-
Product
7 Tesla Optical Cryostat
OptiCool®
-
The OptiCool by Quantum Design is a new optical cryostat using an innovative design that puts the sample volume in the heart of your optical environment. A custom 3.8 inch bore, split-coil, conical magnet offers fields perpendicular to the optical table up to ±7 tesla. The highly integrated design means, even with a magnet, your sample isn’t buried inside a large cryostat, far away from the optics. Seven side optical ports and one top optical port allow for optical access to your sample from a wide array of directions.
-
Product
Environmental Testing
-
Among AMERICAN TESTING LABORATORY's environmental chambers is a walk-in stainless steel chamber, which is 40 feet long, 20 feet wide and 8 feet high. One of the largest environmental chambers owned by an independent testing organization in the nation, it allows for simulated environmental testing under conditions ranging from subzero to 200° F with a relative humidity of 5% to 100%, with a ±2% tolerance.
-
Product
Fiber Optic Cable Assemblies
-
Amphenol Fiber Systems International
For applications demanding reliability, traceability and the highest level of quality, a complete plug-and-play cable assembly directly from the manufacturer offers the highest degree of confidence. For these most demanding applications, AFSI specializes in manufacturing custom cable assemblies with quality components and industry-leading workmanship. AFSI is able to assist in designing and producing custom cable assemblies from a set of requirements or building to a customer print. Our highly skilled technicians are trained to a wide variety of industry standard procedures critical to manufacturing harsh environment fiber optic cable assemblies. All AFSI cable assemblies are manufactured by expert technicians in our state-of-the-art, AS9100 certified facility.
-
Product
Optical Modules
-
VI Systems GmbH introduces the fiber coupled 850nm vertical cavity surface emitting laser (VCSEL) transmitter module VM64-850M for data rates of up to 80 Gbit/s. The transmitter module features a V-connector for the electrical input signal and for the optical output a 50/125 multi mode fiber which is terminated with a standard FC/PC connector. The left picture below shows the module. The picture on the right shows an optical eye diagram at 32 Gbaud (64 Gbit/s) in a back-to-back test configuration as tested by partners at the Heinrich Hertz Institute in Berlin.
-
-
Product
CPCI 48 Optically Isolated Outputs Card
CPCI-48OUT
-
The output board consists of FPGA controllers for DC output control. An FPGA provides the timing and control. Each output has its own optical isolation, and supports an open collector output. An PCI controller provides the interface to thehost computer. All I/O is accessible from the front panel.
-
Product
Multi-Mode Fiber Optic To RS-232/422/485 Converter
ADAM-4541
-
2 x ST fiber connectorOperation mode: Point-to-Point, and Ring (half-duplex)Half/Full-duplex, bidirectional transmission modeAutomatic RS-485 data flow controlLED indicator to monitor status
-
Product
Test Automation System for Durability Testing
STARS MATS
-
STARS MATS is a Mileage Accumulation Test System application available with the STARS Automation platform for chassis dynamometer. The application provides test execution, equipment control, refueling, and vehicle state monitoring to perform long endurance test without the necessity of continuous staff presence. Its flexible design offers a wide range a customization, and it addresses the different testing requirements from manual to fully-automated operation.
-
Product
HIRF Testing
-
High Intensity Radiated Fields (HIRF) testing simulates high RF peak pulsed and average fields typical of radar environments and is integral to the certification of flight essential avionics systems. L3 Cincinnati Electronics (L3 CE) can perform HIRF testing from 400 MHz to 18 GHz (with traditional average field testing from 10 kHz to 40 GHz).
-
Product
Automatic Test
-
Test Systems of varied sizes and complexity are a specialty of EJC Systems. From concept through development, fabrication, and customer integration, the EJC Systems team brings experience and expertise to ensure every customer receives exactly what was requested.
-
Product
Package Test
-
WinWay’s commitment to technology, quality and service ensures our interface solutions go above and beyond to exceed your expectations. Our products and services have a proven track record of delivering customer success in semiconductor testing. The Company offers comprehensive test interface solutions ranging from wafer-level test, package-level test to thermal management.
-
Product
VME to USB 3.0/Ethernet/Optical Link Bridge
VX4718
-
The VX4718 is CAEN New Bridge with enhanced data rate and extended interfacing capabilities, thanks to the on-board MPSoC (including an ARM processor running Linux). The board is a VME Master which can be controlled by an external PC via USB 3.0 and Gigabit Ethernet connections.
-
Product
Content Testing
-
TestOrigen Software Testing Services Pvt Ltd.
Content Testing is basically known as an act of testing performed to know the usability of your content for the users. It is very important part of the internet based content, as the content testing is related to advertizing, selling of the product by attracting all types of users toward your product also.
-
Product
Biosafety Testing
-
Biological products derived from mammalian cell lines pose an inherent risk for the introduction of microbial or viral contaminants. In addition, the manufacturing process or product itself may introduce impurities that must be characterized.
-
Product
Test Software
Yelo Test Environment V5.0
-
The Yelo Test Environment (YTE) is an automated test environment developed by Yelo. Test sequences can be developed for multiple products and are tailored to customer needs and specifications. Flexibility in testing is a key benefit of the YTE and is provided to the user by allowing management of test sequence order. There is also the ability for the user to change the test limits or parameters for more or less stringent testing depending on requirements.
-
Product
Leak Testing
-
Leak testing is a non-destructive method to verify the presence of a leak in a component or device.It is implemented as a control methodology for monitoring production process and product quality control. Leak tests are used to find out possible leaks due to non-suitable material (porosity, blowholes, cracks), or in the machining process to find out machining errors or defective parts, and ultimately in assembly, to find out missing or defective gaskets, wrong positioning or assembly. The presence of a leakage could jeopardize the correct functioning of the component, device or its life span, and can also be potentially dangerous for the environment and the safety of its user.
