-
product
HS1760/MIL-STD-1760E XMC Network Interface Controller
XMC-1760-NIC-FP
Avionics Interface Technologies
Configuration Variants available: XMC-HS1760-NCNT: One NC Node and One NT Node, XMC-HS1760-NCNC: Two NC Nodes, XMC-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
product
USB I2C Adapter
MS (Master & Slave)
*Plug & Play*No additional driver necessary*HID device drivers are included in major operating systems*Open interface description enables communication without a DLL
-
product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
PCI Express Ultra-fast Data Acquisition Add-In Cards
Ultraview's PCIe series of data acquisition add-in cards are complete A/D systems on a single PCIe add-in card. These boards incorporate up to 8GB of on-board RAM with up to 7GB/sec on Kintex 7 (up to 1.4GB/sec on Virtex 5) typical PCIe bus transfer rates enabling full-rate acquisition for long durations. All boards in the PCIe series are supported with the same user software allowing users to select the bit resolution and acquisition rate appropriate for a given application and then easily re-use the same software on a different part. Included with each card are graphical waveform viewers, example user software with source code included, and device drivers for Linux and Windows. The example software is intended to allow users to quickly prototype and develop their applications.
-
product
Industrial Ethernet Embedded Switches
ADI’s portfolio of embedded Real Time Ethernet Switch are ideal solution for adding Industrial Ethernet connectivity to any field device or controller application. Designed for scalable and flexible system development, they support all major Industrial Ethernet Protocols while also providing the ability to future-proof for many Time Sensitive Networking (TSN) features, for the IEC/IEEE 60802 industrial profile. They interface easily with any host processor including any ARM® CPU utilizing the protocol specific device drivers provided by ADI. This provides the flexible system partitioning enabling the selection of processor that best fits your application requirements. It also provides the freedom to utilize any vendors protocol stack.
-
product
2-Phase Stepper Drives Based On EtherCAT Field Bus
Nu-Step DA Series
The ADLINK Nu-Step DA Series is a stepper driver based on the EtherCAT bus featuring a 32-bit ARM processor and advanced variable current and frequency conversion technology. The driver generates less heat and motor vibration for more stable operation. It not only supports the standard EtherCAT specification, but also supports table comparison triggers for automated optical inspection (AOI) and linear comparison triggers for line scanning.
-
product
PXI-2567 , 64-Channel PXI Relay Driver Module
778572-67
64-Channel PXI Relay Driver Module—The PXI‑2567 is an external relay driver that works with internal or external power sources. The PXI‑2567 allows you to control relays when the current and voltage requirements for those relays exceed the capabilities found in existing relay modules or for relays embedded in a test system. The PXI‑2567 includes overcurrent, overvoltage, and flyback protection to ensure long-life operation. The PXI‑2567 can also drive small DC motors or other inductive relay coils.
-
product
ARINC 429 Test & Simulation Interface for VME
VME-429
Avionics Interface Technologies
4, 8, 16, 32, or 64 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full Error Injection & Detection - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application interface supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME - Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
product
Professional Software USB Protocol Analyzer
USBlyzer
USBlyzer is an easy to use Professional Software USB Protocol Analyzer for Windows.Universal Serial Bus (USB) protocol is very complex. So the USB support software present in Microsoft® Windows® operating system family is also complex and provides a layered architecture where the system-supplied and vendor-supplied user- and kernel-mode components can be involved in communications over USB. Transactions performed over the USB are initiated by the user applications which communicate with the operating system by calling Windows API functions which in turn interact with appropriate device drivers providing access to a USB device through standard and vendor-specific interfaces.What do you do when you want to know what is going on inside the Windows USB subsystem? What USB drivers are used to connect various peripheral USB devices to a computer? What I/O requests, support routines, structures, and interfaces the core components of the Windows USB architecture use to communicate with the USB devices? What you need is a Software USB Protocol Analyzer.Analyze and Realize USB Protocol:USBlyzer is an easy to use Professional Software USB Protocol Analyzer for Windows, which provides a complete yet simple to understand view for monitoring and analyzing USB Host Controllers, USB Hubs and USB Devices activity.
