Intelligent Electronic Device
a microprocessor that controls power equipment devices.
-
Product
Differential And I/Q Device Measurements
S95089B
-
The S95089B combines source-phase control of multiple internal or external sources with frequency-offset mode, enabling simplified test of I/Q modulators/converters, differential mixers, and harmonics or amplifiers.
-
Product
FD-11601, 8-Channel, ±10 V Powered-Sensor Voltage Input Device for FieldDAQ
786374-01
Voltage Input Module
The FD-11601 measures up to eight channels with a voltage input range of ±10 V. Each input channel supports TEDS and provides 24 V DC to power external-powered sensors without additional power supplies. The FD-11601 features 24-bit resolution, simultaneous sample rates up to 100 kS/s/ch, and channel-to-channel isolation. It is IP65/IP67 rated to be dust-tight and water-submersible, operates in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11601 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11601 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. The FD-11601 is ideal for test cell and outdoor environments.
-
Product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-50
Interface Module
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
Detectors and Associated Electronics
CdZnTe/CdTe
-
Baltic Scientific Instruments, Ltd
CdZnTe (CZT) is a room temperature semiconductor which allows to create X- and gamma-ray detectors with comparably high energy resolution and high count rate capability without cooling. Detectors performance allow to use CdZnTe detectors successfully in Nuclear Industry and Medicine, Safeguard and Homeland Security, many others industrial and laboratory applications.
-
Product
PDA Software Simplifies Ethernet Powered Device Testing
-
All PDA-600 Powered Device Analyzers come with productivity software including the PDA Interactive graphical user interface and the PowerShell PDA script automation development environment. Also included is an Windows binary API library to provide programming extensions to a variety of programming languages.
-
Product
USB-7856, Kintex-7 160T FPGA, 1 MS/s Multifunction Reconfigurable I/O Device
782916-01
Multifunction Reconfigurable I/O
Kintex-7 160T FPGA, 1 MS/s Multifunction Reconfigurable I/O Device - The USB‑7856 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7856 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
Product
Thermal Conductivity Measuring Device
TCM1001
-
In recent years, there has been a demand for small and thin electronic products such as mobile devices, and printed circuit boards are shifting to thin, multi-layered, and even modularized printed circuit boards. effect of bonding materials, that is, the ability to easily conduct heat, is emphasized, and testing equipment that evaluates thermal conductivity is required .As a business of our company, we have mainly manufactured and sold test equipment for solder wettability tests and solder bonding strength, but there was a need to urgently develop next-generation bonding material test equipment to replace these. Under these circumstances, we received a request from an academic research facility to manufacture a device that can measure the thermal conductivity of conductive adhesives under research and development, and we were able to obtain an opportunity to develop the device. We proceeded with the development based on these requirements .
-
Product
PCI-5412, 100 MS/s, 14-Bit Waveform Generator Device
779177-02
Waveform Generator
The PCI‑5412 can generate user-defined, arbitrary waveforms and standard functions, including sine, square, triangle, and ramp. This arbitrary waveform generator can generate signals from -6 V to +6 V and uses direct digital synthesis (DDS) to precisely generate waveforms.
-
Product
RTSI Bus Cables for 2 PCI or AT/ISA Devices
776249-02
-
34-Pin Female RTSI to 34-Pin Female RTSI Ribbon Cable - The RTSI Cable, sometimes referred to as RTSI, connects RTSI bus connectors on adjacent NI plug-in boards. The RTSI Cable is offered with different numbers of ribbon connections and in different lengths.
-
Product
Switch Device for PCI Express
-
The Switch Device for PCI Express provides two PCI Express upstream ports and eight downstream ports. You can connect the downstream ports to external devices, such as a Software Defined Radio Reconfigurable Device, to create large multichannel, multiple input, multiple output (MIMO) systems. You can also connect multiple Switch Devices for PCIe to a single PXI Express chassis to create large MIMO systems with a Software Defined Radio Reconfigurable Device.
-
Product
IEC60558 Insulation Material Layer Abrasion Resistant Test Device
CX-J16
-
Shenzhen Chuangxin Instruments Co., Ltd.
This test is conforms to IEC60558-1 Fig6 and IEC60065 Fig14--16.The test shall be performed by fixing the specimens of thin sheets on a mandrel made of nickel plated steel or brass with smooth surface finish.
-
Product
Electronic Stethoscopes
-
Electronic Stethoscope Standard Headphones are designed to help locate the source of excess bearing and machine noise easily at low cost, it is an ideal easy to use listening device for mechanically generated noise in all types of applications, the 3.5mm jack socket tape output can also be fed into an audio tape recorder to store the data for either further analysis or as a reference for future comparison.
-
Product
Optical Mixed Signal Devices
-
Analog Devices optical mixed signal devices comprise a portfolio of highly integrated analog front ends and integrated optical modules. The discrete analog front ends offer flexibility in optimizing a given solution. The integrated optical modules are highly optimized for applications such as vital signs monitoring in smart watches and other wearables and offer very small form factors and reduce the required systems engineering to get to market.
-
Product
PCI-6521, 16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs (150 V), Isolated Digital I/O Device
779312-01
Digital I/O
The PCI-6521 is an industrial digital I/O module with high channel isolation and industry-standard 24 V logic levels. If a computer or application fault occurs, the PCI-6521 can use … digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. It also features programmable power-up states, digital filtering, and change detection for optimal control over your application.