-
Product
Ozone Test
-
Ozone is an extremely reactive form of oxygen occurring around electrical discharges. It is also present in the atmosphere, but in small quantities. Ozone testing is performed to determine the effect on materials such as rubber, plastics, etc, which are susceptible to ozone-induced degradation.
-
Product
Optical Gas Imaging Camera
EyeCGas CO
-
Opgal Optronic Industries Ltd.
EyeCGas CO is a handheld OGI camera for CO gas leak detection. With this camera you can safely and remotely detect and locate carbon monoxide as well as other harmful gases emissions. It is also the only OGI camera that is certified for ATEX zone 2 and UL class I Div II, hazardous environments. The EyeCGas CO allows for routine and on-demand inspections in the steel manufacturing operations and other industries where CO emissions need to be closely monitored. With EyeCGas CO, Opgal helps you detect and repair toxic gas leaks inside the facility, whether in vent stacks or pipes, allowing video and audio recording while maintaining safety. Whether these toxic gases are part of the manufacturing process, or a byproduct of the production line, EyeCGas CO helps increasing safety and protect the environment.
-
Product
Test Cables
-
Test cables for tone generators, butt sets, oscilloscopes, digital multi-meters (DMM), and other test equipment that uses specialized connectors like Bed of Nails alligator clips, RJ11, sheathed banana plugs, etc. Our cables are similar and replaces genuine manufacturer cables from Fluke, Harris, Tektronix, HP, JDSU etc.
-
-
Product
Optical Isolators
-
Thorlabs manufactures a wide selection of narrowband and broadband free-space optical isolators (Faraday isolators) that operate in spectral ranges from 365 nm to 9.80 µm, including high-power options, as well as fiber isolators designed for wavelength ranges from 650 to 2010 nm for polarization-independent versions and 770 nm to 2010 nm for polarization-dependent versions. For customers whose needs are not met by our stock selection, we offer a custom isolator service that can combine the best features across our entire isolator family. The Optical Isolator Selection Guide displays wavelength ranges and isolator types for all stocked isolators.
-
Product
Testing solutions
-
From Manual Testing, to test automation Ideabytes Inc is a one stop shop for all testing needs. Among the specialities Model Based Testing that changes the approach to testing reducing cost and catching faults early. With our methodologies, automated test cases are ready just as the developers are releasing their code. Contact us for a free consultation!
-
Product
Reticles, Optical Slits, Optical Apertures
-
With over 30 years of experience in the manufacturing of high precision Reticles, Slits, Apertures, and Pinholes, APPLIED IMAGE has gained a reputation for delivering precise and accurate parts. We have supplied thousands of these parts to be used in Day/Night Sights, Binoculars, Targeting Systems, Telescopes, Tank Sights, Microscopes, and many other Bore-Sight devices.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode
40-850A-314-M50
-
The 40/42-850A-314-M50 is a PXI/PXIe 4-channel multiplexer with MU (mini SC) connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Mini Fiber Optic Receiver
MX555 series
-
The Maxcom MX555 series optical receivers are versatile, low-cost and compact optical receivers are versatile, low-cost and compact optical receivers for use in HFC fiber applications.
-
Product
Rolling Seal 4 Optical Connector
RS4
-
- GAF/ELI enhances mating efficiency and eliminates potential for shell damage while offering positive latch indication.- Longer, contoured cable end lead-in bushing enhances fine alignment of connector halves during the mating sequence.- Reduced channel count to align with more efficient field architectures.
-
Product
ARINC-429 Module
M4K429RTx
-
The M4K429RTx is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 4000 family of carrier boards. The module supports up to ten ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word.
-
Product
Test & Measuring
-
Messung Electrical Engineering
Electronics manufacturing, testing and quality control need test and measuring equipment and ergonomic environments that are flexible, versatile and safe. Hence we bring the future of modern workplace systems for R&D labs, calibration centres, training and didactic centres, electronic assembly & testing, spread across the Indian electronic industry. Our innovative, modular & customised laboratory furniture systems, and intelligent test & measurement solutions are designed to improve efficiency while offering user comfort.
-
Product
Magnetic-Inductive Testing
MAGNATEST® Product Family
-
Foerster Instruments, Incorporated
The MAGNATEST product family is used for the non-destructive testing of metallic materials for magnetic and/or electrical properties. The test instruments are used in the automotive and aviation sectors as well as in the production of semi-finished products. The focus is on testing components relevant to safety such as brake discs, or ball pins and functional components such as camshafts and drive shafts, pivots and piston pins. Typical test tasks include hardness checks, material differentiation and sorting. MAGNATEST can also be used for the automatic testing for the geometric properties of all metallic series components. The high-performance amplifier installed in MAGNATEST test instruments makes it possible to analyze harmonics, which guarantees an extremely reliable and precise repetition, even when impacted by perturbations.
-
Product
Optical Sensors
-
Broadcom offers a wide range of optical sensors solutions including ambient light, RGB color, proximity and gesture sensors for a broad range of applications including:*Mobile / Computing - smart phone, tablet, laptop, gaming mouse, printer*Consumer Electronics – TV displays, handheld game console, digital camera*Lightings – Industrial / commercial lightings, residential lightings, outdoor street lightings*Automotive – Instrument panel illumination*Medical Diagnostic Equipment*Industrial Instrument*Contactless switches*White Goods*Sanitary Products*Health / Fitness Products
