-
Product
Wear Testing Machine
M-2000
-
Jinan Testing Equipment IE Corporation
Model M-2000 Wear Testing Machine is to be used test the anti-wear performance for metal and non-metal specimen under the sliding, rolling, and sliding-rolling condition. The Wear Testing Machine can also test various materials under dry-friction and wet-friction. The wear testing system can calculate friction work & friction coefficient by the data acquired. The Wear Testing Machine is widely used in universities, research & scientific institutes.
-
Product
Universal Wear Tester
TF213
-
TESTEX Testing Equipment Systems Ltd.
Universal Wear Tester, to determine the wear and abrasion resistance of fabric used in clothing, footwear and industrials. Universal wear tester Supplies with surface abrasion head (inflated diaphragm method) and Flex abrasion head as well as necessary weights and initial supply of abrasives. Accessories are available for conducting frosting, pilling and edge abrasion tests.
-
Product
Conventional friction and wear tester
EFM-III
-
The measurement unit of A&D's conventional friction and wear tester has been adjusted to enable the measurement of friction characteristics with higher precision.
-
Product
High-pressure environmental friction and wear tester
-
This testing machine is used to evaluate the frictional characteristics in a pressure container. It can evaluate the frictional characteristics of refrigerants, oil, friction materials, etc. for compressors and so on. It has a load cell inside the pressure container to enable frictional-force measurement with high accuracy.
-
Product
Abrasion/Wear
-
Our Capabilities*Taber Abrasion*RCA Wear Tester*Resistance to Crocking*Washability*Pencil Hardness*Finish Adhesion
-
Product
Friction and Wear Tester
EFM-III Series
-
The EFM-III series is a friction and wear tester for tribology evaluation in conformity with JIS K 7218. This tester is designed for scientific elucidation and technical evaluation of the characteristics relating to sliding friction, wear and lubrication, that are surface behaviors of relative properties of two interacting material surfaces (relative properties of solid materials in relative motion).
-
Product
Uniform Wear Tester
DRK546A
-
Shandong Drick Instruments Co., Ltd.
Instrument purpose: It is used to evaluate the abrasion resistance of stretchy knitwear.
-
Product
Power Circulation Type Tire Wear Tester
-
This test machine is a tire wear test device that employs an electric servomotor power circulation system.
-
Product
Ferrous Wear Metal Measurement In Lubricants
FerroCheck 2000 Series
-
The FerroCheck 2000 Series of portable ferrous analyzers offer accuracy and convenience for total ferrous measurement of in-service lubricating oil and grease. Fast and easy to use samples are analyzed in less than 30 seconds. Small sample volumes of just 1.5 ml of oil or 0.75 ml of grease are needed to measure ferrous content in part per million (ppm) by weight. The FerroCheck measures the total ferrous content of both small particles from normal machine wear and large abnormal wear particles.
-
Product
Universal Wear Tester
TF213
-
TESTEX Testing Equipment Systems Ltd.
Universal Wear Tester, to determine the wear and abrasion resistance of fabric used in clothing, footwear and industrials. This Wear Testing Machine complies with ASTM D3514/D3885/D3886, AATCC 119/120, FTMS 191/5300/5302, etc.
-
Product
Test Contactor
RF Scrub
-
RF Scrub™ Test Contactor’s innovative design combines an extremely short signal path (0.90mm test height) with high wear resistance pins that can operate in a wide temperature range.The RF Scrub Test Contactor’s long-life, elastomer free design and easy field maintainability makes it an optimal solution for testing of high-performance devices.The RF Scrub design minimizes load board wear and with the unique pin base material and plating, the cleaning intervals can last up to 100,000 cycles.
-
Product
Class 1 Integrating Sound Level Meter System
NK021
-
This NK021 system includes a class 1 integrating sound level meter, class 1 acoustic calibrator, protective microphone windshield and is supplied in a hard wearing kit case.
-
Product
ICI Mace Snag Tester
-
TESTEX Testing Equipment Systems Ltd.
ICI Mace Snag Tester, to determine the tendency of fabrics to snag (pull yarn loops from fabric) in normal wear (mace snag). ICI Mace Snag Tester complies with ASTM D3939, etc. Please contact us for more information about snagging test.
-
Product
PFR96
2WE06
-
The digital controller PFR96 can manage up to 12 independent batteries, a communications port, and two current inputs in size from 96×96 framework. Particularly easy to program thanks to a basic configuration with two parameters and advanced that allows the advanced user the most complete of the power factor correction control.The onboard logic allows corregegre setup via an erroneous wiring of the picture as to or stage of TA.10ms sampling of the voltage allows the calculation of the RMS voltage continuously, identifying network holes and temporary interruptions and detach the active steps immediately to the protection of the contactors and benches.The PFR96 can handle numerous alarms associated to available relays.The means of intervention in the PFR96 adjustment are all customizable for a better quality of the intervention as well as the use of different banks can be equalized for less wear of the contactors.Sampling at variable frequency and RS485 communication for remote control (PFR96 Plus) complete a range of services offering maximum control and quality of the measurement
-
Product
Laboratory Ferrography
T2FM 500
-
The SpectroT2FM 500 Analytical Ferrography Laboratory is a complete analytical system for the separation and interpretation of wear and contaminant particles in used lubricant oils, hydraulic fluids, coolants and fuels. It consists of the T2FM Ferrogram maker, a bichromatic microscope, video camera and image capture software.
