-
product
Digital Hardness tester
THL270
Pen type Leeb hardness tester Converts to all common hardness scales (HL.HV,HB,HRC,HRB,HRA,HS). The machine also include interface to connect with impact device C, DC, G, D+15, DL
-
product
AMIDA 3001XP Tester
AMIDA has introduced two new analog/mixed-signal and logic options in the AMIDA-3000 series in recent years—the AMIDA-3001XP and AMIDA-3KS test systems. Both reinforce the AMIDA-3000 series' ability to provide cost-optimized test solutions for a variety of consumer components in power management and mobile device components. The AMIDA-3000 series provides more than twice the number of analog channels of its modules per test system, thus greatly reducing the acquisition cost of each channel and more than doubling the number of analog channels in the entire test system. This results in a higher number of parallel tests and a higher level of capability for this system, as well as a lower and more cost-effective IC unit test cost for this tester. This series of test systems provides a powerful test combination with high-speed hardware and software integration. The built-in instant messaging protocol detection function of AMIDA-3001XP test machine not only simplifies the complexity and difficulty of test development, but also greatly shortens the test time by using its high-speed computing capability.
-
-
product
Antenna Position Tester
FTA
Fuzhou Fuguang Electronics Co., Ltd.
FTA series Antenna Position Tester is a convenient test instrument for planning, construction, maintenance and optimization of antenna system.
-
product
Battery Tester
IT5100 Series
IT5100 series is a series of battery internal resistance testers with high precision, high resolution and high speed. IT5100 adopts AC 4-terminal sensing, that means the tester can test internal resistance and voltage simultaneously with high precision. Resistance resolution is down to 0.1 μΩ, voltage resolution is 10 μV.
-
product
Pitot Static Tester
ADSE 643
The ADSE 643 caters fully for all aircraft types and the different electrical power supplies.It can be used for testing high performance civil and military aircraft, fixed and rotary wing.This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems.The ease of use and portability enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator.The test set is housed in an anodized metal and rugged case.An attached case contains the pressure hoses and electrical cables.
-
product
Concrete Tester & Surveyor
CTS-02V4
CTS-02V4 (Concrete Test and Surveyor) is a Non-destructive testing device for estimation of compressive strength of concrete. CTS estimates the compressive strength of concrete based on Mechanical Impedance Method by measuring a waveform of impact force with an accelerometer which mounted on the hammer unit.
-
product
Flow Leak Testers
If you need high-quality air flow testers, you’ve come to the right place. We carry equipment for mass flow and leak testing, laminar flow, and continuous flow. You have the option of choosing touch screen or standard digital. All our equipment is compact and includes high-performing, state-of-the-art technology. Begin testing your equipment with our premium-grade flow testing equipment. Explore our amazing selection of flow testing equipment.
-
product
Crush Tester 350
DRK113
Shandong Drick Instruments Co., Ltd.
DRK113 Crush Tester 350 is a high accuracy and intelligent instrument, designed according relevant standards. The advanced components, mating parts and micro-computer are logical structured, to ensure the property and appearance. The instrument have parameter testing, adjusting, LCD digital display, memory, printing function.
-
product
Battery Cell Tester
This Centre zero instruments help to read the voltage irrespective of polarity.
-
product
NBS Abrasion Tester
UI-FT40
NBS Abrasion Tester is used to test rubber abrasion resistance and to know material nbs abrasion index. NBS abrasion test is suitable for vulcanized rubber used for soles and heels of footwear. Unuo NBS Rubber Abrasion Tester is designed and applicable according to ASTM D1630. Here for More Abrasion Tester.
-
product
Static Soil Tester
GEO-probe
The complex is implemented on the basis of a portable computer and the CompactRIO control and measuring system. The software for recording and displaying measured signals and control of measuring equipment is developed on LabVIEW. The second modification of the measuring system includes, developed by our company, a miniature digital measuring module of a strain gage with a built-in ADC and inclinometer and a USB interface for connecting the digital measuring module of the probe to the computer.
-
product
HID Ballast Tester
WT2000-HID
• Input Parameters Measurement: 1) Test voltage, current, power, power factor, power line frequency, total harmonic and 0~50 harmonic 2) Range of voltage and current basic wave frequency: 45Hz~65Hz 3) Range of narrow frequency: 45Hz~5kHz 4) Range of wide frequency: 45Hz~1MHz
-
product
Hydrostatic Head Tester
TF163
TESTEX Testing Equipment Systems Ltd.
Hydrostatic Head Tester, used for determining the resistance of fabrics (canvas, coated fabrics, cover cloth, rainproof clothing fabrics, and geotextile materials) and films to water penetration under pressure while firmly clamped in the test rig of standard area.
-
product
Analogue IC Tester
SYSTEM 8 (AICT)
The SYSTEM 8 Analogue IC Tester is the answer to testing analogue devices. The key feature of the AICT is its ability to functionally test all common analogue ICs and discrete devices in circuit. It is also capable of testing all types of analogue and digital components by means of the well-known, power off V-I test technique. For users requiring only the latter function, please select the Analogue Test Station section.
-
product
Current Transformer Testers
Vanguard Instruments Company, Inc.
Performs CT excitation, current-ratio, polarity, and phase angle testsMeasures insulation resistance and winding resistance of the CT seconday windingsMeasures the CT's secondary burdenTest record header information including company, substation name, circuit ID, manufacturer, CT serial number, operator name, and test record-commentsBuilt-in 4.5-inch wide thermal printerPlot Multiple Saturation CurvesStores up to 128 CT test plans and 140 test records internallyUSB, Bluetooth, and USB Flash drive interface
-
product
Insulation Testers
Sanwa Electric Instrument Co., Ltd
Is a spot insulation test which uses an applied DC voltage (typically either 250Vdc, 500Vdc or 1,000Vdc for low voltage equipment <600V and 2,500Vdc and 5,000Vdc for high voltage equipment) to measure insulation resistance.
