-
product
Dynatrol® Level Switch for Bulk Solids
CL-10DJ-7
Dynatrol® CL-10DJ-7 Vibrating Level Switch is designed for high-, intermediate- or low-point level detection of bulk solids. The CL-10DJ-7 is typically used with bulk solids in the density range of 60+ lbs/ft3.
-
product
Flow Switches
Not susceptible to contamination and can be oriented in any pipe configuration make these flow switches for liquid or air maintenance free and reliable. Mechanical and electronic designs available
-
product
Network Switches
Our switch fabric modules provide full service switching through hardware accelerating ASICs from leading device makers including Mellanox or may be software defined for upgradability. These high bandwidth switches include system management capabilities including full compliance with VITA 46.11.
-
product
Repair of Solid State Switch, P/N 60-SS480
Solid State Switch P/N 60-SS480Input: 480 VAC, 3PH, 60 HzOutput:480 VAC, 3 PH, 60 HzControl Voltage: 120 VAC, 1 PH, 60 Hz
-
product
Programmable Switching DC Power Supply
The SPS5000X-Series is a programmable Switching DC Power supply series that provides a wide range of output power using single-channel and multi-channel output configurations coupled with constant power capability. The series of power supplies includes sixteen models with voltages to 160 VDC and power to 1080 W. The SPS5000X supplies can be connected in series (2 units) or in parallel (3 units) to meet the requirements of 0~320V and 0~270A, with a maximum combined power of 3240W.
-
product
Switching Unit
ZET 454
The ZET 454 switching unit is intended for serial switching of 72 circuits of ZET 452 control devices to one of the sixteen sockets. The ZET 452 electric circuits control device is connected to a socket on the ZET 454 switching unit front panel. On the front panel of ZET 454 there also are sockets for tested device circuits connection, which is performed using the adapter harnesses.
-
product
Vibrating Level Switch
TF 100 Series
TF-100 Series is a vibrating level switch with TF-L relay output and TF-P transistor output or with TF-T current output.This level switch is designed for reliable indication of clean liquids and light slurries. It is available with Relay, Current, and PNP outputs that can be set to indicate alarm on either high level for spill prevention, or low level for run-dry protection.
-
product
RF Switches
An electronic component that routes high-frequency signals between different paths.
-
product
Flight Test Switches
Curtiss-Wright Defense Solutions
Our compact, deterministic flight test switches have been qualified to reliably deliver high-speed, real-time data with a wide temperature operation ranging from -40 to 85°C. Their rapid boot-up capability minimizes data loss from power outages, while their flexible forwarding and filtering configurations can send what is required to multiple destinations for real-time monitoring, recording, and transmission.
-
product
RF Switch Matrices
For applications involving the test and measurement of multiple RF components, Teledyne Coax offers Custom Switch Matrix solutions to integrate multiple switches, along with additional components including filters, mixers, and attenuators, as required. These Custom Switch Matrix units can contain SPDT, Transfer, or Multi-Throw Switches in either Multiple Input Multiple Output (MIMO) or Multiplexer (MUX) configurations.
-
product
Coaxial Transfer Switch, DC to 26.5 GHz
L7222C
These switches are ideal for manufacturing test engineers working on system integration. Use the Keysight L7222C 4-port coaxial transfer switch in a variety of applications such as a drop-out switch, switching two inputs and two outputs, or signal reversal.
-
product
Explosion-Proof Differential Pressure Switch
1950G
The Model 1950G Explosion-Proof Switch combines the best features of the popular Dwyer Series 1950 Pressure Switch with the benefit of natural gas compatibility. Units are rain-tight for outdoor installations, and are UL listed for use in Class I, Groups A, B, C, & D; Class II, Groups E, F, & G and Class III atmospheres, ATEX for EExd IIB & Hydrogen T6, and CSA & FM approved for Class I, Div. 1, Groups B, C, D; Class II, Div. 1, Groups E, F, G and Class III atmospheres
-
product
Dynatrol® Level Switch for Bulk Solids
CL-10DJ
The Dynatrol® CL-10DJ Vibrating Level Switch is designed for high-, intermediate- or low-point level detection of bulk solids. The CL-10DJ is typically used with bulk solids in the density range of 15-60 lbs/ft3.
-
product
PXI Dual 32x4 Matrix 1-Pole Switching
40-534A-021
Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109 operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by daisy chaining the common signals from multiple PXI modules.
-
product
Optical Switches
Fast and reliable optical switches to streamline your test procedures. Can be customized with a wide range of switch configurations, fiber types and connectors.
