-
Product
PCI Express To CPCI Board
MS 1719
-
PCI Express to CPCI card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit cPCI signals from/to the Host System. These cPCI signals are converted into PCI Express using cPCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
-
Product
VXI Register Interface Board
VXI-5524A-3
-
* 3.3V power out instead of 5 V on Digital IO bus connector* All othe specifications same as listed above for the VXI-5524A board.
-
Product
Sonar Boards
-
Low skew between channelsMulti-Board SynchronizationSigma-Delta and Delta-Sigma Analog InputOutput reconstruction filtersUp to 64 Channels per BoardProgrammable Sampling Rates to 500K SPSAuto-CalibrationResolutions: 16-bit, 20-bit, and 24-bitAsk about other features such as GPS Synchronization
-
Product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 5V-HS
APCIE-1564-5V-HS
-
32 digital inputs, 5 V, isolated16 interruptible inputs32 digital outputs, 5 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
Board Cameras
-
e-CAM & See3CAM Series of Camera Boards. e-CAM camera board is e-con's reference design featuring a board camera interfaced to a processor on its high speed CMOS interface. Board cameras are available for Jetson Developer kits and NXP i.MX6 boards. For processors, that don't have the Camera ISP pipeline, e-con Systems provides the complete software stack for raw image sensors. The software stack has a wide variety of features ranging from color correction, gamma correction, dead pixel correction, color space conversion, sharpen filter etc.
-
Product
PCIe Fast Multifunction, Multichannel Counter Board, Optically Isolated, 10MHz RS-422 Inputs
APCIE-1711-10MHZ
-
The APCIe-1711 board is a fast multifunction and multichannel counter board for the PCI Express bus. The strengths of this board are its wide range of applications and high precision and reliability for industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provide the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied software. The flexible programming facilities on this board allow many different user applications to be quickly and easily developed and reconfigured as further requirements arise. Thanks to the FPGA board structure, further counting applications can be realised through software adaptation.
-
Product
CableEye 4-Wire Calibration Verification Board | Cable & Harness Testers
CB52
-
The CB52 is intended for periodic calibration verification of the Kelvin 4-wire resistance measurement module – an optional, add-on module that may be purchased with any new hipot system, or added to an existing high voltage tester as an upgrade.
-
Product
PMC Digital IO Board
MS 1815
-
*Bus Interface:- 32 Bit PCI Bus with PMC Interface*Speed of operation up to 66MHz*Spartan-3AN FPGA based design*128 channel digital I/O signal*Input/output ON state=3.5V to 5.0 max at -24mA*Input/output OFF state= 0.8max at 24mA*16 groups of 8 channels can be programmed as input/output*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
Product
LOAD BOARD
-
The semiconductor manufacturing process is divided into a front process (WAFER) and a post process (PACKAGE). The LOAD BOARD is an INTERFACE device for inspecting the function and performance of a package state IC, which is a post process, It is an INTERFACE key device for inspection. In particular, LOAD BOARD is widely used in non-memory semiconductor inspection equipment.
-
Product
Mini-ITX Embedded Board with 8th/9th Gen Intel® Core™ Desktop Processor
AmITX-CF-G
-
Targeted at gaming customers and system integrators, AmITX-CF-G is a Mini-ITX board specially designed for Gaming. AmITX-CF-G features GLI compliance, easy and flexible configuration, security enhancements, and system resilience. The values of AmITX-CF-G include amplified visual impact, guaranteed system integrity, secure transactions with fast TTM and low TCO, and maximized system uptime. AmITX-CF-G can satisfy application function requirements and meet GLI certification which cannot be offered by other conventional Mini-ITX boards.
-
-
Product
3U PXI Express Board Virtex-5 Medium Speed Quad DAC
SMT759
-
Sundance Multiprocessor Technology Ltd.
The SMT700 module uses a Xilinx Virtex 5 LXT or SXT to implement the interfaces the board provides. The FPGA can be configured either via the onboard flash, or through the Xilinx JTAG header.