-
product
PXI Relay Driver Module
The PXI Relay Driver Module controls up to 64 external relays with up to 50 VDC or 600 mA per channel drive capacity when using an external power supply. Modules can drive small DC motors or other inductive relay coils, and they include overcurrent, overvoltage, and flyback protection to ensure long operation. The PXI Relay Driver Module allows you to build custom switch configurations while using the standard IVIcompliant NISWITCH driver software.
-
product
Laser Drivers
Analog Devices laser diode driver ICs work with Fabry-Perot, DFB, and VCSELs, and the ICs support continuous mode data rates from 50 Mbps to 11.3 Gbps.
-
product
USB Analyzer
USB protocol Analyzer is an easy to use USB Data Monitor for Windows. It offers simple, yet complete view for monitoring and analyzing activity of USB devices. USB Traffic Analyzer can intercept, record, display, and analyze incoming or outgoing data between any USB device plugged in your computer and applications. USB device analyzer can be successfully used in development of your applications, USB device drivers or hardware. It is your essential platform for efficient coding, testing, and optimization.
-
-
product
SpaceWire LabVIEW Driver VISA
137
STAR-Dundee's SpaceWire LabVIEW VISA driver has been implemented as a native LabVIEW driver, providing support for the STAR-Dundee PCI family of devices. Software written to control these devices may be deployed on any hardware platform that supports cPCI/PCI and NI-VISA, including both Windows based hosts and LabVIEW Real-Time targets, without requiring modifications to source code. The software is provided as LabVIEW source with password protected block diagrams, allowing users to compile for any target.
-
product
MAPS Core
An all-in-one core package includes the ADLINK products’ driver, device management utility-ACE and, PXI configuration setting utility
-
product
Isolated Gate Drivers
Analog Devices’ isolated gate driver portfolio offers designers performance and reliability advantages over designs utilizing optocouplers or pulse transformers. Utilizing ADI’s proven iCoupler® technology, the isolated gate driver family offers the advantage of a maximum propagation delay of 50 ns, less than 5 ns channel-to-channel matching, a 50-year lifetime for 400 V rms working voltage and galvanic isolation in a single package.
-
product
MIL-STD-1553 PMC Interface Module
PMC-1553
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - 3.3v PMC (with 5V Tolerant I/O), 64-bit 33/66MHz - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
MIL-STD-1553 Test & Simulation Instrument for VXI
VXI-1553
Avionics Interface Technologies
Dual redundant, multi stream configurations availableSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Real-Time recording and physical bus replayANSI Application interface supporting C, C++, C#, and .NET development - VISA based VXI “Plug & Play’ Device driver provided
-
product
MIL-STD-1553 Test & Simulation Interface for VME
VME-1553
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
product
NI Software Suites
NI software suites aggregate the most popular LabVIEW add-ons and other application software typically combined with LabVIEW and other development environments to help you build test, design, and control applications. Each suite, excluding the Multi-IDE Bundle and the Software Platform Bundle, also includes one year of unlimited access to professional training and certification.The suites come with related NI device drivers and are shipped on USB 3.0 media to speed up your installation.The NI Automated Test Software Suite combines LabVIEW, LabWindows/CVI, and Measurement Studio with the TestStand ready-to-run, customizable test executive and the Switch Executive intelligent switch management and routing application to help you build manufacturing or production test systems.The NI Embedded Control and Monitoring Software Suite features LabVIEW and the recommended add-ons specifically for building embedded control and monitoring systems on NI reconfigurable I/O (RIO) hardware. The LabVIEW FPGA Module extends the LabVIEW graphical development platform to target FPGAs on NI RIO hardware, and the LabVIEW Real-Time Module builds on LabVIEW to deliver a programming environment for creating reliable, deterministic, and stand-alone embedded systems.The NI HIL and Real-Time Test Software Suite combines LabVIEW with VeriStand, a configuration-based software environment for efficiently creating real-time test applications. It also includes the LabVIEW Control Design and Simulation, LabVIEW Real-Time, and LabVIEW FPGA modules.To learn more about each suite, use the navigation options on the left side of the page.The mark LabWindows is used under a license from Microsoft Corporation. Windows is a registered trademark of Microsoft Corporation in the United States and other countries.
