Inertial Measurement Units
combinations of precision gyroscopes, accelerometers, magnetometers, and pressure sensors measuring motion.
See Also: IMU
-
product
Vibration Measuring System
SmartVibro
There are many functions to express characteristics of vibration. However it is necessary for the conventional vibrometers that the same point is measured plural times switching objective functions one by one. SmartVibro which has a simultaneous measurement function can measure Acceleration, Velocity and Displacement simultaneously by just pressing the measurement start key one time. It can reduce the operating time and prevent miss-measurements. By switching the screen, VM-4424S・VM4424H can confirm Acceleration Envelope for bearing condition which enables small scars to be found easily.
-
product
RTD Measurement for CompactPCI
CPCI390
The CPCI390 has a 3U form factor and features six 2-, 3-, or 4-wire high-accuracy RTD measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued. The local DSP (TMS320C203) performs linearization, auto-calibration and alarm limit checking. Sensordata is available in °C, °F, K and Ohm. All inputs are optically isolated from the system.
-
product
Ventilation and Heating Unit
HD9906.51
The heating and ventilation unit is meant to be used with solar radiation sensors (pyranometer, pyrgeometer and radiometer) and can be used outdoor under any weather conditions.
-
product
3U cPCI Sensor Interface Unit
SIU31
NAI's SIU31 is a highly configurable rugged COTS system or subsystem ideally suited for military, industrial, and commercial applications that require high-density I/O, communications, Ethernet switching, and processing. The SIU31 uses one NAI field-proven, 3U cPCI board to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-to-Mission."
-
product
DC Measurements
Standard Windows sound cards do not respond to DC or frequencies lower than a few Hz. (See Why Sound Cards Block DC Signals below for explanation.)There are two general approaches to get true DC response from a standard sound card: Modify the card, or add an external circuit to convert the DC into an AC signal which can be easily measured by an unmodified card.
-
product
Dimensional Measurement Laboratory
As your partner, Trialon’s commitment is to provide accurate dimensional measurements. Our facility is equipped with technical expertise and equipment to provide reliable First Article Testing and 3rd Party Dimensional Measurement Services.
-
product
Measurement, Data Analysis, Visualization, Automation
Imc STUDIO
With imc STUDIO, you are ready to start your measurement in a few minutes. A clearly organized channel configuration list, extensive sorting and filtering functions, numerous assistants, built-in sensor management and support of TEDS are just some of the useful functions for achieving quick, intuitive system configuration.
-
product
Universal Measuring Device For Magnetic Fields
Teslameter M-Test MK4
The M-Test MK4 precisely detects and measures static or dynamic magnetic fields. The ~ 1 mm thick tangential probe allows precise, punctual measurements in hard-to-reach places, air gaps or on surfaces. The M-Test MK4 is particularly suitable for measuring permanent magnets or small ferromagnetic parts.
-
product
Concrete Measuring and Monitoring System
IQM-Meter
Designed specifically for monitoring and analyzing fresh concrete, the IQM Module is programmed with the required Equivalent Age of the concrete under test. Once this preset maturity number is reached, a visual indicator will flash continuously, providing an effective, automatic indication that the concrete has reached the desired level of maturity.
-
product
RF Test and Measurement Solutions
Signal GeneratorsSwitch MatricesProgrammable AttenuatorsControl ProductsSignal MeasurementModular Test SystemsCustom Test SystemsUser-Friendly Control Software
-
product
Portable heat flux sensor, with read-out unit
HF03 / LI19
Hukseflux Thermal Sensors B.V.
The HF03 is a heat flux sensor that can be used in mobile applications. It is combined with LI19, a high accuracy hand-held read-out unit that can be used both for mobile measurements and as an amplifier directly connected to a PC. The combination HF03 / LI19 is typically used to study heat flux levels around flares and fires, and to calibrate flare radiation monitors / flare heat flux sensors.
-
product
Unit Testing Mocking Solution for .NET
SmartRunner
SmartRunner will identify and run only the impacted tests, which means that you no longer waste time waiting for all your tests to run and you get super-fast feedback.
-
product
Automated Multi-Edge Measurement Device
EdgeMasterX
The EdgeMasterX is a fully automated cutting edge measurement device for production integrated quality assurance of inserts, drills, mills and other round tools. Specifically, the EdgeMasterX enables automated multi-edge measurement of tools. In a single measurement run, a complete series of user defined measurements at multiple edge positions can be achieved. All results are traceable, repeatable, and in a high vertical resolution.
-
-
product
Hall Effect Measurement system
HMS-3300
Magnetic flux density : 0.55Tesla (+/-0.03T)Gap distance between both round magnets : 26mm / Round magnet diameter : 50mmMeasurable temp : RT ~ 300℃(model# HT55T3). Resolution : 0.1℃(Model# HT55T5 : RT ~ 500℃)Both HT55T3 and HT55T5 are only capable of using with HMS-3000 main body.(Not compatible with HMS-5000 )- You can flow purge gas into small chamber and measure hall effect at the same time. Gas control valve can be installed as an option.