-
Product
High Current Electronic Load (600W-1200W)
ELCH600 & ELCH1200
-
- Low lead resistance <5m Ohm for Fuel-cell- Battery Testing- VFD display- High resolution 0.1mA/1mV- Voltage range 0V to 500V- Working mode CV/CC/CW/CR- OV/OC/OP/OT protection- Communication: USB/RS232/GPIB
-
Product
Machine Vibration Monitoring Devices & Systems
Spider-80x
-
*Route Based Vibration Data Collection*Remote Condition Monitoring Software*Vibration Diagnostics System
-
Product
PCI-5152, 300 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device
779945-02
Oscilloscope
300 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device—The PCI‑5152 high-speed oscilloscope device has two channels that sample up to 2 GS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 300 MHz of analog bandwidth and flexible measurement configurations.
-
Product
Ettus USRP X410, 1 MHz to 7.2 GHz, 400 MHz Bandwidth, GPS-Disciplined OCXO, USRP Software Defined Radio Device
787272-01
-
The Ettus USRP X410 integrates hardware and software to help you prototype high-performance wireless systems and perform over-the-air signal generation and analysis. Additionally, the Ettus USRP X410 features a two-stage superheterodyne architecture with four independent transmitter and receiver channels. It also features a Xilinx Zynq Ultrascale+ RFSoC with programmable FPGA supporting the Open Source UHD tool flow as well as LabVIEW FPGA. With these features, the Ettus USRP X410 has the RF and processing performance for applications such as wireless communications prototyping, spectrum monitoring, and signals intelligence. The Ettus USRP X410 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) Reference Clock, which improves frequency accuracy and synchronization.
-
Product
Electronic Fuel Quantity Indicator
-
Proportional to the amount of fuel in the tank, thereby visibly indicating remaining fuel quantity to the pilot.
-
Product
High-Voltage Test Device
PGK 110 HB
-
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing of medium- and high-voltage cables* DC voltage testing of up to 110 kV output voltage with positive or negative polarity* AC voltage testing - up to 80 kV for switchgear, busbars and insulating elements* Easy-to-maintain 2-piece design
-
Product
SpaceWire EGSE & Device Simulator
312
-
The SpaceWire EGSE & Device Simulator is a programmable hardware unit designed specifically for generating sophisticated test schedules involving precision timing and creating accurate real-time simulations for SpaceWire enabled instruments.
-
Product
Electronic Inspection Systems
-
Intego's knowhow even makes it possible to identify challenging defects that may be located under the surface. One system is the inspection of chips by means of lock-in thermography, which visually represents the IR radiation intensity signal of electronics. Special lasers and flash lamps generate a very short heat impulse (10 ms) on the chip, which generates a measurable heat flow. In most cases, a resolution of < 1 μm can be achieved.
-
Product
General Data Acquisition Device With Strain Gage Measurement
Spider-80SG
-
The Spider-80SG is a high precision, general purpose data acquisition device featuring strain gage measurement. This device can be used in a variety of physical and measurement tests. The Spider-80SG can acquire data from a strain gage or a wide range of measurement quantities. A variety of general purpose and strain gage based sensors are supported.
-
Product
USB Device Server
DS-700
-
The Silex DS-700 is designed to easily connect and share USB devices over a network. Printers, scanners, disk drives, card readers, or virtually any other USB device can be now be enabled with network capability. It allows flexibility to place the USB device anywhere on the network instead of needing to be attached directly to the computer, and multiple users can access the USB device.
-
Product
USB-6356, 8 AI (16-Bit, 1.25 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
782261-01
Multifunction I/O
8 AI (16-Bit, 1.25 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6356 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6356 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCI-6503, 24-Channel, 5 V, TTL/CMOS, 2.4 mA Digital I/O Device
777690-01
Digital I/O
24-Channel, 5 V, TTL/CMOS, 2.4 mA Digital I/O Device - The PCI-6503 uses a 24-bit programmable peripheral interface (PPI). Each interface is Plug and Play compatible and does not require a separate card manager for configuration. The PCI-6503 can interface to peripherals or other computers, and it can operate in either a unidirectional or bidirectional mode and handshake with peripheral equipment.
-
Product
Intelligent Liquid Level Transmitter
HR8000/K/RK
-
HighReach Measuring & Controlling System Co.,Ltd
HR8000 intelligent liquid level transmitter is an input type liquid level measuring instrument, which realizes full-scale digital linear correction, digital temperature error compensation in full temperature zone, and stores compensation parameters in non-volatile memory, adopting multiple security protection mechanisms. Of the product being unusable due to the loss of the calibration parameters is avoided; the circuit module has the power supply monitoring, the watchdog monitoring function, and the input structure is all stainless steel sealed, which greatly improves the reliability of the product.
-
Product
Electronic Pressure Comparator
-
Huaxin Instrument (Beijing) Co., Ltd
When it comes to simultaneous pressure calibration for several pressure measuring instruments, electronic pressure comparator is always a great choice for most of people. The comparison calibrator features 5 pressure ports which allow simultaneous connection of 4 pressure gauges under test, making calibration more efficient and time saving. It also comes with an external air source for easy and precise pressure generation and servo valve for stable pressure control.
-
Product
IEC60884-1 Low Temperature Thermal Shock Test Device
CX-DWC
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884-1 Uses: It is used to evaluate the impact resistance of electrical accessories under low temperature conditions, and also to evaluate the low temperature impact resistance of wire and cable.
-
Product
Air Quality Sensing Device
Air quality 4 click
-
Air quality 4 click is an advanced air quality sensing device that combines multiple metal-oxide sensing elements on a chip to provide detailed information of the air quality parameters. This click can output a TVOC value readings as well as the CO2 equivalent concentration readings in an indoor environment.