-
product
Pressure Switches
Pressure switches are built for industrial gas and compatible low-viscosity fluid applications. These pressure-operated switches are ideal for uses demanding a rugged, robust design. Environmental protection is provided by a high-grade IP67 (NEMA 6) enclosure, and the internal design provides excellent resistance to shock and vibration. Both the KAS and KPS Series feature SPDT switches with a DC contact rating of 125V, 12W. The KAS Series pressure switch has an AC contact rating of 250V, 0.1A inductive load. The KPS Series pressure switch has an AC contact rating of 440V, 6A inductive load and 440V, 10A resistive load. Many conventional, as well as some unconventional, requirements for outdoor and indoor use are covered by KOBOLD KAS and KPS Series pressure switches.
-
product
32-Ch SPDT 5A-240VAC 24VDC Switching
YAV90132
32 relays, 5A 28 SPDT relays, 5A Mux. 1 a 4 relays CAN Control or Ethernet (with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
PXI Single 64x4 Matrix 2-Pole Switching
40-533A-022
Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109 operations to give maximum switching confidence with long life and stable contact resistance.
-
product
PXI Optical Switch
The PXI Optical Switch is available in many different switching configurations for customized optical switching. It offers both single-mode and multimode fiber options that can support switching of very small wavelength signals. The switch provides either SC/PC, FC/PC, SC/APC, or FC/APC fiber-optic connectors. You can use the PXI Optical Switch for repeatable, low-loss switching.
-
product
Industrial Ethernet Switches
Rugged network devices built to operate reliably in harsh factory environments (extreme temps, shock, vibration) by connecting machinery like sensors, cameras, and PLCs, providing robust, high-speed data transfer.
-
product
Switches
When you choose Sensata switches, you gain a double advantage - extremely high quality devices plus our collaborative design process.
-
product
High Density Switches
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
-
product
Cutting Tool Breakage Detection Switch
TLPS/MTLPS/UTLPS
An air sensor that detects damage and damage to drills and taps in metal processing lines even when rotating.For the detection nozzle, a dedicated nozzle unit that matches the cutting tool is available.We also respond to use in adverse environments, which is one of the features of the air sensor.
-
product
Switch Filter Bank
Corech Microwave’s Switch Filter Bank frequency covers DC to 50GHz, featured with multi-channels (4 to 8 channels), high power handling, and fast switching options. Pin Diode Based Switched Filter Banks provide the highest level of signal isolation, higher operating power levels, and lower insertion loss and achieve switching speeds of < 40 nanoseconds.
-
product
High 1.80 (51.00) - 12.60 (357.00) Switch Probe
TSP138-F300-3
Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 20Test Center (mil): 138Test Center (mm): 3.50Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,760Overall Length (mm): 44.70Switch Point (mil): 67Switch Point (mm): 1.70
-
product
Switch
TOE 9261
Toellner Electronic Instrumente GmbH
Input voltage 60 V, Output current up to 100 A, Rise / fall time < 500 ns, Short-circuit-proof, Switchable discharge of load circuit, Interruption in supply and ground lines up to 100 A, Switchable buffering of input circuit, 4 signal line switches, Control with any signal generators (TTL level)
-
product
RF Switch Matrix
Switch Matrices are offered in Blocking, Non-Blocking, and Super Non-Blocking configurations in mechanical housing packages of 1U-10U. Completely customizable control (USB, 10/100 Base-T) and expandable in blocks of 8 by 8 and 64 by 64 in a single unit, multiple units up to 256 by 256.
-
product
TMR Switch Sensors
MultiDimension Technology Co.,Ltd.
A digital unipolar magnetic switch that integrates TMR and CMOS technology in order to provide a magnetically triggered digital switch with high sensitivity, high speed, and ultra-low power consumption. It is designed for use in applications that are both power-critical and performance-demanding. It contains a push-pull half-bridge TMR magnetic sensor and CMOS signal processing circuitry within the same package, including an on-chip TMR voltage generator for precise magnetic sensing.
-
product
6U VPX 1/10 GbE Switch
ComEth4341e
The ComEth 4341e is a 6U VPX 1/10 gigabit Ethernet switch for use in high-computing defense and industrial applications. It supersedes the ComEth4341a Ethernet switch and adds 1 or 10 gigabit Ethernet connections via 4 front SFP+ connectors.
-
product
Test Switches
Series FT
An industry standard for CT & VT isolationfor instrument transformer and connected device testing.Up to 10 poles; Numerous configurations availableTypically mounted on switchgear and relay panels10 pole test plug available; UL and cUL recognized.