-
product
Ethernet to Modbus RTU Interface
Model 9099
* Use Modbus TCP/IP, VXI-11, or Raw Sockets (Telnet) or to control Modbus RTU slave devices.* No special driver required which eliminates driver problems.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Interfaces with PLCs or any Modbus TCP/IP Controller.* Fully VXI-11 compliant.* Works with Agilent, NI and Kikisui VISA libraries.* Internal webserver with sample Modbus device control pages for Watlow F4, F4T and EZ-Zone Controllers.* Network connectivity eliminates GPIB Bus Extension problems.* Allows multiple users to access the Modbus network or devices.* 9099 is a 2x to 5x faster than the 8099 and includes a new Modbus device control page.
-
product
Fibre Channel Simulyzer™ Products
Avionics Interface Technologies
Our Fibre Channel products support most popular avionics Upper Layer protocols including FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All AIT Fibre Channel modules utilize multiple processors with large onboard RAM. An onboard processor runs the driver software, minimizing host CPU interaction, enabling autonomous operation with minimal interaction during time-critical applications.The Fibre Channel products use our Simulyzer™ technology that enables the hardware to simultaneously perform Fibre Channel data generation and Fibre Channel monitoring on the same physical board. The Fibre Channel test products include full-function device driver software for the most popular operating systems, an application interface supporting development environments, as well as a comprehensive set of source code examples.
-
-
product
Drivers / Controllers
The LED Driver/Controllers incorporate fully integrated power solutions. Digital drivers and controllers provide programmable, fully integrated power solutions with fast response times.
-
product
Developers' Toolkits
If you are a hardware developer, using RapidDriver Explorer with just a couple of clicks, you can easily start testing and debugging your USB, ISA, PCI or Parallel Port device. You do not have to perform any additional steps - everything is already done!If you are a software developer, you can write your own application with the help of RapidDriver Developer, TVicHW32 or TVicPort without writing a device driver and being a DDK expert - we have already built-in generic device drivers for you! Our toolkits include many test examples on direct port i/o access, interrupt handling, physical memory access, reading specific hardware registers and USB pipes to help you getting started. We also allow redistribution of drivers and DLL's as part of your software without having to pay royalties.For the software developers, we also offer an option to purchase the drivers and DLL source code. The source code can be directly edited and compiled with MS Visual C/C++ or with the DDK "build" utility.Not sure what product to choose? Compare them by features or contact us.
-
product
Board Drivers
9450-DRV
IOWorks board drivers are Abaco Systems' IOWorks data acquisition and control (DAQC) software driver. It is a hardware and operating system-independent driver designed to support the widest variety of I/O in the industry. The driver operates with many operating systems such as Windows NT/Windows 2000, QNX, VxWorks, and Linux, and delivers high performance and flexibility across multiple platforms such as CompactPCI, VME and PCI.
-
product
ARINC 429 PXI Express Test & Simulation Instrument
PXIe-C429
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Laser Diode Driver
Fibotec offers special laser diode drivers, especially versions that accommodate laser diodes via integrated terminal bases. Two standard products for different applications accommodate laser diodes in butterfly packages with up to 2 A forward current. The "Pump Laser Pinout" is standard. The configuration for "Signal Laser" is available on request.
-
product
LED/IGBT Driver
SiC/GaN
Mornsun Guangzhou Science & Technology
MORNSUN offers high quality IGBT driver, LED driver and driver power module for IGBT driver and SiC/GaN gate driver, which feature a compact design, are energy-efficient and robust with high quality at an affordable price. Especially MORNSUN LED driver is a step-down constant current source for driving high-power LED providing high efficiency, wide input voltage range, high temperature working capacity and complete functions. All of these driver power modules are applicable for multiple commercial and industrial applications.
-
product
Piezo Drivers
Use Trek high voltage amplifiers to drive piezoelectric elements and piezoelectric (ferroelectric) material poling.