-
Product
PC/104 OneBank Board
EMC²-7K410
-
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-Kintex7T to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-Kintex7T also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
Product
Large Board Stencil Printer
MC1200
-
Manncorp's MC1200 SMT large board stencil printer fills application requirements of large-board assemblers with print areas ranging from two feet to nearly four feet in length, making them ideal for LED, backplane and multi-panel assemblies. These big-board printers, priced at one-half to as much as two-thirds less than competing large-board printers, are ideal replacements for slower and less accurate manual printers.
-
Product
FMC SpaceWire/SpaceFibre Board
316
-
The FMC-SpaceWire/SpaceFibre board is an FPGA Mezzanine Card which is designed to extend the capabilities of an FPGA development board by adding support for SpaceWire and SpaceFibre interfaces. The board has four SpaceWire ports with accompanying status LEDs, and two SpaceFibre ports.
-
Product
Dual LGA 3647-P0 Intel® Xeon® Scalable Proprietary Server Board with 12 DDR4, 4 PCIe x16 + 1 PCIe x8+4 PCIe x4, 14 SATA3.0, 8 USB3.0, Dual 10GbE, IPMI
ASMB-975
-
- Proprietary server board with dual Xeon® Scalable processors- DDR4 2933MHz RDIMM up to 1.5TB, support Intel Optane DC Persistent Memory- 14 SATA3.0 connectors (including two M.2 2242)- Four PCIe x16 slots (Gen3) for double-deck cards- Intel® X557-AT2 dual 10GbE ports- 0 ~ 40 °C ambient operating temperature range
-
Product
Screw-Terminal & Power Adapter Board - DC-coaxial-jack connectivity for 1 or 2 External VDC Power Supplies
TE3202
-
- Provides DC-coaxial-jack connectivity for 1 or 2 external 48 VDC power supplies- Provides screw-terminal connectivity for all sense, return, & output lines- May be directly connected to the HD-DB15 on the TE3200 front panel, or extended with a standard VGA extension cable.- Provided header pins for jumpering sense & return lines to channel output & return lines.- Provides a 2-pin header for jumper configuration with only one externally supplied 48VDC input (but, halves the maximum output current)
-
Product
Interface Module for Multimode, Multiprotocol Excalibur 8000 Family of Carrier Boards, a Complete Solution for Developing & Testing 1553 Interfaces
M8K1553Px(S)
-
The M8K1553Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.Each M8K1553Px multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1553Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.Each M8K1553PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: the M8K1553PxS module is NOT compatible to the M4K1553MCH module.The M8K1553Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
32-CH Discrete Input Daughter Board Module
HSL-DI32-DB-N
-
*Slave ID consumption: 2 - N: for 32-CH NPN sinking type sensor inputs or dry contact*Photo couple isolation voltage: 2500Vrms*Input impedance: 4.7KΩ*Input current: ??10mA (Max), ??12.5mA (Peak)*Input voltage: ??40V (Max)
-
Product
Low Voltage Boards
-
- 6 or 8 independently controllable full floating channelsup to 64 V- Up to 60 W Max channel output power- High resolution on voltage set- Programmable TRIP parameter- Programmable ramp up / down- Current generator operation in overcurrent condition- Overcurrent programmable protections- Individual remote sense lines- Up to 0,2 mV voltage monitor resolution- Up to 1 mA current monitor resolution- Voltage ripple smaller than 3 mVpp
-
Product
Thin Mini-ITX Embedded Board with Intel Atom®
AmITX-AL-I
-
The AmITX-AL-I is a low-profile Thin Mini-ITX embedded board supporting an Intel Atom® processor E3900 series, Intel® Pentium® processor N4200, and Intel® Celeron® processor N3350 system-on-chip (SoC). The AmITX-AL-I is specifically designed for customers who need optimized processing and graphics performance with low power consumption in a long product life solution.
