-
Product
Test Receiver
NTR GNSS
-
Our primary objective is to provide a high performance and fully flexible test receiver for all types of GNSS systems. Thus, the NTR fully supports all existing navigation systems. The signal processing is fully flexible. The high performance correlation engine with up to 80 channels is implemented in a powerful set of FPGAs. Signal acquisition and tracking are realized on a high performance embedded ARM Cortex A8.Supporting up to 4 L-band frequencies in parallel, the NTR GNSS test receiver supports all current GNSS transmission frequencies. Due to its plug-in design, the RF front-end can easily be customized for special filtering and other frequencies.
-
Product
Test Cells
-
LaplaCells provide a facility for the rapid and efficient testing of the EMC compliance of products. These cells offer a calibrated and screened environment in which radiated emissions can be measured and immunity to RF radiation can be tested. They exceed the requirements of IEC61000-4-20, thus affording compliant testing to IEC61000-4-3 and pre-compliance testing for radiated emission testing. The Cells are a modified form of GTEM cell, using a balanced dual septum design which maximises EUT volume for a given external size of cell, and dramatically improves field linearity. The EUT volume is fully lined in structural polycarbonate capable of supporting heavy products and access is via a large, full height door at the end of the cell. Adjacent to the door is the I/O filter compartment which can be customised to suit the users requirements. USB, RS232, Parallel, Ethernet, co-ax and other product specific filters can be added at time of ordering.
-
Product
Small-fiber Test
Q-Sense
-
Q-Sense offers a scientifically validated measure of warm, cooland heat-pain thermal sensory thresholds, all clinically usefuldeterminants in the evaluation of neuropathic pain, diabeticneuropathy, chemotherapeutic and other small-fiber neuropathies.
-
Product
Assembly & Testing
-
All components and subassemblies receive the highest attention to detail and workmanship, ensuring your satisfaction. From the initial design phase through to the final assembly, we are committed to producing the best possible products for our customers. Our team of skilled builders and assemblers take pride in their work and are committed to producing the best possible products.We thoroughly test and inspect all of our products before they leave our facility, and we stand behind their quality and workmanship. We are confident that you will be satisfied with your purchase, and we ensure that every product meets our high standards of quality control before it is shipped.If you have any concerns about the quality of your product, please don't hesitate to let us know. We are always happy to address any issues and ensure your complete satisfaction with our products.
-
-
Product
Electrical Testing
-
Accolade Engineering Solutions
Accolade Engineering Solutions offers a variety of Electrical Testing Applications services. Contact us today to discuss your testing needs with someone who can provide you with the expert knowledge to determine the right testing solution for you.
-
Product
Telecom/NEBS Testing
-
Eurofins E&E North America’s extensive capabilities in telecommunications include testing, compliance assistance & design reviews, application preparation and agency liaison. Eurofins tests products for compliance to U.S., Canadian, and international standards for telecom devices, from NEBS equipment to consumer products such as DSL modems.
-
Product
Load Testing
OctoPerf
-
Use auto-correlations rules and frameworks as well as test validation to quickly create virtual users.
-
Product
Water Testing
-
Trialon routinely test products for the automotive, military, medical, aerospace, heavy truck and customer markets in our facilities in Michigan and Indiana.
-
Product
Test Compliance
MX CTS Series
-
AMETEK Programmable Power, Inc.
A growing number of electronic products manufactured today have to meet international regulatory requirements for emissions and immunity. This is particularly true for products sold in the European community as well as a growing list of countries in the Far East. The California Instruments MXCTS System provides a cost-effective test solution aimed at verifying higher power product compliance to a number of AC and DC related harmonized test standards. The MXCTS system offers many of the same features and capabilities of the California Instruments CTS Series product line already in use at many EMC labs around the world.
-
Product
In-Circuit Testing
-
If you are looking for in-circuit test applications, equipment or advice, our experienced engineers can help you. Whatever your fixturing requirements or special software features, our long history of work in this field means that we have probably seen and done it before.
-
Product
Sound Testing
SP series
-
Are ideal for on-site measurements in accordance with the noise at work legislation for industrial and office environments.
-
Product
Test Automation System for Durability Testing
STARS MATS
-
STARS MATS is a Mileage Accumulation Test System application available with the STARS Automation platform for chassis dynamometer. The application provides test execution, equipment control, refueling, and vehicle state monitoring to perform long endurance test without the necessity of continuous staff presence. Its flexible design offers a wide range a customization, and it addresses the different testing requirements from manual to fully-automated operation.