-
Product
Meter Test Bench
-
Meter Test Banch is available with high-technology to ensure high testing accuracy as well as maximum functionality. It is designed to provide precise results in any simple to complex testing. It comes with modern systems to ensure to provide artificial load that cannot be changed in the power supply. It is provided with high durability and efficacy to ensure long lasting life with no maintenance. In addition to this, it ensures high accuracy in testing without any wear.
-
Product
Lube Oil Analysis Options
-
Maintenance Reliability Group, LLC
MRG’s experts have been performing in-depth oil analysis for over 25 years. Our Lube Oil Analysis monitors the health of oil-lubricated equipment with a comprehensive testing slate. Oils are assessed in three categories: Wear, Oxidation and Physical Properties.
-
Product
Turbine Flow Meters
-
Axial turbine flow meters are designed with wear resistant internal components to provide trouble-free operation and a long service life. Fluid entering the flow meter is first conditioned by the inlet flow straightener which reduces turbulence in the fluid. The moving fluid causes the rotor to spin at a speed that is proportional to its flow rate. As the turbine blades on the rotor pass through the magnetic field of the pickup, an electronic pulse is generated.
-
Product
13 GHz, 4 Channel Programmable Attentuator
QPA13
-
This device has low impedance mismatch, high bandwidth, wide dynamic range and is capable of rapid state change. The QPA13 can be an attractive alternative to either the manually operated microwave attenuator switches, which are expensive and are switched very slowly, or the relay attenuators which are expensive and wear out quickly.
-
Product
Resistivity Meters
-
Periodic compliance checks of ESD work surfaces are super important. Monitors only verify the ground plane, or path to ground. The surface itself can wear down, become dirty, or if you use low quality mat—just not hold up. A handheld Surface Meter is great for running monthly, or prescriptive compliance verification of your ESD surfaces.
-
Product
Charge Plate Monitor
-
The electrostatic resistance of electronic devices is declining, and the number of ionizers installed is increasing. Ionizers cause deterioration of static elimination performance and imbalance of ions due to dirt and wear of the discharge electrode needle. Charging of electronic devices is also caused by ion blow. of an ionizer that is out of balance due to dirt and wear, and reaches a level that destroys advanced electronic devices.The atmospheric ion monitor measures the potential of the charging plate (detector), which has almost the same capacitance as the device's ground capacitance , with high accuracy, and is the most suitable measuring instrument for checking the effect when installing the ionizer and for daily management.
-
Product
ADI Test Fixture
TA-6500
-
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) type connector to minimize contact wear. The expanded localizer and nav input pins J2-34/35 are exposed on the panel to facilitate the insertion of a 200 ohm shunt when required. The fixtures rear panel has connectors for the required dual API/Synchro transmitter interface while the panel switches provide the correct routing of each.
-
Product
High Speed Test Bench
AT444
Test Platform
AC motor with mechanical multiplying gearbox test benches allow precise programming of all drive parameters required for accurate rotating devices test.The use of special high-speed bearings, mechanical components and parts wear resistant leads to a large life. The supply includes the electronic drive and control as well as the entire oil cooling unit.
-
Product
Standard Digital Multimeter - Auto Ranging
MM39
-
The MM39 is an auto-ranging multimeter with a large rotary switch for easy selection of the required test, even when wearing gloves. There are two test buttons, one to lock the range and the other to hold the results which are displayed on a 3½ digit LCD screen.
The main test functions are AC voltage and DC voltage and current and resistance. The MM39 measures both AC and DC voltage between 0.1mV to 600V and AC and DC current between 10mA to 10A. There is a diode test and an audible continuity test which sounds at less than 25Ω.
-
Product
Tire Durometer
Model 2100
-
Tire hardness can be a critical factor in setting up a race car. A tire that's too hard may sacrifice traction, while a tire that's too soft may give great traction but wear too quickly, and an unmatched set of tires may result in an ill handling car. To properly set up a car, a measure of tire hardness is necessary, and the easiest and most cost-effective way to obtain such a measure is to use a durometer.
-
-
Product
Blast Nozzle Gauge
103
-
The Elcometer 103 Blast Nozzle Gauge measures the orifice size of an abrasive blasting nozzle. This gauge is used to determine the nozzle orifice wear which leads to low nozzle pressure and decreased efficiency in its performance. Nozzle orifice wear results in decreased productivity and increased abrasive media consumption.
-
Product
Hardness & Scratch Resistance
-
Hardness can be defined as a material’s resistance to permanent deformation. In the coatings industry, hardness measurement can be used to determine the resistance of the coating to scratching from general wear and tear and also if a coating is fully cured.
-
Product
Affordable ICP-OES Spectrometer
Ultima Expert LT
-
HORIBA Scientific develops and manufactures high performance ICP-OES spectrometers for more than 35 years.• The new Ultima Expert LT provides high performance at affordable price for laboratories with challenging samples.• Ultima Expert LT integrates high efficiency Jobin Yvon optical design capable to achieve optimal performance for a large variety of sample types and matrices.• Ultima Expert LT is driven by the powerful Analyst software featuring a large variety of analytical functionalities for tailored control and analysis.• The robustness of the Ultima Expert LT makes it ideal for applications common to mining, chemicals manufacture, salt production, wear metals in oil analysis, petrochemical and metallurgical production• Gain in performance with the Ultima Expert LT for your most challenging applications!
-
Product
High Resolution Encoders
HR-E
-
The High Resolution 8-dial Encoder (HR-E) from Badger Meter uses a non-contact field-proven light emitting diode technology to provide a high resolution 8-digit reading while at the same time eliminating friction and wear of traditional mechanical encoders. The HR-E communicates using the industry standard ASCII communication protocol to provide high resolution encoded output.