-
Product
Single Board Computer
-
Hartmann is proud to partner with Orion Technologies, LLC — a distinguished leader in specialized embedded single board computers (SBC) as well as full system design and development. This cutting edge technology is used in a variety of military, industrial, and commercial applications.
-
Product
Backplanes And Connector Boards
-
Backplane and Connector Boards offer a cost-effective, flexible way to interface Advantech products' I/O features and enable board-to-board expansion.
-
Product
16 Relay Output PCIe Board, 16 Isolated Digital Input Channels, 24V
APCIE-2200-16-16
-
16 electromechanical relays with change-over contacts The PCI-Express 16 relay board APCIe-2200-16-16 has 16 relay output channels and 16 digital inputs, 24 V. 15 inputs are interruptible. The board is especially suited for applications like industrial I/O control, signal switching, alarm monitoring, as interface to machines, for the ON/OFF monitoring of motors, lights etc. in the harsh industrial environment.
-
Product
C012 Communication Board
MS 1728/29
-
- Suitable for standard desktops- Four channel in single board- Up to 10 Mbits/sec operating speed- Low Cost solution- Standard INMOS link protocol- Communicates with transputers- Converts between serial link and parallel bus- Tristate bidirectional bus interface- Memory mapped registers- Interrupt capability- TTL compatibility
-
Product
Compact 3U CPCI Single Board Computer
CP32109
-
LinkedHope Intelligent Technologies Co.,Ltd.
Based on Intel® Bay Trail platform E3800 CPU and Celeron CPU, CP32109 is a compact 3U CPCI single board computer compliant with CompactPCI® specification.On CP32109, there is a CFast interface for system installation, and several peripheral interfaces include SATAII, USB2.0 and GbE.CP32109 integrates Intel® HD Graphics display controller, and supports VGA output.CP32109 has high-performance and low power consumption, and can provide better bandwidth for data transmission. With better bandwidth, ruggedized design and extended operation temperature, CP32109 is extremely suitable for fields and applications that have high requirements on product reliability and applicability.Besides, LinkedHope® provides CP32109 with a wealth of software drivers and BSP, including VxWorks, Linux, Windows, etc., which reduce the workloads of system integrators and product developers, and greatly shorten the time-to-market.
-
Product
NON-CONTACT TEST COMPATIBLE Ultra High Speed Bare Board Tester System(ALL-IN-ONE UNIT)
SX-750SUPERⅣC
-
All-in-one Compact Size TesterAll-in-One type Tester, with built-in PC in the Tester main unitImproved operability with a 10.4" Touch PanelAll the operation screens are optimized for touch-pannel operation.
-
Product
RELIABILITY BOARD (Reliability Test Board)
-
The reliability test board is used for testing of HAST, THB, HTOL, BURN-IN, etc. It is a product that evaluates the environmental test and durability when applied to actual products such as lifetime test, high temperature, low temperature, high humidity and thermal shock
-
Product
Board Level Products
-
MicroImage Video Systems offers many of our products as board level allowing OEM’s (Original Equipment Manufacturers) to utilize MicroImage technology in their own products. While we offer many off the shelf products in board level, we can also offer customized versions with different connections and features in reasonable minimum quantities (starting as low as 25 pcs per order for some products). If you don’t see exactly what you are looking for, ask us, it may be something we have already designed or something we can change easily. Contact us today with your requirements.
-
Product
2MP HDR Jetson TX2/TX1 Camera Board
E-CAM20_CUTX2
-
e-CAM20_CUTX2 is a 2MP HDR camera board for NVIDIA® Jetson TX2 /TX1 developer kit. It has an ability to stream seamlessly at wide temperature range (-40°C to 85°C). It enables an excellent low-light performance and can capture images even under 0.5 lux. e-CAM20_CUTX2 is based on 1/2.7" AR0230AT CMOS image sensor from ON Semiconductor™. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement.