-
Product
Test Equipment
Digital Multimeter
-
*True RMS*2,000 counts*Auto/manual range*Auto power off (APO): 5 mins approx.*Over range display*Non-contact AC voltage detection (NCV) (with audible sound and visible indication)*Auto/manual AC/DC voltage measurement (600V AC/750V DC)*Auto/manual resistor measurement: 0-20MΩ (approximate)*Continuity check: approximate <50Ω buzzer sounds*Diode check*Auto/manual AC/DC current measurement (mA/mA/10A)
-
Product
Test Chambers
-
The left-hand axis scales the level of the 100 measurements and the right-hand axis displays the uncertainty to a statistical confidence level of 95%; proving the repeatability is better than +/-0.25dB between the measured values. Guaranteeing repeatability, accuracy and correlation across Lab’s, across Production lines and across the World
-
Product
Test Sockets
Non Standard
-
Chances are good Ardent can help you with that. We can adapt our technology to just about any package, device or module. Small volumes of custom sockets for higher bandwidth applications are a niche all in their own, and our engineering team has many years of experience designing custom sockets for all kinds of applications.
-
Product
Test Contactor
RF Scrub
-
RF Scrub™ Test Contactor’s innovative design combines an extremely short signal path (0.90mm test height) with high wear resistance pins that can operate in a wide temperature range.The RF Scrub Test Contactor’s long-life, elastomer free design and easy field maintainability makes it an optimal solution for testing of high-performance devices.The RF Scrub design minimizes load board wear and with the unique pin base material and plating, the cleaning intervals can last up to 100,000 cycles.
-
Product
Test System
ETS788
-
The 55/110 MHz ETS788 system boasts the same small footprint and cool quiet CMOS architecture as our ETS780 but with the new high-performance precision components of our Griffin series. This powerful member of the HiLevel family takes advantage of all of the tried and true features that have served users so successfully to date. Learn why the ETS788 is the perfect cost-effective solution for higher performance in Design Verification, Production and Failure Analysis.
-
Product
DHCP Tests
-
The Dynamic Host Configuration Protocol (DHCP) provides configuration parameters to Internet hosts. DHCP consists of two components: a protocol for delivering host-specific configuration parameters from a DHCP server to a host and a mechanism for allocation of network addresses to hosts. DHCP is built on a client-server model, where designated DHCP server hosts allocate network addresses and deliver configuration parameters to dynamically configured hosts. (Source: RFC 2131)
-
Product
Testing Services
-
Koehler Instrument Company, Inc.
A complete source for your testing solutions, Koehler offers a wide range of in-house testing services based on selected standard test methods. Our staff is comprised of technical experts and the best instrumentation for fast, accurate and reliable results. We specialize in all tests for which we offer instrumentation as well as additional test methods. You are invited to send us samples for testing and evaluation at any time. Please contact your Koehler representative for additional information.
-
Product
Test Studio
-
Automated testing has come of age with Progress® Telerik® Test Studio. With the industry's fastest test recorder, its patent-pending mixed element find logic makes tests more stable and reliable while keeping test maintenance to a minimum. Test Studio maximizes test coverage ensuring optimal app quality and addresses QA’s top challenges.
-
Product
Thermal Testing
-
A view of multiple testing stations for use in conducting Thermal Analysis on various materials. This is one of several areas assigned to various thermal tests. Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA), Thermomechanical Analysis (TMA), and Dynamic Mechanical Analysis (DMA)
-
Product
Test Chambers
-
Drug test chamber, ozone test chamber, plant grown chamber, salt spray test chamber, sand test chamber, temperature and humidity test chamber, UV test chamber, xenon test chamber
-
Product
Device Testing
-
The BTL Working Group (BTL-WG) has developed a test package which contains a set of testing procedures. These can be acquired and used by manufacturers to pre-test their products for BACnet compliance before they send their products to an RBTO (Recognized BACnet Testing Organization) for BTL Testing. The BTL Test Package is available on the test documentation page.
-
Product
Test Leads
-
PMK Mess- und Kommunikationstechnik GmbH
It is used to test and measure the current in a circuit. These are simple devices which are coated and colored to indicate positive and negative with the device connector on one end.
-
Product
Microwave Testing
140
-
The PICOPROBE® MODEL 140, a high performance microwave probe which incorporates a WR-8 waveguide with our patented coaxial design techniques, has inherent low loss and low dispersion characteristics.
-
Product
Conformance Testing
Clarinet-TTCN SS7 ETS
-
Protocol: ITU-T Q703 standard defines protocol for Signaling System No. 7 – Message transfer part IUT: SS7 Signaling Point - MTP2-ITUATS: Based on ITU-T Q781 (07/96) test descriptions.
-
Product
Test Services
-
Our services cover all aspects of test, from test plan generation; to hardware and software development; to validation, correlation, ramp and production. Our experts have deep experience in digital, memory, mixed-signal and RF applications. We also specialize in secured applications that require personalization/root of trust during backend production.
-
Product
Ultrasonic Testing
Pundit PL-200
-
The Pundit PL-200 is a best-in-class Ultrasonic pulse velocity (UPV) test instrument to examine the quality of concrete and other materials such as rock, wood and ceramics.
-
Product
Material Testing
-
Materials testing, measurement of the characteristics and behavior of such substances as metals, ceramics, or plastics under various conditions. The data thus obtained can be used in specifying the suitability of materials for various applications, building or aircraft construction, machinery, packaging etc.