-
product
Low Voltage Harness Tester
CR
Test complex assemblies with thousands of points. The system supports guided assembly with on-screen connector images, guidance LEDs on the assembly board, and immediate graphical and audible feedback to catch errors as they occur.
-
product
Blanket Flammability Tester
TF316
TESTEX Testing Equipment Systems Ltd.
Blanket Flammability Tester, to determine the ignition resistance property of blanket fabrics and surface flame spread performance of fabric. A standardized flame is applied to the surface of specimen for a special time under controlled conditions, and burning, changing, or discoloration of a paper monitor is noted to classify flammability of tested fabric.
-
product
Bally Flexing Tester
TF116
TESTEX Testing Equipment Systems Ltd.
Bally flexing Tester is designed for flexing resistance test to be and ingor other types of failure at flexing creases. The machines applicable to all flexible materials,in particular leathers, artificial leather below thickness
-
product
Insulation Resistance Testers
UEi Test & Measurement Instruments
Measures the total resistance between any two points separated by electrical insulation.
-
product
Battery Conductance Tester
FST-8000
Foresight Electronics Co., Ltd.
Profsional battery conductance tester for Lead-acid stationary (wet, flooded, gel, AGM, VRLA) battery cells/blocks, to measure actual capacity and aging for UPS, telecom, industrial, vehicle, solar or other applications' small and large battery banks.Battery Conductance Tester is a portable digital measurement device for testing lead acid stationary batteries health and aging condition precisely within seconds.
-
product
High Voltage Tester
Aarohi Embedded Systems Pvt. Ltd
AAROHI make high voltage tester is specially designed to test induction & submersible motors with cutting edge technology.High Voltage Tester is manufactured as per the International set standards and regulations. This High Voltage Testers are available in AC and DC types and are used for testing HV cables after installation and repair for ensuring efficient performance. It also indicates voltage withstands level and current leakage level of the cable during the testing period.
-
product
Flexible AC/DC Current Tester
FCM-100
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Bending free flexible clamp sensor *Wide measuring ranges (AC/DC 0.001A～2500A)*Easy accessibility to the hard to clamp object*Big CT window (φ200mm)
-
product
Portable Appliance Tester
PAT-10
The innovative combination of small dimensions (full portability of the device) with advanced measuring systems allow to carry out fully automated measurements for electrical equipment, IEC cables and extension cords (including those with PRCD). The set of tests is performed with one click of START button. Configuration options of the meter allow you to modify the operation of the device, and thus, tailor it to the needs of the user. In situations, where it is necessary to perform simple and single measurement, without the need to do complex measurement procedure, Pat Sonel allow you to work in a single measurement mode of a given type (ie. Manual). All meters in this series (Pat) also allow you to make basic measurements without external power in emergency situations i.e. in the absence of the power one can easily run a simplified set of test in a battery mode. Small size, weight, and specially designed carrying case of the meter and accessories provide comfort and high mobility. Wireless communication with a printer enables organization of the working site without the hassle of unnecessary cables. Storage and integration of the results in PC software further extends the functionality of the instrument.
-
product
Hydrostatic Testers
Hydraulic Technology Inc. has been manufacturing hydrostatic test equipment to the U.S. Military, aerospace and industrial sectors for over 30 years. These hydrostatic test systems are used for both high pressure proof testing and burst hydrostatic testing. By simply connecting one of our hydrostatic test systems to a shop air supply, safe high pressure testing can be accomplished with hydrostatic test output pressures available up to 15,000 psi. Among other specifications, our hydrostatic testers meet the requirements of MIL-T-25456, A-A-52687 AND PD02LEEE07. In addition to U.S. Military stock listed hydrostatic testers, we manufacture both standard and custom hose proof test stands, portable hydrostatic testers, hydrostatic test chambers and ancillary equipment to fit individual customers’ needs as required. We can typically ship standard units within 24-72 hours, sooner if required.
-
product
Automotive Battery Testers
ELAK Battery Testers are high-rate discharge testers. These testers impose a load on the battery, which is equivalent to that drawn by the starter motor from the battery, while cranking the engine. The tester studies the drop in battery voltage & indicates the condition of the battery if it is capable of starting the engine or not.
-
product
Core Loss Testers
S30 and S30S Series
Stacks built with punched laminations can have a lot of quality issues. Even though the lamination material is tested in sheet format before any process, that alone is not sufficient to guarantee good quality stators. Wear and tear of the punch, bad welding, bad insulating coating in annealing add to the magnetic losses in the stator. It is always advisable to test the stator core in it's final format before winding to ensure good quality throughout the production batch.
-
product
Hook Probe Circuit Tester
TE6-0707
Hangzhou Tonny Electric & Tools Co., Ltd.
Used to locate hot circuits and troubleshoot primary circuits on all 6, 12 and 24 volt systems. Suitable for a broad range of household, car, trucks, boats, trailers, vans, motorcycles, industrial and commercial uses.. Convenient screwdriver-type handle. Heavy Duty probe. Heavy plastic handle and insulated ground clip. Testers light up to indicate testing result. Durably designed for a long service life. Lights for easy visibility. Heavy duty coil cord or straight cord (optional). Materials: plastic/metal
-
product
Incline Impact Tester
KRD100 series
KRD100 series incline impact tester simulates the ability of product packaging to resist shock damage in the actual environment, such as handling, stacking of shelves, sliding of motors, loading and unloading of locomotives, product transportation, etc. This machine can also be used as a common test equipment for scientific research institutions, colleges and universities, packaging technology test centers, packaging materials manufacturing plants, and foreign trade, transportation and other departments to conduct incline impact test.
