivalent impedance is almost zero and further improve the stability of power supply; • Applied with isolated floating output technology, the power output and input have good isolation, floating output, conducive to make sure power itself safety and operator’s safety; • Perfect voltage, current anomalies and overheating protection, improve the reliability of power supply; • Applied with power limiting technology to avoid strong interference on the power grid and other electrical equipment, while facilitating reliable operation of the power supply itself; • The input voltage can be option via a toggle switch of panel mains 110V/220V; • The initial phase and end phase of the output voltage waveform can be set {0°-359° (±1°)}; • Measurement process can be programmed to control (1 to 50 memory groups, 1 to 9 steps for each memory group);
-
product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 127 Ohm - SPST
40-294-112
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
FPGA-Based Ultra-Fast Flash Programmer
XJFlash
XJFlash is an FPGA-based advanced and innovative method that uses JTAG for high-speed in-system programming (ISP) of flash memories – all serial and parallel flash devices are supported. The most common use of XJFlash is programming the SPI/QSPI NOR flash used to configure an FPGA.
-
product
Programmable Power Modules
Series MST
MST power modules are a group of programmable power supplies that are compatible with Kepco¹s single address, multiple instrument serial control bus. The MST provide precision interactive control in the 200 Watt power class. The housings for MST, either RA 55 or CA400, each contain a slot to accommodate an IEEE 488.2 adapter. If not used, an additional MST power module may be plugged into that slot.
-
product
4-Port In-System Programmer For Silicon Labs
MPQ-C2
Supports Silcon Labs C8051F series devices with C2 Programming Interface Field Upgradeable - always supporting the latest devices Secure image management - protects your IP In-circuit gang programming of up to four devices at once Can be deployed in arrays to program up to 64 devices in parallel Stand-alone, PC-controlled or ATE-controlled operation Automatic device serialization
-
product
PCI Resistor Card 4-Channel 1 Ohm To 63.7 Ohm
50-293-011
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-025
The 40-297A-025 (PXI) and the 42-297A-025 (PXIe) are 9-channel programmable resistors with a range of 1.5 Ω to 13.6 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Programmable Controllers for Advanced Machines & Automation Projects
Vision Series
An award-winning series of programmable controllers (PLC + HMI) , ranging from palm-sized controllers with onboard I/O to large-screen controllers with snap-in I/O. Vision is a true workhorse: reliable, versatile, field-hardened – a cost-effective All-in-One controller.
-
product
Programmable, 2-Channel High-Pass Filter Module
AAF-HP
The AAF-HP series provides 2 programmable channels of high-pass filtering on a plug-in module that is pin compatible with the popular AAF-1F, AAF-2F, and AAF-3F modules.
-
product
Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, P, LL/UL/S/C, Programmable Amplitude Balance
LS-16A-R1-24SPLUSC
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
product
Programmer VVDI MB TOOL
*learning ELV*Read and write CGW / ZGW – OBD*programming and making new keys NEC SMD*generating files keys without time delay (all ROMs)*making new keys BE through IR*read password from BE keys through IR*making new keys modułów throught connector (ECU, Ism, elv, 7g tronic)*EZS lock – making new keys through IR*EZS data edition*With power Adapter very fast counting password on some models (all keys lost)*erasing „fatal error” in ELV
-
product
Programmable Switching DC Power Supply 1 Output, 0-80V, 0-27A, 720W
T3PS80271P
Programmable Switching DC Power Supply 1 Output, 0-80V, 0-27A, 720W.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-154
The 40-297A-154 (PXI) and the 42-297A-154 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 22.3 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PCI Programmable Resistors
Part of our Sensor Simulation family, these PCI programmable resistor cards are ideal for medical, aerospace and automotive applications.
-
product
Programmable Multifunction Counter Board, Isolated, With 2 Function Modules
CPCI-1711
The board CPCI-1710 is a fast multifunction and multichannel counter board for the CompactPCI bus. The strengths of this board are its wide range of applications and high precision and reliability for though industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provides the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied sofware. The flexible programming facilities on this board allow many different user applications to be quickly and easily developed or reconfigured as further requirements arise.
-
product
Programmable Industrial USB 3.0 Hub (8 Ports)
The USBHub3+, an 8-port programmable USB 3.0 Hub. Designed by engineers for engineers - connect the USBHub3+ with confidence to expensive lab or production equipment. Enable/Disable any Downstream Port. Maintain selectable control of data, SS lines, power lines for any port. Monitor Voltage and Current on any/all ports. Supply up to 2.5A per port. Set Current Limits on any port. Select between two (2) Host Connections.
-
product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 31.5Ω
40-251-010
The 40-251-010 is a programmable resistor module with 8 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 63.7 Ohm
50-294-011
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