-
product
Universal 3D Measurement Software
Metrolog
Get a real performance accelerator for your 3D measuring devices and more.Not only does Metrolog X4 architecture benefit from current computer and OS technologies significantly increasing the performances and metrology software throughput, but it also simplifies your day-to-day measurement workflow.
-
product
Multi-interface Electronic Control Unit
The Mors Smitt CatEnergy control unit ECU is the most modular and scalable solution available on the market for all function using high voltage measurement. From Energy Measurement purpose to all essential train function, the CatEnergy ECU is the perfect compact system for all demanding application on existing and new build train.
-
product
X-Series Measurement Applications for Signal/Spectrum Analyzers
The X-Series applications are proven, ready-to-use measurements for signal analysis. Simplifying complex tasks and delivering repeatable results, the applications let you see and understand the performance of your cellular, wireless and aerospace/defense devices and designs.
-
product
CMM Contact Measurement (Probing)
A method of collecting single points relative to each other in small or large volumes. This information can then be used for evaluation, inspection, layout or basic geometric reverse engineering. For capturing localized or small volume information, digitizing or articulating arms are ideal. For larger volumetric projects, optical solutions like laser trackers and photogrammetry CMMs perform best.
-
product
Precision Source / Measure Unit (2 Ch, 100 FA)
B2902B
The Keysight B2902B precision source / measure unit (SMU) is a 2-channel, compact, and cost-effective benchtop SMU with the capability to source and measure both voltage and current. It easily measures current versus voltage (I/V) with high accuracy. The 4-quadrant source and measurement capabilities enable taking I/V measurements without configuring multiple instruments.
-
product
Emission Measurement Equipment
EPS Series
Nowadays, components mountings are getting dense accompanied with miniaturization of electronics equipments.Emission Measurement System "EPS series" are efficient tools to measure such radiation noise on PCB in normal office environments and visualize the noise strength on a PC display.
-
product
Compact Design Measurement System
Benchmark 450
The Benchmark's fixed bridge design separates the X and Y axis motions, allowing each to operate without any influence on the other. This arrangement provides the maximum mechanical integrity and accuracy in the stage motion. The bridge type design also makes loading and unloading of large parts more efficient, and helps to minimize the overall footprint of the system.
-
product
Non-contact Diameter Measurement
Precision measurement is our focus. Our laser and ultrasonic-based technologies provide non-contact diameter measurements for a wide range of materials. Our accurate suite of tools cover outside diameter (OD), ovality (eccentricity), wall thickness (coating thickness/material thickness), concentricity, inside diameter (ID), and more.
-
product
Voltage Regulator Testing Units
With the goal of providing the industry with the best products ahead of the curve, we continue to develop a complimentary line of Voltage Regulator Testing Units for laboratory and production testing.
-
product
Transmitters for Humidity Measurement
Our humidity and temperature measurement transmitters with either an interchangeable probe input, or a fixed / integrated probe provide high precision measurements with analogue or digital outputs for process monitoring and control.
-
product
Conductive Emission Measurement
Holland Shielding Systems B.V.
On site testing for exposure limits in working conditions to any international standard. This involve pacemakers and HSE Heath and safety executive, invitarisations worldwide.
-
product
Releaseit Shallow Water Deck Unit
Teledyne Benthos’ new Releaseit Deck Unit and dunking transducer enables communications and acoustic release functionality when used with any of Teledyne Benthos’ R-Series Acoustic releases deployed in shallow water environments. Designed with Teledyne Benthos’ proven engineering and reliability, Releaseit is a value-priced alternative deck unit allowing for basic coastal operations. When paired with our new R500 Shallow Water Acoustic Release, the combined system represents a lower-cost turn-key option for shallow water applications up to 500 m water depth.
-
product
Portable PD Acquisition Unit
AQUILA
Techimp AQUILA has been expressly designed to respond to all these needs being a robust and compact portable all-in-one PD detection station providing a full range of options ideal for on field applications. It can cope with the toughest outdoor conditions while taking measurements on any electrical asset. 15 years of service experience has been condensed in this unit integrating TECHIMP innovative PD detection technology with multiple connectivity (Wi-Fi, Fiber Optics, USB, Bluetooth) and power supply.
-
product
Measurement Accessories
Maximize both performance and convenience with a full range of accessories for Coherent meters, sensors, and beam diagnostics systems.
-
product
Torque Measurement Systems
Proper torque measurement is critical in many assembly operations. AIMCO provides expertise and measurement equipment for all three phases - before, during, and after assembly. Tool testing and capability studies can be easily performed in the tool crib or lab. Fine tuning of torque settings and process verification are achieved on the assembly line with rotary transducers. Use our complete line of electronic wrenches for final residual torque testing.
